Study on drying rate in contact drying with flexible screen

IntroductionA new type contact dryer with non-metal flexibleplaten was patented in 1998 in China, which specialstructure and material solved the problem of low productivity in platen drying. The machine was similar tohot press. Direct contact betWeen wood and heatedplaten allows rapid heat transfer by conduction (Sandoe 1983). Though the flexible screen conducts heatslower than metal platen does, it transfers massmuch fast6r. So water removing rate decides veneerdrying rate in the new machin…     

Simultaneous drying and densification of silver birch (Betula pendula L.) veneers: analysis of morphology,thickness swelling,and density profile

In this study, birch (Betula pendula L.) veneers were simultaneously densified and dried using a contact drying method at pressures of 1.5 and 3 MPa at 130 °C and compared with veneer dried in a laboratory-scale convective type dryer. Compression rate, thickness swelling, and the density profiles of the veneers were investigated. Furthermore, the microstructure of densified veneers was studied by scanning electron microscopy (SEM). A maximum veneer compression rate of 9 % was achieved at a pressure of 3 MPa. Under these conditions, the veneers were, on average, densified from 504 to 574 kg m^?3 (approximately 14 %). After water soaking, full set-recovery—recovery to the initial thickness—occurred. However, the swelling rate was lower for the densified veneer. Density profiles measurements showed that densification occurs throughout the veneers. The SEM images showed that the surface of the densified veneers were smoother, whilst no cracks were detected due to densification. Densification seemed to occur in vessels. Typically, rays were bent when there was a vessel nearby.     

Productive test of a newly drying technology of veneer： intermittent-contact drying of veneer with flexible screen belt

A newly drying technology, intermittent-contact drying of veneer with flexible screen belt (ICD-fbs), was invented and used in poplar veneer drying. Productive test was carried out for validating the practical use of this drying method. The test result shows that to dispose flexible screen belts on the two sides of hot board could help steam discharge remarkably. The veneer dried using ICD-fsb method had smooth and level surface, less deformation and warping, even moisture content, and high utilization rate. The time for opening hot board to discharge steam,which, early or late, is a key to obtain good drying result, was determined at the time when the core‘s temperature of veneer reaches 100℃ (vaporization). Using ICD-fsb method, the shrinking rates in tangent of veneer were from 1.90% to 2.26% for veneer of 0.4 mm in thickness,2.49% to 4.50% for veneer of 1 mm in thickness and 1.34% to 3.30% for veneer of 1.7 mm in thickness, which are much lower than the results obtained by other drying methods. The method of ICD-fsb offers a reliable technological guarantee for solving the deformation problem of veneer drying, especially the deformation of wood from quick-growing plantation.     

Prediction of the optimum veneer drying temperature for good bonding in plywood manufacturing by means of artificial neural network

Veneer drying is one of the most important stages in the manufacturing of veneer-based composites such as plywood and laminated veneer lumber. Due to the high drying costs, increased temperatures are being used commonly in plywood industry to reduce the overall drying time and increase capacity. However, high drying temperatures can alter some physical, mechanical and chemical characteristics of wood and cause some drying-related defects. In this study, it was attempted to predict the optimum drying temperature for beech and spruce veneers via artificial neural network modeling for optimum bonding. Therefore, bonding shear strength values of plywood panels manufactured from beech and spruce veneers dried at temperatures of 20, 110, 150 and 180 °C were obtained experimentally. Then, the intermediate bond strength values based on veneer drying temperatures were predicted by artificial neural network modeling, and the values not measured experimentally were evaluated. The optimum drying temperature values that yielded the highest bonding strength were obtained as 169 °C for urea formaldehyde and 125 °C for phenol formaldehyde adhesive in beech plywood panels, while 162 °C for urea formaldehyde and 151 °C for phenol formaldehyde in spruce plywood panels.     

Dimensional stabilization of compressed laminated veneer lumber by hot pressing in an airtight frame

Abstract

The purpose of this study was to evaluate the dimensional stability and strength properties of compressed laminated veneer lumber (LVL) produced using a closed hot pressing system. LVL specimens were produced with varying number of veneers using either diphenylmethane diisocyanate (MDI) or a water-soluble phenol formaldehyde (PF) resin at varying temperatures (160–200°C), pressures (0.5–3 MPa) and hot-pressing times (2–16 min). Results show that the heating process decreases the recovery of compressive deformation in the veneers when subjected to cyclic moisture and heat conditions. Thickness swelling was approximately 5% after a drying, wetting and boiling cyclic test for LVL using the MDI resin and hot pressed at 200°C for 8 min. Modulus of elasticity and rupture increased for samples produced in both an open press and the closed press with an increase in the number of veneers and density, as did the absorbed energy in impact bending.     

