莲子热风干燥过程对其淀粉热特性及凝胶化的影响

为解决莲子干燥过程中淀粉形态结构变化造成莲子结壳、硬化,不利于干燥以及复水难、易返生问题,该文利用差示扫描量热技术(differential scanning calorimetry,DSC)对新鲜莲子以及不同热风干燥(70、80、90℃)莲子的淀粉热特性与凝胶化过程进行了研究.研究发现,莲子淀粉在低水分环境(42.2%,以质量比计)时存在2个明显的吸热峰,高水分环境(71.1%,以质量比计)时存在1个明显的吸热峰;莲子在干燥过程中不断失水,并伴随着淀粉凝胶化.方差分析(analysis of variance,ANOVA)表明,高温干燥显著影响莲子淀粉的热特性,其淀粉凝胶化温度(峰起温度To、峰顶温度Tp以及峰止温度Te)部分显著升高.相同干燥条件下,莲子淀粉糊化焓ΔH受水分显著影响,但干燥温度、升温速率对其影响不显著(P>0.01).采用Kissinger、Crane方程获得了淀粉凝胶化动力学参数(活化能Ea、指前因子Z以及反应级数n).莲子淀粉的非等温凝胶化反应可近似为一级反应,高温干燥后其Ea值出现增加,并随着水分增加呈现降低趋势.研究结果可为确定莲子高品质干燥工艺以及干莲子、莲子淀粉后续加工过程提供技术支持.     

Effect of sucrose on the thermomechanical behavior of concentrated wheat and waxy corn starch-water preparations

The rheological behavior of concentrated starch preparations from two different origins (wheat and waxy corn) was studied in the presence of sucrose by dynamic mechanical thermal analysis (DMTA). Moisture contents ranged from 30 to 60% (w/w wsb), and samples contained 0, 10, or 20 g of sucrose for 100 g of the starch-water mixture. The storage modulus (G') changes during heating depended strongly on water content (in the moisture range studied), and the importance of these variations was dependent upon the starch type. Sucrose addition resulted in a shift to higher temperatures of the increase in G' during heating. Differential scanning calorimetry (DSC) and electron-spin resonance (ESR) analyses were performed in parallel in order to relate the viscoelastic changes to water migrations and to structural disorganization of starch. Sucrose was found to increase the gelatinization temperature and enthalpy of both starches, implying a stabilization of the granular structure during heating. The sugar-water interactions do not appear to be the only way by which sucrose delays starch gelatinization. The obtained results suggest that sugar-starch interactions in the amorphous and/or the crystalline regions of the starch granules should be envisaged.     

Thermal Modifications of Starch During High‐Temperature Drying of Pasta

Changes in starch at the molecular level during high‐temperature (HT) drying of pasta were studied with differential scanning calorimetry (DSC). Pasta was manufactured from durum wheat semolina into the shape of spaghetti on a pilot‐plant installation. The HT phase (100°C) was applied at relatively high (27 g/100 g, wb), intermediate (20 g/100 g), and low (15 g/100 g) product moisture, respectively. Spaghetti dried at 55°C served as reference samples. The changes in the thermal properties of starch during drying were dependent on the drying conditions. The gelatinization enthalpy of pasta dried at 55°C was reduced by 30% during drying, which indicates a partial melting of the starch crystallites. With the beginning of the HT phase, the gelatinization enthalpy increased to final values that were close to or higher than those of freshly extruded pasta. In general, HT drying of pasta induced a broadening of the gelatinization range. Starch crystallinity remained unchanged during extrusion and drying at HT. Based on a state diagram of starch and on DSC measurements of pasta during drying, it is hypothesized that HT drying favors molecular rearrangements of starch polymers at the double helical level.     

Morphological, structural, thermal, and rheological characteristics of starches separated from apples of different cultivars

