不同加载方式SIP墙体的抗剪性能

以3种不同的单向加载方式对以木质OSB覆面的SIP墙体进行侧向加载实验,对比分析3种加载方式下SIP墙体的破坏形式及这3种加载方式对墙体抗剪性能参数的影响,结果表明:3种加载方式得到的墙体的抗剪性能指标有所差异,其中,采用ISO22452加载协议,即对墙体施加持续增加载荷的加载方式所得到的极限承载力最大、极限位移和延性系数居中,分别为46.06 kN、71.83 mm、3.31;采用ASTM E72-05加载时极限承载力居中、极限位移及延性系数最大,分别为:40.66 kN、76.97 mm、4.07。采用ASTM E564-06加载,即对墙体施加阶段载荷并使阶段目标载荷持续作用一段时间的方式,所得到的极限承载力、极限位移及延性系数最小,分别为37.73 kN、54.92 mm、2.91;3种加载方式对墙体破坏形式的影响不大。     

节理岩体中连拱隧道施工对周边建筑物的影响

以重庆东水门大桥—千厮门大桥渝中区连接隧道为研究对象,基于UDEC软件建立离散元数值模拟分析模型,研究了城区连拱隧道施工引起的地表沉降,上部建筑物基础沉降及倾斜,新建隧道下方已有轨道六号线的变形、受力特征,并将监测数据与数值模拟进行对比分析。结果表明,连拱隧道左侧隧道上导坑施工引起的隧道拱顶沉降和基础沉降量最大,经计算上部建筑物基础最大沉降量为3.81 mm,最大倾斜量为0.02%,建筑物基础沉降量和倾斜在规范许可范围之内;隧道施工引起的地层损失使得轨道六号线左拱肩向上隆起,六号线弯矩分布规律和其变形形态基本一致,弯矩最大值位于左拱肩部位,最大值为238 kN·m;数值模拟计算结果与监测数据量值相当,变形趋势基本一致;采用UDEC软件可以准确地计算出隧道开挖过程中节理的存在对隧道周围建筑物变形的影响。     

夯土-水硬石灰与石英砂浆液-木锚杆锚固系统性能

运用室内物理模型试验和原位试验,对基于水硬石灰与石英砂浆液的木锚杆锚固系统在夯土介质中进行了拉拔测试与杆体-浆体界面应变监测,研究了该锚固系统的锚固性能与破坏模式、杆体-浆体界面剪应变分布与传递特征。试验结果表明,该锚固系统50 cm锚固长度可以提供30~45 kN(室内)与16.2~19 kN(现场)的极限锚固力;锚固系统具有较强的延性;在加载进程中杆体-浆体界面的应力分布与传递特征具有单峰值或双峰值分布、界面应力向锚固末端传递、压应力出现在锚固段中末端等特征,表现出复杂的受力特性。研究结果表明,该锚固系统在结构形式和力学性能上适合于夯筑土遗址加固,并与遗址体具有较好的兼容性。     

页岩烧结保温砌块砌体基本力学性能试验研究

通过对页岩烧结保温砌块砌体轴心抗压、沿通缝抗剪、剪压复合抗剪性能试验研究,分析其破坏特征和破坏机理。试验结果表明:页岩烧结保温砌块砌体受压破坏时,在竖向灰缝附近形成主裂缝,接近极限荷载时砌体出现表皮剥落现象;沿通缝抗剪破坏模式主要为单剪破坏,脆性明显;剪压破坏有剪磨、剪压和斜压3种类型;实测轴心抗压强度平均值高于规范值,沿通缝抗剪强度、复合抗剪强度平均值低于计算值,并分别给出砌体轴心抗压强度平均值、抗剪、剪压复合受力抗剪强度平均值建议公式;剪压复合抗剪强度随着压应力的增大而增大;建立了页岩烧结保温砌块砌体受压应力应变关系表达式;给出该类砌块的弹性模量和泊松比的建议值。     

