Genotype and Environmental Influences on Pasting Properties of Rice Flour

The pasting behavior of flour from several Australian rice (Oryza sativa L.) cultivars, differing in amylose content and grown in three different locations and three seasons, were determined using the Rapid Visco Analyser. Genotype, growth season, and growth location all affected the pasting behavior of rice flour. The amylose content of the same cultivar was significantly higher in the coolest growing season, resulting in RVA traces with lower peak viscosity and higher setback than samples with lower amylose content. When the same cultivar of rice was grown in different locations in the same season, there were no significant differences in the total starch, protein, lipid, and amylose content of the flour, but there were significant differences in the pasting behavior. This indicates that environmental as well as genetic factors influence the pasting behavior of rice flour. Flour from parboiled and quick‐cooking rice did not paste and had low viscosities compared with unprocessed rice. Results from this study showed that the pasting behavior of rice flour was related to genotype and was influenced by environmental factors that brought about subtle changes in the grains that were not picked up by chemical analyses.     

Effect of Stabilized Rice Bran Fractions on the Formation of Rice Flour Pasting Properties

Rice flour composition played a key role in determining the changes in pasting properties of rice flour. The influence of incorporating defatted rice bran (DFRB), rice bran fiber (RBF), rice bran protein (RBP), and stabilized rice bran (SRB) fractions on the mechanism of rice flour pasting viscosities was investigated. Pasting properties of long‐ and medium‐grain rice flour substituted with 5, 10, 15, 20, and 100% bran fractions resulted in a significant decrease (P < 0.05) in rice flour pasting property values. Flour substituted with RBP had the lowest pasting property measurements compared with other fractions, and the greater the percentage substituted, the lower the pasting property values. DFRB and RBF were least affected properties when used as a replacement. Results were attributed to the contribution of rice starch in the mechanism of rice paste formation, in which decreasing starch in a rice flour sample, as a result of substituting with fractions of SRB, may have resulted in faster swelling of starch granules to the maximum extent and increased their susceptibility to be disrupted by shear, resulting in low paste viscosities. Results also suggested that protein structural integrity and the nature of starch–protein bonding affected rice flour pasting mechanism formation.     

Effect of Storage on Fat Acidity and Pasting Characteristics of Wheat Flour

Two cultivars of wheat (Triticum aestivum L.), Sunco and Sunsoft, were used to study the influence of storage time and temperature on the formation of starch-lipid complexes in flour pastes. Untreated and fat-reduced whole meal flours were stored separately for up to 12 months at 4, 20, and 30°C. The stored samples were analyzed for fat acidity, pasting properties, and iodine binding values. Fat acidity increased significantly in the untreated flour samples stored at 30 and 20°C compared with 4°C. Starch pasting properties, as measured using a Rapid Visco Analyser (RVA) indicated that the final viscosity of untreated flour samples of both cultivars increased significantly with storage time and elevated temperature, and correlated positively with increased fat acidity. Iodine binding values of the RVA pastes decreased with storage time and elevated temperature, and correlated negatively with fat acidity and final viscosity. The fat-reduced Sunco and Sunsoft flours showed less pronounced changes compared with untreated flours, whereas small changes in the RVA parameters were noted in grains stored over 12 months. The results indicate that free fatty acids are released during storage and that they increase the potential for starch-lipid complex formation when stored whole meal wheat flours are pasted in the RVA. These changes were evident after two to three months of storage at 20 and 30°C.     

Pasting Process in Rice Flour Using Rapid Visco Analyser Curves and First Derivatives

The objective of these studies was to gain a better understanding of the pasting process in rice. We chose six different medium grain rice flour samples with amylose contents of 0.41–24.9% and protein contents of 4.89–10.65%. By using the first derivative of Rapid Visco Analyser (RVA) curves, changes in the pasting rates could be obtained. We found that samples containing low amylose contents (CM101 [CA] 0.41% amylose and 7.04% protein) exhibited a single smooth transition during pasting. Pastes from all other samples, M201 (TX), Nato (LA), Koshihikari (CA), Mercury (LA), and Nanking Sel (LA) with higher amylose contents (10.65–24.9%) underwent multiple phase transitions and rate changes before the peak viscosity. Disruption of disulfide linkages using dithiothreitol (DTT) led to a decrease in the rate of the single pasting step observed for CM101 (CA). Rice containing larger concentrations of amylose showed an increase in the first, but a decrease in subsequent steps. Our data suggests that amylopectin and protein are mutually important in the initialization of pasting in rice. At later stages of pasting, amylose and its complexes seem to become important.     