The starches were separated from unripe apples of five cultivars (Criterion, Ruspippum, Red Spur, Skyline Supreme, and Granny Smith) and evaluated using scanning electron microscopy (SEM), gel permeation chromatography (GPC), X-ray diffraction, differential scanning calorimetry (DSC), and dynamic viscoelasticity. SEM showed the presence of round granules as well as granules that had been partially degraded, probably by amylases. The starch granules in different apple starches ranged between 4.1 and 12.0 mum. Debranching of starch with isoamylase and subsequent fractionation of debranched materials by GPC revealed the presence of an apparent amylose, an intermediate fraction (mixture of amylose and amylopectin), long side chains of amylopectin, and short side chains of amylopectin in the range of 28-35.2, 3.6-4.4, 20-21.3, and 39.9-47.1%, respectively. The swelling power of starches ranged between 14.4 and 21.3 g/g. X-ray diffraction of apple starches showed a mixture of A- and B-type patterns. All apple starches showed peak intensities lower than that observed for normal corn and potato starch, indicating the lower crystallinity. The transition temperatures (onset temperature, T(o); peak temperature, T(p); and conclusion temperature, T(c)) and enthalpy of gelatinization (deltaH(gel)) determined using DSC ranged between 54.7 and 56.2 degrees C, between 57.1 and 59.1 degrees C, between 60.2 and 63.5 degrees C, and between 3.3 and 4.2 J/g, respectively. The viscoelastic properties of starch from different cultivars measured during heating and cooling using a rheometer differed significantly. Red Spur and Criterion starches with larger granule size showed higher G' and G' ' values, whereas those containing smaller size and amylolytically degraded granules showed lower G' and G' '.     

Cross‐Linked Resistant Starch: Preparation and Properties

Resistant starches (RS) were prepared by phosphorylation of wheat, waxy wheat, corn, waxy corn, high‐amylose corn, oat, rice, tapioca, mung bean, banana, and potato starches in aqueous slurry (≈33% starch solids, w/w) with 1–19% (starch basis) of a 99:1 (w/w) mixture of sodium trimetaphosphate (STMP) and sodium tripolyphosphate (STPP) at pH 10.5–12.3 and 25–70°C for 0.5–24 hr with sodium sulfate or sodium chloride at 0–20% (starch basis). The RS₄ products contain ≤100% dietary fiber when assayed with the total dietary fiber method of the Association of Official Analytical Chemists (AOAC). In vitro digestion of four RS₄ wheat starches showed they contained 13–22% slowly digestible starch (SDS) and 36–66% RS. However after gelatinization, RS levels fell by 7–25% of ungelatinized levels, while SDS levels remained nearly the same. The cross‐linked RS₄ starches were distinguished from native starches by elevated phosphorus levels, low swelling powers (≈3g/g) at 95°C, insolubilities (<1%) in 1M potassium hydroxide or 95% dimethyl sulfoxide, and increased temperatures and decreased enthalpies of gelatinization measured by differential scanning calorimetry.     

Retrogradation of Maize Starch After Thermal Treatment Within and Above the Gelatinization Temperature Range

Studies of starch retrogradation have not considered the initial thermal treatment. In this article, we explore the effect of heating to temperatures within and above the gelatinization range on maize starch retrogradation. In the first experiment, 30% suspensions of waxy (wx) starch were initially heated to final temperatures ranging from 54 to 72°C and held for 20 min. On reheating in the differential scanning calorimeter immediately after cooling, the residual gelatinization endotherm peak temperature increased, the endotherm narrowed, and enthalpy decreased. Samples stored for seven days at 4°C showed additional amylopectin retrogradation endotherms. Retrogradation increased dramatically as initial holding temperature increased from 60 to 72°C. In a second experiment, wx starch was initially heated to final temperatures from 54 to 180°C and rapidly cooled, followed by immediate reheating or storage at 4°C. Maximum amylopectin retrogradation enthalpy after storage was observed for initial heating to 82°C. Above 82°C, retrogradation enthalpy decreased as initial heating temperature increased. A similar effect for ae wx starch was observed, except that retrogradation occurred more rapidly than for wx starch. These experiments show that heating to various temperatures above the range of gelatinization may profoundly affect amylopectin retrogradation, perhaps due to varying extents of residual molecular order in starch materials that are commonly presumed to be fully gelatinized. This article shows that studies of starch retrogradation should take into account the thermal history of the samples even for temperatures above the gelatinization temperature range.     

