Multiresidue determination of pesticides in soil by gas chromatography-mass spectrometry detection

An analytical multiresidue method for the simultaneous determination of various classes of pesticides in soil was developed. Pesticides were extracted from soil with ethyl acetate. Soil samples were placed in small columns, and the extraction was carried out assisted by sonication. Pesticides were determined by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode. Spiked blank samples were used as standards to counteract the matrix effect observed in the chromatographic determination. Pesticides were confirmed by their retention times, their qualifier and target ions, and their qualifier/target abundance ratios. Recovery studies were performed at 0.2, 0.1, and 0.05 microg/g fortification levels of each pesticide, and the recoveries obtained ranged from 87.0 to 106.2% with a relative standard deviation between 2.4 and 10.6%. Good resolution of the pesticide mixture was achieved in approximately 41 min. The detection limits of the method ranged from 0.02 to 1.6 microg/kg for the different pesticides studied. The developed method is linear over the range assayed, 25-1000 microg/L, with determination coefficients >0.999. The proposed method was used to determine pesticide levels in real soil samples, taken from different agricultural areas of Spain, where several herbicides and insecticides were found.     

Comparison of strategies for extraction of high molecular weight polycyclic aromatic hydrocarbons from drinking waters

Simple, rapid, and inexpensive methods have been developed for the determination of polycyclic aromatic hydrocarbons (PAHs) in drinking waters without interferences from other chemical contaminants by use of two different extraction techniques and analysis by an optimized reverse-phase (RP) high-performance liquid chromatography followed by fluorescence detection (HPLC-FLD) method. The feasibility of SPE (solid-phase extraction) and SPME (solid-phase microextraction) for the determination of PAH in drinking water samples has been evaluated. Several parameters have been studied and optimized for both extraction procedures. The relationship between the nature of the fibers and the quantity of extracted compounds and the effects of organic solvent, salt addition, sampling temperature, and sampling time was studied for SPME. Acetonitrile percentage added to the sample, sample storage conditions (temperature and time), and type of organic elution solvent and elution volume were evaluated for SPE. The results show that both extraction procedures can be used to determine PAHs in drinking waters, but SPE gives better performance (recovery, precision, and quantification limits) for the determination of PAHs in drinking water at the levels established by the legislation.     

Solid phase extraction gas chromatography/electron capture detector method for the determination of organochlorine pesticides in wildlife whole blood.

A gas chromatographic method for the analysis of 10 organochlorine pesticides in 0.5 mL of whole blood is described. Sample preparation involved an ethyl ether and hexane extraction, followed by a silica solid phase extraction cleanup. The pesticides are quantified by gas chromatography/electron capture detection. Method limits of detection ranged from 1.1 to 5.2 microg/L. The mean and standard deviation for the recovery of 10 pesticides was 97.9 +/- 5.5%. Recoveries from whole blood were comparable to recoveries from plasma. This indicates that the preparation of plasma is unnecessary for the quantification of organochlorine pesticides in blood. This approach is particularly useful as a nonlethal approach for monitoring pesticide contamination in small animals for which the volume of blood is limiting.     

Ethanol-modified subcritical water extraction combined with solid-phase microextraction for determining atrazine in beef kidney

The determination of the levels of pesticides in food products has prompted the development of sensitive and rapid methods of analysis that are solvent-free or utilize solvents that are benign to the environment and laboratory worker. In this study we have developed a novel extraction method that utilizes ethanol-modified subcritical water in combination with solid-phase microextraction (SPME) for the removal of atrazine from beef kidney. In situ sample cleanup was achieved using the technique of matrix solid-phase dispersion. A cross-linked polymer, XAD-7 HP, was utilized as a dispersing material for kidney samples. Subcritical water extractions were performed with a pressurized solvent extraction unit at 100 degrees C and 50 atm. Experimental parameters investigated were the volume of solvent and amount of modifier required for the complete extraction of atrazine and optimization of the extraction time. It was determined that 30% ethanol in water (v/v) is adequate for the complete extraction of atrazine. A Carbowax-divinylbenzene SPME fiber was used to sample the aqueous extracts. Analysis of the fiber contents was by ion-trap GC/MS utilizing the single ion mode. The total time of analysis for a single kidney sample is 90 min. The average percent recoveries from samples spiked to the concentrations of 2 and 0.2 microg/g were 104 and 111, respectively. The average relative standard deviations were 10 and 9, respectively. The method limit of detection for beef kidney spiked with atrazine was found to be 20 ng/g of sample.     