Structures of Four Waxy Rice Starches in Relation to Thermal,Pasting, and Textural Properties

Waxy rice starches from three japonica cultivars (Taichung Waxy 1 [TCW1], Taichung Waxy 70 [TCW70], Tachimemochi) and one indica cultivar (Tainung Sen Waxy 2 [TNSW2]) were characterized for chemical and physicochemical properties. The amylopectin structures were different for the four waxy rice starches in terms of degree of polymerization (DP), average chain length (CL), exterior chain lengths (ECL), and distribution of chains, indicating the existence of varietal differences. The order of swelling power was TCW1 > TCW70 > TNSW2 > Tachimemochi; the order of water solubility index was TCW70 > TNSW2 > Tachimemochi > TCW1. The low water solubility index of TCW1 might be ascribed to a high DP. All starches shared similar gelatinization temperatures and enthalpies but showed distinct retrogradation patterns. TNSW2 showed the highest retrogradation rate, followed by TCW2, Tachimemochi, and TCW70. TCW70 exhibited the highest overall pasting viscosity, followed by TNSW2, TCW1, and Tachimemochi. The hardness of waxy rice starch pastes from a Brabender amyloviscograph increased rapidly after storage at 5°C for one day and remained the same or slightly increased after seven days of storage, whereas the opposite trend was observed for adhesiveness. The lower degree of retrogradation of TCW70 was probably a result of a larger amount of A chain and a shorter ECL. The changes in hardness correlated with the amount of A and B1 chains. The texture attributes of waxy rice starch pastes were significantly affected by amylopectin retrogradation during storage.     

Influence of Early and Delayed Transplantation of Paddy on Physicochemical,Pasting, Cooking,Textural, and Protein Characteristics of Milled Rice

Milled rice of four indica cultivars (PR114, PR116, PR118, and PAU201) obtained from early (June 5 and 15) and delayed (June 25 and July 5) transplanted paddy was evaluated for physicochemical, pasting, cooking, and protein characteristics. During the grain‐filling and development stage, early transplanted paddy experienced average maximum and minimum temperatures of 32.8 and 22.3°C, respectively, against 30.8 and 15°C, respectively, for delayed transplanted paddy. Lightness (L*) value, protein content, and lipid content of milled rice were lower, whereas apparent amylose content, cooked grain hardness, final viscosity, and setback viscosity were higher in the delayed transplanted paddy. Whiteness of milled rice of PR114, PR116, and PR118 from delayed transplanted paddy was lower than milled rice from early transplanted paddy. PAU201 did not show any change in whiteness with delayed transplantation. Cooked rice of PAU201 showed exceptionally higher adhesiveness and lower hardness compared with other cultivars. Protein profiling showed a lower accumulation of prolamines in milled rice from PR114 and PAU201 upon delaying the transplantation from June 5 to July 5, whereas PR116 and PR118 showed a decrease in prolamine accumulation from transplantation on June 25. The changes in milled rice caused by delayed transplanting of paddy might be because of cool nighttime air temperature that affected the accumulation of starch, protein, and lipid.     

Effect of Alkaline‐Soluble Proteins on Pasting Properties of Nonwaxy Rice Flour

The pasting properties of rice flours and reconstituted rice flours from mixing a common starch with proteins extracted from different rice cultivars at different total protein content levels were studied. Results showed that not only the total protein content but also the protein composition had an effect on the pasting properties of the rice flours. Among the different strands of rice proteins, globulin had the strongest influence on the pasting properties, followed by glutelin, whereas prolamin had the least influence. At the subunit level of the proteins, proteins with a molecular weight of 17,000, most likely from globulin, had the strongest effect on the peak viscosity of the rice flour, followed by those of 33,000. In comparison with that of the rice starch, the influence of proteins in rice was limited. The effect of interactions between the rice proteins and the starch, such as the role of starch‐granule‐associated proteins, was not isolated in this study, and further investigation is required to quantify this effect.     