Ultrasound-associated extraction of seed oil of Korean pine

Experiment on ultrasound- associated extraction of seed oil of Korean pine (Pinus koraiensis) was conducted in Northeast Forestry University, Harbin, China. The factors affecting extraction yield, such as ultrasonic frequency, extracting temperature, extracting time and the ratio of material to liquid (ratio of Korean pine seed to absolute alcohol), were analyzed under specific condition and the optimal extracting parameters were obtained as the ultrasonic frequency 32 000 Hz, the extracting temperature 80℃, the extracting time 50 rain, and the ratio of material to liquid 1: 30. The study demonstrates that ultrasound is a reliable and great efficiency tool for the fast extraction of Korean pine seed oil。     

Surface quality sensing of trembling aspen (Populus tremuloides Michx.) veneer products by near infrared spectroscopy

Abstract

The potential of near infrared spectroscopy (NIRS) to estimate wood moisture content (MC), surface energy characteristics and adhesive bond strength were evaluated on aspen (Populus tremuloides Michx.) veneer subjected to different drying times. For samples dried progressively at 103°C, the best MC prediction model was for the total MC range (0–100%) with an R² value of 0.68. However, exposure at 180°C produced surface colour changes, and the CIE L*a*b* colour parameters measuring colour changes were better estimated using the 400–900 nm spectral data than the 1100–2400 nm spectral data. Increased exposure time at 180°C resulted in lower wettability and, hence, larger contact angles, especially when ethylene glycol was used as probe solvent. Lap shear strength tests on veneers showed that adhesion by phenol formaldehyde resins was impaired by the high temperature exposure; however, the lap shear strength test had high variability so there was not always a clear relationship between contact angle and lap shear strength test.     

Wood drying process: impact on Scots pine lumber durability

There are indications that the drying process may have negative effects on the natural durability of wood. The impact of various drying processes on the durability of Scots pine lumber has been evaluated with mass loss in a decay test with brown rot fungus, Coniophora puteana, as measure of the decay resistance of sapwood and inner and outer heartwood. Drying with or without steam conditioning was performed in six different series: air drying, kiln drying at temperature ranges commonly used in Swedish sawmills at 70°C and 90°C with two different regulation principles, and one high-temperature drying at 110°C. Durability varied considerably both between and within boards. Sapwood showed considerable less durability than heartwood. No difference in durability was found between inner heartwood and outer heartwood. Air-dried heartwood showed the highest durability compared to other drying series. The lowest durability in sapwood and heartwood was found for series dried at the 90°C temperature level with high material temperature early in drying. The interpretation is that the duration of high material temperature at high moisture content (MC) is the critical combination for decay resistance in heartwood. Steam conditioning after drying decreased durability in sapwood.     

Imbibitions, energy test and accelerated ageing in primed and non-primed seeds of Peltophorum dubium

Peltophorum dubium seeds were set to imbibe with four treatments, soaked with solution Captan 0.2% under 10and 27℃,PEG 6000 -1.0 MPa under 10 and 27℃. For each treatment there were four replicates with 40 seeds incubated in 9-cm Petri dishes with double filter paper moistened with testing solution. The imbibition curves showed that the final weight increase were from 70% to 150% in the treatments when imbibition entered a lag phase. Seeds were tested for effects on germination of five treatments: control group (nonprimed), primed with PEG6000 -1.0 MPa at 10 and 27℃, primed with Captan 0.2% at 10 and 27℃. For each treatment, there were three sub-treatments: seeds were soaked in distilled water for 12, 24 and 36h before the energy test. Germination percentages of nonprimed seeds and primed in PEG 27℃ soaked in distilled water during 12 h were the highest, reaching 100%. The lowest germination percentage occurred primed seeds with PEG6000 27℃ and soaked in distilled water during 36 h, which was only 52%. Germination mean time of primed seeds in PEG at 10℃, soaked 24 h was 1.08 days, mean time of primed seeds in PEG at 27℃ soaked 12 h was 2.42 days. Accelerated ageing results showed low or no germination after ageing 72 h. Control group had a higher germination percentage and seeds were more resistant to deterioration than those in primed groups, both in Petri dish (27℃) and vermiculate (room temperature).     