Physicochemical and Structural Characteristics of Flours and Starches from Waxy and Nonwaxy Wheats

A waxy spring wheat (Triticum aestivum L.) genotype was fractionated into flour and starch by roller and wet‐milling, respectively. The resultant flour and starch were evaluated for end‐use properties and compared with their counterparts from hard and soft wheats and with commercial waxy and nonwaxy corn (Zea mays L.) starches. The waxy wheat flour had exceptionally high levels of water absorption and peak viscosity compared with hard or soft wheat flour. The flour formed an intermediate‐strength dough that developed rapidly and was relatively susceptible to mixing. Analysis by differential scanning calorimetry and X‐ray diffractometry showed waxy wheat starch had higher gelatinization temperatures, a greater degree of crystallization, and an absence of an amylose‐lipid complex compared with nonwaxy wheat. Waxy wheat and corn starches showed greater refrigeration and freeze‐thaw stabilities than did nonwaxy starches as demonstrated by syneresis tests. They were also similar in pasting properties, but waxy wheat starch required lower temperature and enthalpy to gelatinize. The results show analogies between waxy wheat and waxy corn starches, but waxy wheat flour was distinct from hard or soft wheat flour in pasting and mixing properties.     

Thermal Properties of Corn Starch Extraction Intermediates by Differential Scanning Calorimetry

Thermal properties of corn starch extraction intermediates from four types of corn were studied using differential scanning calorimetry. Starch at four different stages of extraction, including a standard single-kernel starch isolation procedure and three starch extraction intermediates, was isolated from mature corn kernels of B73 and Oh43 inbreds and the mutants of waxy (wx) and amylose extender (ae) in an Oh43 background. Differences in thermal properties and moisture and protein contents of starch from the extraction stages were statistically analyzed. Most thermal properties (gelatinization and retrogradation onset temperatures, gelatinization and retrogradation ranges, gelatinization and retrogradation peak temperatures, gelatinization and retrogradation enthalpies, peak height index, and percentage of retrogradation) of starches extracted at stage 3 intermediate (a procedure that did not include a final washing step) were similar to those of starch extracted by the standard single-kernel isolation procedure. Values for gelatinization peak temperature, gelatinization enthalpy, and peak height index were different between the standard and the stage 3 intermediate. The values obtained from starches extracted at stage 3, however, were consistent and predictable, suggesting that this extraction intermediate might be used in screening programs in which many starch samples are evaluated. By using the stage 3 extraction, samples could be evaluated in three rather than four days and the procedure saved ≈0.5 hr of labor time. The other two starch extraction intermediates, which excluded filtering and washing or filtering, washing, and steeping, produced starch with thermal properties generally significantly different from starch extracted by the standard single-kernel isolation procedure.     

Restriction of Starch Granule Swelling by Iodine During Heating

Differences in the degree of starch granule swelling and granule morphology are shown as a function of iodine concentration during heating. The observations reveal a restriction and delay in wheat and corn starch swelling in presence of iodine (0.02%) and a lack of swelling at higher iodine concentration (0.2%). The presence of iodine during heating did not influence waxy corn starch granule swelling, even at the higher concentration. A delay in the increase in paste viscosity during heating was observed, and gel formation was precluded after cooling at the higher iodine concentration. Waxy corn starch pastes formed a weak gel even at the higher iodine concentration. Spectrophotometric analyses showed that polymers leach into the solution when heated in the presence of 0.02% iodine, while no leaching was observed at 0.2% iodine concentration. Furthermore, the length and the amount of polymers leaching from normal corn were different from that observed for wheat starch. Thermal analyses reveal a shift in the onset of gelatinization temperature and an increase in the enthalpy in the amylose‐lipid region of the endotherm. While the iodine‐polymer complex did not appear to exhibit an endotherm during heating, the granules exhibited a diffused polarized cross, suggesting the presence of an ordered complex.     

Two- and multi-step annealing of cereal starches in relation to gelatinization

Two- and multi-step annealing experiments were designed to determine how much gelatinization temperature of waxy rice, waxy barley, and wheat starches could be increased without causing a decrease in gelatinization enthalpy or a decline in X-ray crystallinity. A mixture of starch and excess water was heated in a differential scanning calorimeter (DSC) pan to a specific temperature and maintained there for 0.5-48 h. The experimental approach was first to anneal a starch at a low temperature so that the gelatinization temperature of the starch was increased without causing a decrease in gelatinization enthalpy. The annealing temperature was then raised, but still was kept below the onset gelatinization temperature of the previously annealed starch. When a second- or third-step annealing temperature was high enough, it caused a decrease in crystallinity, even though the holding temperature remained below the onset gelatinization temperature of the previously annealed starch. These results support that gelatinization is a nonequilibrium process and that dissociation of double helices is driven by the swelling of amorphous regions. Small-scale starch slurry annealing was also performed and confirmed the annealing results conducted in DSC pans. A three-phase model of a starch granule, a mobile amorphous phase, a rigid amorphous phase, and a crystalline phase, was used to interpret the annealing results. Annealing seems to be an interplay between a more efficient packing of crystallites in starch granules and swelling of plasticized amorphous regions. There is always a temperature ceiling that can be used to anneal a starch without causing a decrease in crystallinity. That temperature ceiling is starch-specific, dependent on the structure of a starch, and is lower than the original onset gelatinization of a starch.     