Functional and Digestive Characteristics of Extruded Rice Flour

Waxy (short grain), long grain, and parboiled (long grain) rice flours were extruded using three different temperatures and five different water feed rates. The water absorption and water solubility index of the extrudates was 0.67–5.86 and 86.45–10.03%, respectively. The fat absorption index was similar to that of unextruded flours with an average value of 0.96 g/g ± 0.12. Bulk density decreased with an increase in moisture, except waxy rice, which had a quadratic relationship. The viscosity profiles for long grain and parboiled rice were similar. Both initially increased in viscosity (>130 RVU), then decreased to ≈40 RVU. The final viscosity was ≈60 RVU. Waxy rice viscosity remained low (<20 RVU), then doubled upon cooling. The main difference in the digestion profiles was due to temperature. The flours extruded at 100°C digested significantly slower than those extruded at 125 and 150°C. Significant differences were not detected for a given temperature and moisture (P > 0.05) except for long grain and parboiled rice extruded at 100°C and 15% added moisture (F = 4.48, P = 0.03) and 150°C and 20% added moisture (F = 3.72, P = 0.05). Moisture appeared to have little effect for a given temperature, except when parboiled rice was extruded at 150°C. The digestion rate for 11 and 25% added moisture was significantly less than that for 20% (P ≤ 0.05).     

Effect of Hydrocolloids on Water Absorption of Wheat Flour and Farinograph and Textural Characteristics of Dough

The effect of hydrocolloids addition (0, 25, or 1.5 g/100 g of flour) on water absorption of flour and their influence on dough rheology were analyzed. The influence of guar gum (GG), xanthan gum (XG), high‐methoxyl pectin (P), locust bean gum (LBG), and a 1:1 mixture of locust bean gum and xanthan gum (LBG+XG) on water absorption was tested by different techniques including farinograph water absorption, water imbibing capacity, SDS sedimentation test, and sucrose solvent retention capacity. The rheological behavior was analyzed through the farinograph parameters and texture profile analysis (TPA). Principal component analysis (PCA) was applied to evaluate the behavior of the different mixtures. Absorption values obtained by different methods were increased by XG and LBG+XG addition, particularly at the highest levels (1–1.5%). Flour‐P mixtures showed the lowest absorption. GG‐added mixtures led to the more stable doughs and P to the less stable ones. Addition of NaCl increased stability in all cases. According to TPA, softer and less cohesive doughs than control were obtained when hydrocolloids were added, both in conditions of water availability and water restriction (except for XG and GG at the highest levels). However, when enough water was added, more variation in textural attributes among doughs could be observed by PCA. No remarkable differences compared with the control were observed in the gluten network, as evaluated by scanning electron microscopy. Hydrocolloid incorporation led to rheological changes in dough; the trend and degree of this effect was affected by the amount of water added and the structure and concentration of the hydrocolloid.     

Impact of Rice Flour Cold‐Water‐Soluble Fraction Removal on Gelatinization and Pasting Properties

The influence of the cold‐water‐soluble fraction on gelatinization and pasting properties of rice flour was investigated. The cold‐water‐soluble fraction was removed by water extraction under room temperature. The gelatinization properties of untreated and treated flour were analyzed with a differential scanning calorimeter, and pasting profiles were measured with a rapid viscosity analyzer. The removal of the cold‐water‐soluble fraction resulted in the formation of a loosened starch granule structure, a morphological alteration of protein bodies, a markedly lower gelatinization temperature, and a significantly higher pasting enthalpy. The impact on paste viscosity followed different trends. In some cultivars that had lower endogenous amylase activity, the paste viscosity was greatly reduced by the removal of the cold‐water‐soluble fraction. In others, the higher level of endogenous amylase activity led to more soluble saccharides being released through starch hydrolysis. Removing the soluble fraction caused a remarkable increase in peak viscosity. The overall effect on paste viscosity of removing the cold‐water‐soluble fraction was attributed to multiple factors, involving loosening of the starch granule structure, alteration of morphology of protein bodies, and the release of saccharides by endogenous amylase activity.     