Alkaloid variations in Catharanthus roseus seedlings treated by different temperatures in short term and long term

A study was conducted to investigate the effects of high temperature on variations of alkaloid metabolism in C. roseus seedlings in Key Laboratory of Forest Plant Ecology, Northeast Forestry University, Heilongiang, China. 60-day-old C. roseus seedlings with 3-4 pairs of leaves were incubated in chambers with temperature of 30℃ and 40℃for short-term heat shock experiment and 20℃, 25℃ and 35℃ for long-term experiment. The contents of vindoline, catharanthine, vinblastine and vincristine in C. roseus leaves and root were checked at different temperatures in short term （1-6 h） and long term （1-16 d）. Results showed that under short-term heat shock, the contents of vindoline, catharanthine and vinblastine in leaves of the seedlings were higher at 40℃ than at 30℃, but after 6 h treatment, the contents of vindoline and catharanthine under the two temperatures came to the same level. Catharanthine was exclusively distributed in C. roseus roots and its content was increased by 40% after two hours incubation at 40℃, while increased slowly at 30℃ incubation and reached the highest value at 6 h. In the Long-term experiment, concentrations of monomeric alkaloids catharanthine and vindoline were higher at 20℃ than at 25℃ and had a sharp increase under the condition of 35℃. While for dimeric alkaloid, it showed that the higher the temperature, the earlier the peak value of vinblastine content appears. Vincristine had a continuous enhancement and attained 0.027 mg.g^-1 at 16th day under 35℃ condition which was higher than those in the other conditions. It was concluded that high temperature could promote the accumulation of different alkaloids in C. roseus and the accumulation characteristic is highly related to treatment time.     

超声波辅助提取脱脂红松仁中水溶性多糖的研究

采用超声波辅助提取法对脱脂红松仁中水溶性粗多糖的提取工艺进行了研究.通过正交试验,分别考察了提取温度、液料比、提取时间及醇沉浓度4个因素对红松仁多糖提取率的影响,得出优化的工艺条件：提取温度为70℃,液料比为20：1,提取时间为40 min,醇沉浓度为80%,此条件下多糖的提取率为3.65%,平均含量为45.38%.结果表明,超声波辅助提取的效率和含量均优于传统热水浸提法,且具有提取温度低、时间短及效率高的优势.     

Optimizing SSR-PCR system of Panax ginseng by orthogonal design

An orthogonal design was used to optimize SSR-PCR amplification system using Panax ginseng genomic DNA as template. Four levels of five factors （DNA template, Taq DNA polymerase, Mg^2＋, primer, and dNTP） and annealing temperature have been tested separately in this system. The results demonstrated the reaction efficiency was affected by these factors. Based on the results, a stable, productive and reproducible PCR system and cycling program for amplifying a ginseng SSR locus were obtained： 20 μL system containing 1.0 U Taq DNA polymerase, 2.0 mmol·L^-1 Mg^2＋, 0.2 mmol·L^-1 dNTPs, 0.3 μmol·L^-1 SSR primer, 60 ng· μla^-1 DNA template, performed with a program of 94℃ for 5 min, 94℃ for 30 s, annealing at 56.3℃ for 30 s, 72℃ for 1 min, 37 cycles, finishing at 72℃ for 7 min, and storing at 4℃.     

低温冷等离子体对不同含水率杨木单板表面改性的初步研究

笔者采用低温等离子片材表面处理机处理气干、绝干、过干三种含水率条件下的杨木单板,测量其处理前后表面润湿性和胶合性能,结果表明:冷等离子体改性后,气干、绝干、过干三种含水率下的杨木单板表面接触角分别降低13.3%、22.8%、39.3%(甘油),16.2%、35.2%、64.3%(脲醛树脂胶),且降低幅度随含水率降低呈递增趋势;冷等离子体改性能有效提高杨木单板的胶合性能,其变化规律与润湿性基本一致。     

Microwave and steam injection drying of CO2 laser incised Sugi lumber

To investigate the effect of CO₂ laser incising under five drying methods on drying characteristics of Sugi lumber, the squares (120 mm × 120 mm) of Sugi lumber with length of 650 mm were used. A half of samples were incised by CO₂ laser with incising density of 2,500 holes/m². Five types of drying methods were used: microwave drying, steam injection drying, and three combinations of microwave heating and steam injection drying. Steam injection drying was conducted by injecting superheated steam of 120 °C through a perforated plate heated to 140 °C of an injection press. Microwave was irradiated with the power of 3 kW at frequency of 2.45 GHz. The results indicated that incising helps heat through a specimen and thus the whole temperature raised rapidly, which was up to threefolds compared to that of no-incised one. Incised specimens dried by a combination of microwave heating for 1 h and steam injection showed the highest drying rate, which was up to 5.3 %/h. Incising and microwave heating contributed positively to dry lumber under more uniform distribution of moisture content and to reduce surface and internal checks. Incised specimen dried by microwave showed the most uniform distribution of moisture content without surface and internal checks.     