Multi-residue analysis of PAH, PCB, and OCP optimized for organic matter of forest soil

Purpose

Analyzing organic pollutants in forest soil is challenging because they are strongly physical and chemical bound to soil organic matter (SOM). Within the framework of a forest soil inventory, an analytical protocol for the determination of polycyclic aromatic hydrocarbons (PAH), polychlorinated biphenyls (PCB), and organochlorine pesticides (OCP) should be established and validated using one and the same extraction and cleanup procedure. The protocol should be applicable for reliable analysis of a high number of samples in a short timeframe.

Materials and methods

Two different soil samples representative for the humic layer from a typical mixed and coniferous forest soil had been used for the analysis. Three solvents of different polarity, namely cyclohexane (CH), ethylacetate (EA)/CH (1/1, v/v), and acetone (AC)/CH (2/1, v/v), and the six standard extraction techniques (pressurized liquid extraction (PLE), soxhlet extraction, fluidized bed extraction, sonication, shaking, and one-step extraction recommended for analyzing agricultural soil in Germany (VDLUFA 2008)) were compared concerning their extraction efficiency. For additional matrix separation, two different cleanup procedures (gel permeation chromatography (GPC) and solid-phase extraction (SPE) with different sorbents) were tested. Quantification was carried out using gas chromatography combined with mass spectrometry (GC–MS) and two different injection systems (split/splitless injection and programmable temperature vaporizer (PTV) injection). Labeled internal standards, added prior to extraction, were used for method evaluation.

Results and discussion

For the simultaneous extraction of PAH, PCB, and OCP from organic forest soil PLE with acetone/cyclohexane (2/1, v/v) provided the highest extraction efficiency. A two-step cleanup procedure consisting of GPC followed by SPE with silica gel was entirely sufficient for the separation of humic substances without discrimination of analytes. Recovery rates for the different extraction and cleanup steps ranged between 89% and 106%. For quantification, a GC–MS method was developed using two different injection systems and two capillary columns of different selectivity.

Conclusions

By comparing six standard extraction techniques for PAH, PCB, and OCP from forest soil, we obtained the highest extraction efficiency when using PLE with AC/CH (2/1). For sample injection, we achieved best results using an optimized PTV injection system as it highly reduced the breakdown of thermolabile pesticides. Using this combination of technical equipment, it is possible to determine a concentration of the analytes in the trace level range of 1–2 μg kg^?1 in humic soil.     

Sulfuric acid cleanup and KOH-ethanol treatment for confirmation of organochlorine pesticides and polychlorinated biphenyls: application to wastewater samples

The efficacy of sulfuric acid cleanup and KOH-ethanol hydrolysis confirmation was studied for 22 organochlorine pesticides and 2 polychlorinated biphenyls (PCBs). Mean recoveries for different treatment times are given. The method was applied to analysis of several wastewater samples by gas chromatography with electron capture detection. Organochlorine compounds were extracted by using separatory funnels and 15% diethyl ether in hexane as extractant. All the compounds studied could be analyzed except trifluralin, dichloran, dieldrin, and endrin, which were destroyed after treatment with concentrated H2SO4. The pesticides found most commonly in the samples analyzed were fenson, tetradifon, lindane, methoxychlor, and dicofol.     

Focused microwave assistance for extracting some pesticide residues from strawberries into water before their determination by SPME/HPLC/DAD.