Comparison of Physicochemical Properties and Structures of Sugary‐2 Cornstarch with Normal and Waxy Cultivars

Starches from normal, waxy, and sugary‐2 (su2) corn kernels were isolated, and their structures and properties determined. The total lipid contents of normal, waxy, and su2 corn starches were 0.84, 0.00, and 1.61%, respectively. Scanning electron micrographs showed that normal and waxy corn starch granules were spherical or angular in shape with smooth surfaces. The su2 starch granules consisted of lobes that resembled starch mutants deficient in soluble starch synthases. Normal and waxy corn starches displayed A‐type X‐ray patterns. The su2 starch showed a weak A‐type pattern. The chain‐length distributions of normal, waxy, and su2 debranched amylopectins showed the first peak chain length at DP (degree of polymerization) 13, 14, and 13, respectively; second peak chain length at DP 45, 49, and 49, respectively; and highest detectable DP of 80, 72, and 76, respectively. The su2 amylopectin showed a higher percentage of chains with DP 6–12 (22.2%) than normal (15.0%) and waxy (14.6%) amylopectins. The absolute amylose content of normal, waxy, and su2 starches was 18.8, 0.0, and 27.3%, respectively. Gel‐permeation profiles of su2 corn starch displayed a considerable amount of intermediate components. The su2 corn starch displayed lower gelatinization temperature, enthalpy change, and viscosity; a significantly higher enthalpy change for melting of amylose‐lipid complex; and lower melting temperature and enthalpy change for retrograded starch than did normal and waxy corn starches. The initial rate of hydrolysis (3 hr) of the corn starches followed the order su2 > waxy > normal corn. Waxy and su2 starches were hydrolyzed to the same extent, which was higher than normal starch after a 72‐hr hydrolysis period.     

Physicochemical Properties of Rice Starch Modified by Hydrothermal Treatments

Rice starches of long grain and waxy cultivars were annealed (ANN) in excess water at 50°C for 4 hr. They were also modified under heat-moisture treatment (HMT) conditions at 110°C with various moisture contents (20, 30, and 40%) for 8 hr. The modified products were analyzed by rapid-viscosity analysis (RVA), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). Generally, these hydrothermal treatments altered the pasting and gelling properties of rice starch, resulting in lower viscosity peak heights, lower setbacks, and greater swelling consistency. The modified starch showed increased gelatinization temperatures and narrower gelatinization temperature ranges on ANN or broader ones on HMT. The effects were more pronounced for HMT than for ANN. Also, the typical A-type XRD pattern for rice starch remained unchanged after ANN or HMT at low moisture contents, and the amorphous content increased after HMT at 40% moisture content.     

Quality,Decontamination, and Energy Use Considerations During Radiant‐Heat and Tempering Treatments of Shelled Corn

Infrared (IR) heating of corn followed by tempering treatments has potential to decontaminate corn of microbes without adverse effects on the overall corn quality. However, it is vital to determine the optimal processing parameters that maximize throughput and microbial load reduction and minimize drying energy without affecting overall corn quality. This study investigated effects of IR heating and tempering treatments on mold load reduction, corn color change, and drying energy requirements. Freshly harvested corn samples with initial moisture contents (IMCs) of 20, 24, and 28% wet basis were dried with a laboratory‐scale IR batch dryer in one and two drying passes. The dried samples were then tempered for 2, 4, and 6 h at 50, 70, and 90°C. Results showed that mold load reduction ranged from 1 to 3.8 log colony forming units per gram of corn (log CFU/g) for one‐pass treatments and from 0.8 to 4.4 log CFU/g for two‐pass treatments as tempering temperature and tempering duration increased. Compared with the control, treatments resulted in reduction of the corn color parameter (ΔE ) (P < 0.05). Energy expended to dry the corn varied between 1.7 and 2.5 MJ/kg for one‐pass treatments and between 4.1 and 6.1 MJ/kg for two‐pass treatments. This work showed that IR heating of corn has the potential to significantly decontaminate microbes on corn. The IR process may help producers combat mycotoxin issues in corn that result from mold contamination.     