The smell and odorous components of dried shiitake mushroom, Lentinula edodes V: changes in lenthionine and lentinic acid contents during the drying process

This study on dried shiitake mushroom [Lentinula edodes (Berk.) Pegler] focuses on the behavior of the aromatic lenthionine compound and its precursor, lentinic acid, during the drying process. Only a small amount of lenthionine was present after the drying process, regardless of the drying temperature or time; however, the amount increased during the rehydration process using pH 8.0 buffer. The lenthionine content after incubation in the buffer was correlated with the lentinic acid content in the dried shiitake mushroom. The lentinic acid content increased signifi cantly during the drying process at 40°C up to 4 h. The results show that the characteristic smell of dried shiitake mushroom was weak after drying, and that rehydration in a mild alkaline solution was necessary to increase the smell. The lentinic acid content of dried shiitake could serve as an indicator of the smell produced by rehydration and would be useful in screening to select odor-rich strains. Moderate heating likely caused the increase in lentinic acid content, which might be related to a reaction to heat.     

单板干燥过程的热力学研究进展

在胶合板和单板层积材的生产过程中,单板干燥是一个重要的步骤。为了系统理解和改进单板的干燥工艺,文中从单板干燥机在干燥过程中的能量分析以及单板在干燥过程中所发生的传热传质现象2个方面对单板干燥过程中的热力学现象进行了综述,明确这2方面的热力学分析可以优化单板干燥机能量的利用、提高单板的干燥质量,并对单板干燥过程的热力学分析领域今后的研究方向提出了建议。     

Establishing evaluation index system for desertification of Keerqin sandy land with remote sensing data

科尔沁位于我国东北部,地处东北平原向内蒙古高原的过渡地带(42°41'-45°15'N,118°35'-123°30'E),是受荒漠化影响较重的地区。利用外业调查数据,依据地表形态和生态状况的变化,确定了植被盖度、裸沙地占地百分比和土壤质地3 项评价指标,并建立了基于遥感的科尔沁沙质荒漠化评价指标体系,其中裸沙地占地百分比用混合像元分解的方法获得。利用外业调查的数据对该指标体系进行验证,结果表明该指标体系适于研究区域的荒漠化评价。表4参11。     

Surface characteristics of electroless nickel plated electromagnetic shielding wood veneer

Wood is a kind of porous natural material with very poor electro-conductivity, and it has almost no function of electromagnetic shielding. The method of electroless nickel plating was used to produce wooden material with electrical and effective electromagnetic shielding properties. Ni-P alloy layer was obtained on wood surface. The surface feature of plated wood veneer was observed by SEM and the surface composition and microstructure of the layer under different conditions were investigated by EDS and XRD respectively. Meanwhile, the relevant surface resistivity and electromagnetic shielding effectiveness were measured. Correlations of the phosphorous content in the layer to the structure of Ni-P alloy, electro-conductivity and electromagnetic shielding of plated veneers were discussed. SEM photos showed that the surface of electroless nickel plated veneers were covered with Ni-P alloy layer entirely, which made wood veneers more like metal. At the same time, the results showed that with the decreasing of the phosphorous content in the layer, the microstructure of Ni-P alloy layer transformed to be microcrystalline and electro-conductivity and electromagnetic shielding effectiveness were improved. When the phosphorous content was less than 2.37wt pct in the layer, the microstructure of Ni-P alloy layer was microcrystalline structure and its sur- face resistivity and electromagnetic shielding effectiveness were nearly 0.5Ω/□ and 55-60dB respectively.     

Effects of short-term thermomechanical densification on the structure and properties of wood veneers

The effects of short-term thermomechanical (STTM) densification temperature and pressure on the changes in surface roughness, wettability, mass loss (ML), thickness and density of alder, beech, birch, and pine wood veneer with low moisture content (~5%) were investigated. The anatomical structure of veneers was also observed. Veneer sheets were densified using pressure levels of 4, 8 and 12 MPa at three temperatures: 100°C, 150°C and 200°C for 4 min. The results were compared with those of the non-densified veneers. The obtained results show that STTM densification of veneers similarly to long-term densification of solid wood causes irreversible changes in their properties. The STTM-densified veneer surfaces became smoother and more hydrophobic, ML increased slightly while roughness and thickness values decreased significantly, the cell lumens collapsed and a certain amount of fractures in cell walls developed with increasing densification temperature and pressure. All of the investigated wood species showed higher density values after densification. It was found that an even STTM densification of veneers provides stable properties under normal atmosphere conditions; in particular, the thickness and contact angle values were stable for 24 hours after densification, which is an important consideration for industrial applications.     

我国林业高等院校发表英文科技论文的比较研究

统计了北京林业大学、南京林业大学、东北林业大学、浙江林学院、中南林学院和西南林学院6所林业高等院校近20年来被SCIE、EI、ISTP收录和引证的论文,并对其进行了研究和分析。结果表明:①我国林业高校发英文文章的数量偏少、质量偏低,但近年情况有所改善;②6所高校的发展很不均衡,东北林业大学发表数量最多,浙江林学院数量相对较少;③6所高校的发展速度很不均衡,浙江林学院发展最快,其次是北京林业大学和东北林业大学,而南京林业大学几乎没有较大幅度的增长。