A novel and simple method for the determination of some pesticide residues in strawberries using both focused microwave-assisted extraction (FMAE) and solid-phase micro extraction (SPME), coupled with high-performance liquid chromatography (HPLC), has been developed. The pesticides were first extracted from strawberries with water and the assistance of focused microwaves at 30 W for 7 min. Then, an aliquot of the resulting aqueous extract was subjected to SPME with a 60-microm thick poly(dimethylsiloxane)/divinylbenzene (PDMS/DVB) fiber for 45 min at room temperature, with the solution being stirred at 1000 rpm. The extracted pesticides on the SPME fiber were desorbed into the SPME/HPLC interface for quantitative analysis with a diode array detector (DAD). The whole sample pretreatment procedure before chromatographic analysis did not use any organic solvents or involve any blending or centrifugation steps. The five compounds (carbendazim, diethofencarb, azoxystrobine, napropamide, and bupirimate) were chosen because they cannot be analyzed easily by GC. The efficiency of this relatively fast procedure was comparable to that of previously reported methods, with detection limits at low microg/kg levels and linear responses in the range from 0.05 to 1 mg/kg of pesticide in strawberries, with RSDs between 3 and 7.3%, depending on the analyte. In all but one case results obtained by this method for field-incurred samples were comparable to those obtained with traditional methods.     

Gas chromatographic determination of electron capture sensitive volatile industrial chemical residues in foods, using AOAC pesticide multiresidue extraction and cleanup procedures

Electron capture (EC) gas chromatographic (GC) parameters have been developed for determining some of the more volatile industrial chemicals that can be determined by the AOAC multiresidue method for organochlorine and organophosphorus pesticides with modified GC operating conditions. Retention times relative to pentachlorobenzene are reported for 143 industrial chemicals, pesticides, and related compounds on OV-101 GC columns at 130 degrees C. Also reported for most of the compounds are recoveries from fortified samples carried through the AOAC extraction and cleanup procedures for fatty and/or nonfatty foods, Florisil elution characteristics, and GC relative retention times on mixed OV-101 + OV-210 columns at 130 degrees C. Our laboratory has used the modified EC/GC parameters with the AOAC multiresidue extraction/cleanup procedures to determine many volatile halogenated industrial chemical contaminants in foods, chiefly in samples of fresh-water fish. Other modifications of the AOAC method are described to improve the tentative identification and quantitative measurement of these volatile residues.     

A headspace solid-phase microextraction method for the determination of some secondary compounds of Brazilian sugar cane spirits by gas chromatography

A headspace solid-phase microextraction (SPME) method was developed for the determination of secondary compounds from Brazilian sugar cane spirits, or cacha?a, by GC-FID. An SPME holder with an 85 microm polyacrylate coating was utilized. The novel method is compared with an optimized method: liquid-liquid extraction (LLE). Both methods showed good linearity, but the repeatability for analyses done with the SPME technique (%RSD = 1.8-3.9) was better than for those done with LLE (%RSD = 10.3-11.7). The concentrations of the analytes obtained in the analysis of 12 cacha?a samples with the SPME technique were higher than those obtained with LLE. In the SPME method the extraction wastes are smaller. Cacha?a samples were qualitatively analyzed for GC-MS.     

有机溶剂对有机氯农药污染场地土壤淋洗修复效用研究

Problems associated with organochlorine pesticide (OCP)-contaminated sites in China have received wide attention. To solve such problems, innovative ex-situ methods of site remediation are urgently needed. We investigated the feasibility of the extraction method with different organic solvents, ethanol, 1-propanol, and three fractions of petroleum ether, using a soil collected from Wujiang (WJ), China, a region with long-term contamination of dichlorodiphenyltrichloroethanes (DDTs). We evaluated different influential factors, including organic solvent concentration, washing time, mixing speed, solution-to-soil ratio, and washing temperature, on the removal of DDTs from the WJ soil. A set of relatively better parameters were selected for extraction with 100 mL L 1 petroleum ether (60-90℃): washing time of 180 min, mixing speed of 100 r min 1 , solution-to-soil ratio of 10:1, and washing temperature of 50℃. These selected parameters were also applied on three other seriously OCP-polluted soils. Results demonstrated their broad-spectrum effectiveness and excellent OCP extraction performance on the contaminated soils with different characteristics.     