Influence of Amylose Content on Properties of Wheat Starch and Breadmaking Quality of Starch and Gluten Blends

The effects of amylose content on thermal properties of starches, dough rheology, and bread staling were investigated using starch of waxy and regular wheat genotypes. As the amylose content of starch blends decreased from 24 to 0%, the gelatinization enthalpy increased from 10.5 to 15.3 J/g and retrogradation enthalpy after 96 hr of storage at 4°C decreased from 2.2 to 0 J/g. Mixograph water absorption of starch and gluten blends increased as the amylose content decreased. Generally, lower rheofermentometer dough height, higher gas production, and a lower gas retention coefficient were observed in starch and gluten blends with 12 or 18% amylose content compared with the regular starch and gluten blend. Bread baked from starch and gluten blends exhibited a more porous crumb structure with increased loaf volume as amylose content in the starch decreased. Bread from starch and gluten blends with amylose content of 19.2–21.6% exhibited similar crumb structure to that of bread with regular wheat starch which contained 24% amylose. Crumb moisture content was similar at 5 hr after baking but higher in bread with waxy starch than in bread without waxy starch after seven days of storage at 4°C. Bread with 10% waxy wheat starch exhibited lower crumb hardness values compared with bread without waxy wheat starch. Higher retrogradation enthalpy values were observed in breads containing waxy wheat starch (4.56 J/g at 18% amylose and 5.43 J/g at 12% amylose) compared with breads containing regular wheat starch (3.82 J/g at 24% amylose).     

Influence of Milk,Corn Starch,and Baking Conditions on the Starch Digestibility,Gelatinization, and Fracture Stress of Biscuits

Dough for nontraditional semisweet biscuits—prepared with wheat flour or replacing part of the wheat flour with corn starch, with or without skim milk—was baked at two oven temperatures, 120 or 170°C, until reaching moisture content and water activity lower than 6% and 0.5, respectively. Assays of fracture stress, differential scanning calorimetry, X‐ray diffraction, and starch digestibility were performed. Results showed that biscuits containing milk had the highest fracture stress, and biscuits baked at low temperature were harder than biscuits baked at high temperature. The degree of starch gelatinization during baking was higher when dough was baked at 170°C, compared with dough baked at 120°C. The decrease in gelatinization coincides with the decrease in the height and surface of peaks at 15 and 23° in the X‐ray diffraction patterns. Milk and corn starch did not affect the starch digestibility of biscuits, but biscuits baked at 170°C presented lower fracture stress and higher starch digestibility than biscuits baked at 120°C.     

Evaluation of the Displacement Value as a Method to Detect Reduced Corn Wet-Milling Quality

A procedure based on the resistance and capacitance (RC) properties of corn to calculate a displacement value (DV) was evaluated for detection of corn that had reduced wet-milling quality. In 1991 and 1992, three hybrids were dried at air temperatures between ambient and 115°C in batch dryers. Additional samples, obtained from commercial elevators in 1992, had been dried with air temperatures ranging from 52 to 136°C. A baseline reference relationship was developed between log₁₀-resistance and capacitance with data from ambient-dried samples. A DV was defined as the horizontal distance along the capacitance axis from a sample RC data point to the baseline reference. RC properties of samples dried at air temperatures >50°C were compared to the baseline and the DV determined. Selected drying treatments were wet-milled by a laboratory-scale procedure to verify milling quality and correlation with DV. The effects attributed to hybrid and harvest moisture content on the RC properties of ambient-dried samples were small, allowing the baseline reference to be applied to a wide range of corn samples. In 1992, the baseline shifted upward from the 1991 baseline by 0.5 units on the log₁₀-resistance axis. DV increased significantly at drying air temperatures >50°C for batchdried samples. While DV correlated with drying temperature in batchdried samples (r = 0.66), it did not correlate with starch yield or recovery of commercial samples (r ≤0.10). Although the specific causes could not be determined, the shift in the baseline indicates the method would be difficult to implement on a practical scale. Although not indicated by DV, starch recovery decreased significantly for samples batch-dried at air temperatures ≥70°C. All samples dried at 115–136° had significantly lower starch recoveries.     