基础尺寸对碎石土地基扩底基础上拔承载力影响的现场试验研究

影响基础上拔承载能力的因素包括地基土物理力学参数及基础尺寸参数,而确定混凝土方量最小、基础上拔承载力最大的基础参数配比是基础优化设计的关键。以戈壁滩碎石土地基中的原状土扩底基础为研究对象,采用正交设计方法,以立柱直径、深宽比、扩展角为影响因素,以基础上拔承载力为分析指标,设计出9组尺寸的足尺基础。通过现场试验,获得了各试验基础的荷载位移曲线和上拔承载力值,提出了采用渐变率的概念表征荷载位移曲线的非线性变化特征,通过分析发现基础荷载位移曲线渐变率与承载能力呈负相关。结合正交试验分析结果,得出立柱直径、深宽比、扩展角3个因素中对碎石土地基原状土扩底基础抗拔承载能力的影响程度由大到小依次为深宽比、立柱直径、扩展角,表明在戈壁滩碎石土地基基础的工程设计中增加深宽比能提高基础抗拔承载能力。     

基于Workbench杏壳力学特性分析

为提高杏核的破壳质量,对杏核壳体的力学性能进行研究。考虑到杏核表面有凸起的棱筋及壳体不同区域厚度不同对力学特性的影响,通过威布三维Reeyee扫描仪对1/2赛买提杏核壳体进行扫描,利用SpaceClaim软件对杏核壳进行模型修复,得出杏核壳体的三维分析模型;运用ANSYS Workbench对1/2杏核壳体进行3种方式加载云图分析,得出最佳的破壳方式,然后通过试验验证模型分析的准确性。结果表明：赛买提杏核沿不同方向施压所需的破碎力有显著差异,其中沿Y 轴方向所需破碎力最大,为856 N,变形量为2.48 mm,杏仁破碎率为0;沿X=Z 轴方向所需破碎力最小,为398 N,变形量为0.41 mm,杏仁破碎率为21.8%;沿X 轴方向施压所需的破碎力为426 N,变形量为1.08 mm,杏仁破碎率为0。验证试验结果与模型分析的结果一致。因此,通过扫描仪建模更能准确反映杏壳的表面特征,相对于Y、X=Z 轴,沿X 轴方向施压更合适。本文可为杏核破壳机械的设计提供参考依据。     

Stability analysis on shallow tunnel with floor lift under inclined ground by upper bound method

采用极限分析上限法,基于内外能耗守恒原理,通过构建考虑隧底隆起的斜坡地段浅埋隧道破坏模式,推导出围岩压力的计算式,并通过典型算例重点分析了典型因素对隧道围岩稳定性的影响。研究结果表明：基于泰沙基极限平衡法进行隧道围岩支护设计较为保守,不考虑隧底隆起的极限分析方法次之考虑隧底隆起极限分析方法的风险最大;斜坡地表倾角增大对浅埋隧道稳定性有着不可忽视的不利影响;围岩压力随岩土侧压力系数减小、埋深增大、断面尺寸加大而增大;岩土黏聚力增大、内摩擦角增大对提高浅埋隧道围岩稳定性有积极作用。     

间作条件下玉米根系固土力原位测定

农作物的根系对土壤的固持作用可以减少坡耕地的水土流失。本研究以云南主要农作物玉米为例,通过采用剪切箱和锚杆拉力计,在玉米的成熟期对单作和与大豆间作2 种种植方式下的玉米根系在10 cm 深度上的固土能力进行了原位测定。结果表明,当施加载荷为1.5 kN 时单作玉米根系位移为5.9 mm,与大豆间作下的玉米根系位移是3.15 mm,裸地的位移是7.26 mm。单作玉米根系滑动距离要明显高于间作玉米根系,说明间作种植模式下的玉米的固持土壤能力要强于单作玉米。     

钢结构仿古建筑双梁柱中节点的受力机理

为研究钢结构仿古建筑双梁柱中节点的抗震性能,对4个全焊双梁柱中节点进行了水平低周反复加载试验。通过观测试件在侧向力作用下的受力过程和破坏形态,分析双梁柱中节点的受力机理。根据梁截面形式的不同,将其分为箱型截面梁与工字型截面梁2类,依据仿古建筑独特的构造特点,将各试件节点核心区划分为上、中、下3个区域。通过量测各区域内的应变大小,分析该类结构节点核心区在侧向力作用下的受理机理及破坏模式,并建立双梁柱节点的斜压杆受力模型。试验结果表明：仿古建筑双梁柱节点的破坏形式主要为沿下核心区对角线的剪切破坏,并通过理论计算分析提出一种考虑轴压比与梁截面形式的双梁柱中节点抗剪承载力修正公式。     