Evaluation of a modified QuEChERS extraction of multiple classes of pesticides from a rice paddy soil by LC-APCI-MS/MS

A new method for the determination of clomazone, fipronil, tebuconazole, propiconazole, and azoxystrobin in samples of rice paddy soil is presented. The extraction of the pesticides from soil samples was performed by using a modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) method. Some extraction conditions such as salt addition, sample acidification, use of buffer, and cleanup step were evaluated. The optimized method dealt with a single extraction of the compounds under study with acidified acetonitrile, followed by the addition of MgSO(4) and NaCl prior to the final determination by liquid chromatography-atmospheric chemical pressure ionization-tandem mass spectrometry. Validation studies were carried out in soil samples. Recoveries of the spiked samples ranged between 70.3 and 120% with relative standard deviation lower than 18.2%. The limits of quantification were between 10 and 50 μg kg(-1). The method was applied to the analysis of real samples of soils where rice is cultivated.     

Determination of organochlorine and organophosphorus pesticide residues in eggs using a solid phase extraction cleanup

A multiresidue solid phase extraction (SPE) method for the isolation and subsequent gas chromatographic determination of nonpolar organochlorine and polar organophosphorus pesticide residues in eggs is described. The method uses an acetonitrile extraction followed by an SPE cleanup using graphitized carbon black and aminopropyl SPE columns. Organophosphorus pesticides are determined by gas chromatography with flame photometric detection. After further cleanup of the extract using Florisil SPE columns, organochlorine pesticides are determined by gas chromatography with electron capture detection. Studies were performed using eggs containing both fortified and incurred pesticide residues. The average recoveries were 86-108% for 8 fortified organochlorine pesticide residues and 61-149% for 28 fortified organophosphorus pesticide residues.     

Determination of pesticides and PCBs in virgin olive oil by multicolumn solid-phase extraction cleanup followed by GC-NPD/ECD and confirmation by ion-trap GC-MS

A multicolumn solid-phase extraction cleanup for the determination of organophosphorus (OP) and organochlorine (OC) pesticides plus PCB congeners in virgin olive oil is presented. The method involves dissolution of the olive oil in hexane, followed by a cleanup system using a diatomaceous earth column (Extrelut-QE) with reversed (C(18)) and normal (alumina) phase SPE columns. Determination of OPs was by GC-NPD, while the OCs and PCBs were analyzed using GC-ECD. Recovery assays for OPs varied from 81.7% to 105.3%, for OCs ranged between 74.3% and 99.4%, while for PCBs were from 60.1% to 119.2%. Quantitation limits ranged from 10 to 25 microg/kg olive oil for OPs, and from 1 to 6 microg/kg olive oil for OCs and PCBs. In the case of positive samples, the confirmation of pesticide identity was performed by ion-trap GC-MS/MS. The applicability of the method was assayed with 19 virgin olive oil samples collected from different olive mills of Aragón (Spain). Only one OP pesticide (acephate) was detected in one sample at a concentration of 10 microg/kg. Organochlorine pesticides were found in 5-47% of samples at very low levels ranging from 1.5 to 5.2 microg/kg. PCBs were found in 20-90% of samples, showing concentrations between 2.3 and 17.3 microg/kg.     