Impact of Soaking and Drying Conditions on Rice Chalkiness as Revealed by Scanning Electron Microscopy

Chalkiness is one of the most influential factors on head rice yield. Parboiling is known to be an effective way to remove chalkiness and improve head rice yield. However, the steps involved in the removal of chalkiness are still not completely resolved. This study investigated the effects of soaking temperature, soaking duration, and drying conditions on the removal of rice chalkiness. Chalky brown rice kernels were selected and soaked at 25, 65, 70, or 75°C for 3 h. After 1, 2, or 3 h, the rice samples were frozen before drying or immediately dried. Soaking at 25°C did not remove chalkiness and caused no morphological change in starch granules. When the soaking temperature increased from 25 to 65, 70, and 75°C, the chalkiness decreased from 100% to 34.1, 29.7, and 15.9%, respectively. Soaking rice at temperatures above the starch glass transition temperature but below the gelatinization temperature reduced chalkiness owing to rearrangement of starch granules and protein denaturation to fill the void spaces in the chalky area. During soaking, the morphology of starch granules also changed from round to angular in shape. Drying at temperatures above the starch glass transition temperature also facilitated rearrangement of starch granules to further reduce rice chalkiness.     

Effects of Modulated Differential Scanning Calorimetry (MDSC) Variables on Thermodynamic and Kinetic Characteristics During Gelatinization of Waxy Rice Starch

The total, reversing, and nonreversing thermal properties during gelatinization of waxy rice starch (starch-to-water ratio = 1:2, w/w) were examined by modulated differential scanning calorimetry (MDSC). The effect of MDSC operating variables (i.e., the amplitude and frequency of temperature modulation and the underlying heating rate) on these thermal properties was determined by response surface methodology (RSM) and statistical analysis. The frequency of temperature modulation and the underlying heating rate significantly influenced the gelatinization temperatures and enthalpy changes in total and nonreversing endotherms. In addition, the combination of 0.025Hz and 4–8°C/min with a properly low degree of oscillation was suitable for characterization of starch gelatinization by MDSC. The enthalpy changes in the reversing (thermodynamic) endotherms increased, but those in the nonreversing (kinetic) endotherms decreased with increasing periods (i.e., decreasing frequencies) and underlying heating rates. However, the total enthalpy changes were only slightly influenced by the MDSC variables studied. In addition, the activation energies for the total and nonreversing events were 281.8–417.3 and 386.3–739.7 kJ/mol, respectively, depending on the MDSC conditions. From the compensation relationship between the activation energy and frequency factor, we concluded that the total and nonreversing endotherms were linked to the same single transition.     

Physicochemical Properties of Zero Amylose Hull-less Barley Starch

Zero amylose starch isolated from hull-less barley (HB) showed a typical A-type diffraction pattern. The X-ray analysis suggested that granules of zero amylose (SB94794) and 5% amylose (CDC Candle) HB starches had lower crystallinity than did commercial waxy corn starch. Differential scanning calorimetry showed lower transition temperatures and endothermal enthalpies for the HB starches than for the waxy corn starch. The zero amylose HB starch showed a Brabender pasting curve similar to that of waxy corn starch, but with lower pasting and peak temperatures and a higher peak viscosity. Noteworthy characteristics of zero amylose HB starch were its low pasting temperature and high paste clarity and freezethaw stability, which make this starch useful for many food and industrial applications.     

Preparation and Properties of Starch Phosphates Using Waxy,Common, and High‐Amylose Corn Starches. I. Oven‐Heating Method

The structure and physicochemical properties of waxy, common, and high‐amylose corn starch phosphates prepared by oven heating were studied. Starch phosphates prepared by either slurry or dry‐mixing treatment before oven heating were also compared. The slurry treatment more efficiently incorporated phosphorus into starch relative to the dry‐mixing treatment under the reaction conditions studied. In general, the phosphorylated starch prepared by the slurry treatment exhibited a lower gelatinization temperature, a higher peak viscosity, a lesser degree of retrogradation, and improved freeze‐thaw stability compared with those prepared by the dry‐mixing treatment. Phosphorylation occurred probably in both amylose and amylopectin, and the amount and location of incorporated phosphate groups varied with starch types likely due to their different amylose and amylopectin contents. Waxy starch was more prone to phosphorylation, followed by common and high‐amylose starches, respectively.