红旗煤矿开采沉陷土地生态服务价值影响

为研究因煤矿地下开采造成的地面沉陷程度及其土地生态服务功能价值影响,首先利用FLAC模型对地面沉陷进行定量预测,根据地面沉陷预测结果基于GIS技术对因地面沉陷造成的土地生态服务价值进行定量分析、估算。研究结果表明：全井田最大下沉值为3 590 mm,最大倾斜值为71.8 mm,最大曲率值为2.18×10-3/m,最大水平变形值为27.3 mm/m,最大水平移动为898 mm,地表沉陷面积为8.09 km2;将导致土地生态服务价值损失537.11万元。     

Analysis of Solid Fluid Coupling for Tunnel Excavation in Complicated Fractured Rock Masses

When tunnels are through water bearing section of fractured rock mass, a complex interaction process between rock mass deformation and fluid transportation is one of the most important reasons for water gushing, water bursting and mud bursting.To study the rock mass deformation and fluid transportation in tunnel excavation under complex geological conditions, a hydraulic model of complex crack rock mass was established from the relationship between the crack growth degree of surrounding rock in deep buried tunnel and the engineering scale, with which fracture network of different levels in rock mass could be considered simultaneously.Furthermore,a computer Fortran program was put forward to simulate the solid fluid coupling of excavation process of a deep buried tunnel.And it was found that the principal fractures had strong flowing action and network fractures had storage function and lag effect in seepage area.And the yield area of surrounding rock was increased under the coupling of seepage field and stress field.     

Study of Tunnel Supporting Effect

Based on the elastic theory, an analysis can be made on stress and plastic deformation under tunnel excavation and shotcrete support.FLAC 3D can be used to simulate the mechanical behavior of excavation and support, getting the deformation of surrounding rock stress and plastic without support and shotcrete. The results show that, the prestress applied on the anchor equals to the supporting force when the tunnel plastic zone disappears. This support improves the self bearing capacity of surrounding rock, effectively suppresses the expansion of the plastic zone after the tunnel excavation, and prevents further damage to the tunnel surrounding rock.     

Analysis of Seismic Dynamic Responses of Tunnel throughFault Zone in High Earthquake Intensity Area

Based on dynamic time history analysis, dynamic response behavior of an un supported tunnel through fault zone which was simulated by interface and solid elements was studied under uniform input earthquake wave excitation. The analyses of response behaviors, including displacement difference, acceleration magnification, and plastic zones and so on, were carried out when earthquake wave excitation was input along transverse, longitudinal and vertical of tunnel respectively. The results show that simulation method for fault zone is effective; the earthquake causes obvious displacement difference at fault zone and surrounding rock contacting part. The maximal displacement difference reaches to 51.8mm under transverse uniform input earthquake wave excitation. And the displacement difference under vertical and longitudinal is only 44.3% and 23.1% of the transverse value, respectively; the acceleration magnification in fault zone is significantly greater than that in surrounding rock. Shear failure zone appears at the fault zone and surrounding rock contacting part, and it is especially prominent under input longitudinal earthquake wave excitation. It is proposed that fault zone has significantly influence on the dynamic performance of tunnel. The fault zone and the transitional zones are the control zones of seismic design when tunnel passes through fault zone, thus, the study on the anti seismic measures should be further strengthened.     