Levels of organochlorine pesticides in soils and rye plant tissues in a field study

The organochlorine pesticides are lipophilic and persistent and tend to accumulate in soils and growing plants. The contamination of growing plants occurs by adhesion of volatile substances from the air to the plant surface and by the migration of contaminants through xylem in inner ascendant transport. Persistent organochlorine pesticides (HCB, alpha,gamma-HCH, pp'DDE, op'DDT, pp'DDT) levels were determined in soils and rye plants. The aims of the study were the monitoring of organochlorine pesticide concentrations and the comparison of these levels among soil, rye straw, and rye grains. Fifty soil samples and 50 rye plant (50 straw and 50 grains) samples were taken. The GLC-ECD chromatographic results indicated the following contamination levels distributed among soil, straw, and grains: HCB (0.7-1.2-0.7 microg.kg(-1)), alpha-HCH (0.6-3.4-1.2 microg.kg(-1)), gamma-HCH (1.8-27.3-4.4 microg.kg(-1)), Sigma-HCH (2.5-30.7-5.6 microg.kg(-1)), pp'DDE (1.0-7.8-5.5 microg.kg(-1)), op'DDT (16.1-20.4-17.0 microg.kg(-1)), pp'DDT (38.0-41.7-49.6 microg.kg(-1)), and Sigma-DDT (54.2-63.2-72.1 microg.kg(-1)). The study verified the presence of organochlorine pesticides in the Mexican agricultural environment and their migration from soil to the growing rye plants. However, DDT has been banned since 1999 for sanitary reasons, and Lindane is applied only in some cases as a seed dresser. The determined organochlorine pesticide levels in rye plants are low, at residual levels that are below Codex Alimentarius Commission maximum residue limits.     

Determination of organophosphorus pesticides in fruit juices by matrix solid-phase dispersion and gas chromatography

A rapid multiresidue method was developed for the determination of nine organophosphorus pesticides in fruit juices. The analytical procedure is based on the matrix solid-phase dispersion (MSPD) of juice samples on Florisil in small glass columns and subsequent extraction with ethyl acetate assisted by sonication. Residue levels were determined by gas chromatography with nitrogen-phosphorus detection. Spiked blank samples were used as standards to counteract the matrix effect observed in the chromatographic determination. The NPD response for all pesticides was linear in the concentration range studied with determination coefficients >0.999. Average recoveries obtained for all of the pesticides in the different juices and fortification levels were >70% with relative standard deviations of <11%. The detection limits ranged from 0.1 to 0.6 microg/kg. The identity of the pesticides was confirmed by gas chromatography with mass spectrometric detection using selected ion monitoring. The proposed MSPD method was applied to determine pesticide residue levels in fruit juices sold in Spanish supermarkets. At least one pesticide was found in most of the samples, although the levels detected were very low, far from the maximum residue levels established for raw fruit.     

Analysis of pesticides in honey by solid-phase extraction and gas chromatography-mass spectrometry

An analytical method for the simultaneous determination of 51 pesticides in commercial honeys was developed. Honey (10 g) was dissolved in water/methanol (70:30; 10 mL) and transferred to a C(18) column (1 g) preconditioned with acetonitrile and water. Pesticides were subsequently eluted with a hexane/ethyl acetate mixture (50:50) and determined by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC-MS-SIM). Spiked blank samples were used as standards to counteract the matrix effect observed in the chromatographic determination. Pesticides were confirmed by their retention times, their qualifier and target ions, and their qualifier/target abundance ratios. Recovery studies were performed at 0.1, 0.05, and 0.025 microg/g fortification levels for each pesticide, and the recoveries obtained were >86% with relative standard deviations of <10%. Good resolution of the pesticide mixture was achieved in approximately 41 min. The detection limits of the method ranged from 0.1 to 6.1 microg/kg for the different pesticides studied. The developed method is linear over the range assayed, 25-200 microg/L, with determination coefficients of >0.996. The proposed method was applied to the analysis of pesticides in honey samples, and low levels of a few pesticides (dichlofluanid, ethalfluralin, and triallate) were detected in some samples.     