Wheat Starch Effects on the Textural Characteristics of Puffed Brown Rice Cakes

A process was described for creating puffed wheat starch based or hybrid starch and rice snack foods processed in a rice cake puffing machine. Puffed cakes consisting of wheat starch and whole grain brown rice, created by mixing wheat starch beads with brown rice before processing and puffing for 10 sec (cooking time) at 210°C, exhibited greater flexibility and fracture strength than traditional rice cakes. The density of puffed wheat starch cakes decreased with increasing moisture content independent of particle size for particles 0.8–5 mm in diameter. The addition of sucrose and shortening promoted the formation of lower density puffed cakes at lower moistures, while salt had little effect.     

Effect of Different Wheat Classes and Their Flour Milling Streams on Textural Properties of Flour Tortillas

Wheat flour tortillas were made from flour streams of three wheat cultivars: Jagger hard red winter wheat, 4AT-9900 hard white winter wheat, and Ernie soft red winter wheat. Wheat samples were milled on a Miag experimental mill. Twelve flour streams and one straight-grade flour were obtained. Tortillas were made from each flour stream and the straightgrade flour by the hot-press method. Tortilla stretchability and foldability were evaluated by a texture analyzer and six panelists, respectively. Flour protein and water absorption affected tortilla texture. The foldability evaluated by panelists was positively correlated with flour protein content, farinograph water absorption, and damaged starch (P < 0.05). The 2BK and 3BK streams of hard wheat produced tortillas with strong stretchability and good foldability. Middling streams of hard wheat yielded tortillas with lighter color and less stretchability. Under the conditions tested in this study, soft wheat flours were not good for producing flour tortillas.     

Prediction of Specific Japanese Sponge Cake Volume Using Pasting Properties of Flour

In Japanese soft wheat (Triticum aestivum L.) breeding programs, protein content (PC), and specific surface area (SSA) of flour have been used as important factors for the baking quality of Japanese sponge cake. We proposed batter pasting viscosity (BPV) as a parameter to predict the baking quality of Japanese sponge cake. BPV was measured using a Rapid Visco‐Analyser (RVA) with a modified heating profile. Twenty soft wheat samples from the 2006‐07 season and 22 from the 2007‐08 season, including Japanese soft wheat cultivars, advanced breeders' lines, and Western White (WW) imported from the United States, were milled and evaluated for solvent retention capacity (SRC) values of four solvents, batter pasting properties, flour pasting properties, PC, SSA, and specific cake volume (SCV) to investigate their relationships. BPV was the most strongly correlated of the parameters to SCV (r = –0.90, P < 0.001). Stepwise multiple regression analysis selected BPV and minimum viscosity (MV) of flour pasting as significant independent variables to predict SCV (corrected R² = 0.848). The variability in BPV related to cake batter expansion was highly explained by PC and sucrose SRC (corrected R² = 0.854, P < 0.001). MV was correlated to SSA (r = 0.56, P < 0.001) and might be related to the prevention of sponge cake shrinkage during baking.     

Degree of Milling Effects on Rice Pasting Properties

The effects of degree of milling on pasting properties of medium‐grain (cv. Bengal and Orion) and long‐grain rice (cv. Cypress and Kaybonnet) were quantified using a Brabender ViscoAmylograph and a Rapid Visco Analyser. For all the cultivars tested, surface and total lipid contents decreased as the degree of milling increased. The peak viscosities for all rice increased with the degree of milling and the rates of increase were higher for medium‐grain than long‐grain cultivars. Degree of milling did not have a consistent effect on final viscosity for all the cultivars tested.     

Effect of Surfactant Structure on the Pasting Properties of Wheat Flour and Starch Suspensions

Systematic studies were performed on the effect of the surfactant alkyl chain length (10–16 carbon atoms) and the head group charge/structure (anionic, cationic, nonionic) on the pasting properties of wheat flour and starch aqueous suspensions by means of a Rapid Visco Analyser (RVA). An excellent agreement was observed between the effect of surfactants on the onset temperature of the pasting process (PT) and the time to reach peak viscosity (t_peak) of wheat flour and wheat starch suspensions. Moreover, a correlation was found between the effect of different surfactants on these two parameters. With the exception of the cationic surfactants (alkyl trimethyl ammonium bromides), the effect of surfactants (alkyl sulfates, maltosides, monoglycerides, and sucrose esters) was found to be strongly dependent on the surfactant chain length. Shorter chain surfactants (C10–C12) induced an earlier pasting, while longer chain surfactants (C14–C16) had the opposite effect. The effect of surfactants on PT and t_peak of flour suspensions was enlarged when the surfactant concentration was increased from ≈1% to 15% (w/w) on a dry starch basis.     