焊接加固热作用对工形截面压弯钢构件承载性能的影响

为研究焊接加固热作用及不同初始负载对工字形压弯钢柱承载性能的影响,基于考虑热影响的热结构耦合分析方法进行了热源模型热输入改进,并考虑初始几何缺陷、初始残余应力及摩擦等,完成了不同负载下焊接加固的3个工字形压弯钢柱的模拟分析。研究了焊接位移时程、腹板应力应变重分布及荷载位移关系,通过有限元分析与相应试验结果对比验证,进而获得了试验无法获得的焊接温度场、翼缘与加固板间的焊接应力应变重分布以及翼缘边缘屈服承载力等结果,并将承载力结果与规范计算结果对比,考察了现有设计方法。结果表明,焊接顺序决定焊接变形的发展过程,焊接热输入和初始负载共同决定持载焊接的位移变化范围和焊接残余变形的大小;初始负载越大,应力应变重分布往偏心受力方向发展更多,承载力越低,而初始残余应力不影响极限承载力;采用考虑热影响的有限元方法具有一定可行性和总体安全性,规范设计方法仍有可提升空间。     

Analysis on Interfacial Stress Between Surrounding Rock and Shotcrete Lining

According to the characteristics of interfacial stress between surrounding rock and shotcrete support, mechanical model of composite curved beame for support system of tunnel surrounding rock and shotcrete lining was established, considering the interfacial deformation coordination and the effects of bearing arch of surrounding rock. Then from static equilibrium of two differential elements, the differential equations for the radial displacement of composite curved beam were obtained. All analytic formulas of both interfacial stress and internal forces between surrounding rock and shotcrete lining by arbitrary distribution load were derived. And thus the mechanical condition of interface zone and the stress concentration position were obtained, which is convenient to assess the stability of surrounding rock and predict the safety. Finally, the analysis of tunnel project excavated by bench method showed that shotcrete lining made the formation of compressive stress zone in surrounding rock by transferring stress from the interface between surrounding rock and shotcrete, which is beneficial to improve the stability of surrounding rock.     

Experimental Research on the Behavior of Direct Anchoring Beam-wider-than-wall Joint

Based on the elastic finite element analysis of the RC beam-wider-than-wall joint, two large-scale specimens of the direct anchoring beam-wider-than-wall joint are designed to test the joint behavior. The stresses and slips of longitudinal bars in the beam, load-bearing capacity and destruction form are observed and analyzed. The analysis and test results show that: The wide beam should be extended through into the wall for some length to make the flexural stress uniform along beam section width, thus the beam's bearing capacity can be achieved. The anchorage condition of the upper longitudinal bar in the beam outside the wall's width is poor, thus the anchorage length prescribed in the current CODE is not enough to ensure the bearing capacity and ductility of joints. The beam stirrups are very important to the anchorage of the upper longitudinal bar in the beam outside the wall's width. If the quantity of the beam stirrups is not enough, the wide beam in the joint area would have more cracks which decrease the bearing capacity and ductility of joints. Finally, a novel spatial truss mechanism model for the beam-wider-than-wall joint is put forward.     

Kolmogorov entropy analysis of surrounding rock system in the processing of unloading for deep buried tunnels

Rock is a kind of physical nonlinear complicated medium, under deep buried condition the surrounding rock system deformation shows geometrical nonlinear characteristic, and the interaction between the two nonlinear mechanism makes the unloading of surrounding rock system evolving complexly. Based on the Lagrangian method and large deformation caculation method, both the double nonlinearity and nonlinear dynamics character of deep buried tunnel surrounding rock system under unloading are studied. The numerical model results show that the Kolmogorov entropy has been extracted from the evolution data in the unloading process of surrounding rock system. The analysis indicates that the typical chaos character has been demonstrated in the process of unloading for deep buried tunnel surrounding system and the rock mass energy dissipation is analyzed at the stage of unloading.     

Testing and modeling studies on creep characters of supports for tunnel using nonlinear constitutive model

Creep characters of tunnel supports structure is analyzed according to triaxial creep test of concrete specimen of deep tunnel supports structure adopting MTS815 hydraulic servo system. The creep parameters of nonlinear creep model are presented based oncreep curve. The finite element numerical model has been established considering tunnel construction process, creep characters of surrounding rock and support structure. The displacement characteristics, the effective stress and the maximum shear stress in different position in primary support and second lining are obtained through creep characters analysis of surrounding rock and supports structure. The features of displacement and stress dependent time of tunnel supports has visible difference comparing with discard creep effect and calculation displacement and practical monitoring results is basic concordance. The creep characters of surrounding rock and tunnel supports should be considered for deep tunnel.