Multiresidue analysis of pesticides in soil by gas chromatography with nitrogen-phosphorus detection and gas chromatography mass spectrometry

A rapid multiresidue method for the simultaneous determination of 25 fungicides and insecticides in soil was developed. Soil samples are extracted by sonication with a water-acetonitrile mixture, and the pesticides are partitioned into dichloromethane. Final determination was made by gas chromatography (GC) with nitrogen-phosphorus detection (NPD). Confirmation analysis of pesticides was carried out by GC-MS in the selected ion monitoring (SIM) mode. The identification of compounds was based on retention time and on comparison of the primary and secondary ions. The average recovery by the GC-NPD method obtained for these compounds varied from 68.5% to 112.1% with a relative standard deviation between 1.8% and 6.2%. The GC-NPD method presents good linearity over the range assayed 50-2000 microg/L, and the detection limit for the pesticides studied varied from 0.1 to 10.4 microg/kg. The proposed method was used to determine pesticide levels in soil samples from experimental greenhouse pepper cultivation.     

Multiresidue screening of pesticides in fruits using an automatic solid-phase extraction system

About 20 pesticides were determined in lyophilized fruits using a semiautomatic multiresidue method, based on solid-phase extraction (SPE) with a silica column. The lyophilization of the sample, besides the SPE procedure selected, provided clean extracts despite the complexity of the matrixes studied. In addition, the lyophilization process allows sample preservation for at least three months without changes in the concentrations of the pesticides. Determination and quantitation of organochlorine and pyrethroid residues was carried out using a gas chromatograph equipped with an electron capture detector (GC-ECD), and a mass spectrometric detector (GC-MS) was used for confirmation purposes. Organochlorine pesticides provided average recoveries (spiked at three concentration levels in eight different fruits) near 93 +/- 4%, being lower (89 +/- 8%) for pyrethroids as a consequence of their higher degradation and interaction with the sample matrix. On the other hand, the detection limits achieved for all pesticides (0.5-8 ng per g of lyophilized fruit) allow their determination at the MRLs established by the European Union, with good precision ( approximately 5%). Finally, from the 100 different fruits screened, only 10 positive responses were obtained, which were further confirmed by GC-MS.     

Characterization of pyrazines in some Chinese liquors and their approximate concentrations

Pyrazines are very important impact aroma compounds in Chinese liquors. The identification of pyrazine derivatives was carried out by liquid-liquid extraction (LLE). The liquor sample was adjusted to the H(+) concentration of 1 N with 12 N HCl and then concentrated by rotatory evaporator under vacuum condition. The concentrated liquor was extracted by diethyl ether, and the residual aqueous phase was adjusted to pH 10. The basic compounds were detected and identified by gas chromatography (GC)-mass spectrometry (MS). A total of 27 pyrazines were identified in Chinese liquors, mainly alkyl- and acetylpyrazines. A method for determining pyrazines in Chinese liquors was developed. It involves extraction by headspace (HS) solid phase microextraction (SPME) and determination using GC-flame thermionic detector (FTD). The optimum method was that the sample alcohol concentration was diluted to 12% vol by freshly redistilled-deionized water, and the diluted samples were saturated with NaCl and equilibrated at 50 degrees C for 15 min and extracted for 30 min at the same temperature. The developed method enabled detection limits of <200 ng/L. Linearity (R(2) > 0.99) and recovery rate were satisfied in all cases. Pyrazines of 12 commercial typical Chinese liquors were quantified by HS-SPME followed by GC-FTD and had a wide range of concentration.     

Potential of a simple mechanical extraction system for the rapid extraction of pesticides from foodstuffs. Application to the determination of organochlorine pesticides in lettuce.

The efficiency of a simple mechanical extraction system as applied in veterinary drug analysis has been tested in the field of pesticide residue analysis. As a first application, the system was used for the extraction of organochlorine pesticides from vegetables. The convenience of this simple extraction system consists of performing mechanical extraction in disposable polyethylene-based extraction bags, reducing considerably manual operation and cross-contamination. For the tested compounds and matrix (lettuce), recoveries of the 10 organochlorine pesticides performed at two spiking levels (n = 4 each level and compound) ranging between 0.06 and 3.3 mg/kg were between 60 and 80%, with most standard deviations <5%. The extraction method appeared to be simple and fast with a great potential for the analysis of many pesticide-matrix combinations.