Rheological Properties of Fermented Rice Flour Gel

To clarify the rheological properties of fermented rice noodle (sour mifen) produced in South China, we studied the mechanical properties of gels made from fermented and nonfermented (control) rice flours using static tensile testing, two-bite testing, and dynamic viscoelastic measurement. Rheological measurement under large deformation showed that retrogradation in fermented rice gel proceeded more slowly than in nonfermented rice gel. Lower hardness and brittleness and higher cohesiveness and resilience (degree of recovery) for gels made from fermented rice flour demonstrated that the gel was less firm but more elastic and flexible. Storage moduli of both types of gel increased with time, but the starch retrogradation was suppressed for fermented rice gel. Fermented rice gel exhibited higher resilience and lower rigidity than nonfermented gel, thus the gel stability improved. The chemical analysis of both starches suggests that the partial hydrolysis of amylopectin occurred during the fermentation process.     

Physicochemical,Textural, and Nutritional Characterization of Mexican Rice Cultivars

The physicochemical properties, textural properties, and starch digestibility of rice cultivars grown in Mexico were evaluated. Variations existed in grain dimensions, and the rice grains were classified as medium, long, and extra long. Huimanguillo had the highest amylose content (30.4%), and A06, A92, A98, and Champoton presented the lowest amylose content (24.3–25.2%). The protein content was 7.1–11.0% and the lipid level was 0.47–1.22% among these Mexican cultivars. Champoton showed the highest temperature and enthalpy of gelatinization, and this with A98, Culiacan, and Huimanguillo had the highest enthalpy of retrogradation. Cotaxtla had the highest pasting peak, setback, and final viscosity. The texture assessment in cooked rice showed that A06 had the highest hardness, and A96 and A98 had the highest stickiness. There was little difference in the rapidly digestible starch, slowly digestible starch, and resistant starch content of tested Mexican rice cultivars. The differences in the physicochemical properties could be used to determine the end use of these Mexican rice cultivars.     

Impact of Proteins on Pasting and Cooking Properties of Nonparboiled and Parboiled Rice

The role of proteins in the pasting and cooking properties of non‐parboiled (npb) and parboiled (pb) rice was tested by means of a reducing agent dithiothreitol (DTT) and a protease (trypsin). DTT increased the swelling power and carbohydrate leaching of flour from npb rice flour but decreased its amylose leaching. Although DTT slightly increased the Rapid Visco Analyser (RVA) viscosity at the initial stages of the pasting process, it decreased RVA viscosity in the further phases of the experiment. Preincubation of flour with a trypsin decreased RVA viscosity along the whole temperature profile. Addition of DTT to the cooking water decreased water absorption and rice hardness and increased leaching of solids during cooking and stickiness of the cooked npb rice. Addition of DTT to the cooking water of flour from pb rice increased swelling power, carbohydrate leaching, and amylose leaching. Addition of DTT also increased RVA viscosity. Preincubation with trypsin had a similar effect but the changes were less pronounced. Addition of DTT increased stickiness of cooked pb rice and increased water absorption and leaching of solids during cooking. Taken together, the results provide evidence for the existence of a protein barrier affecting starch swelling, rheological, and cooking properties of both npb and pb rice.     

Key Proteins Causing Changes in Pasting Properties of Rice During Aging

Key components that cause changes in pasting properties of rice during storage aging were investigated in this work. The main nonstarch components in rice were sequentially removed from fresh and aged rice, the aging effect of the component was separated, and thus the aging contribution rate of the component (CACR) on rice aging could be deduced. The results showed that the largest contributor to rice aging was albumin with a CACR of 65%, followed by globulin and prolamin with the CACRs of 38 and 14%, respectively, and the CACR of glutelin was small (1%). In contrast, the CACRs of fat and crude starch were –7 and –11%, respectively. These findings suggest that albumin and globulin are predominantly responsible for changes in pasting properties of rice during storage aging. This conclusion directs future researchers to the changes occurring in albumin and globulin for disclosing the mechanisms of rice aging.