Impact of tillage intensity on clay loam soil structure

Soil structure and structural stability are key parameters in sustainable soil management and optimum cropping practices. This study aimed to improve the knowledge of potential precision tillage practices by characterizing the effect of varied tillage intensities on structural properties of a clay loam soil. An experiment with seedbed preparation was conducted using a power take‐off‐driven rotovator equipped to measure torque and angular velocity and with operational speed (OS) and rotational speed (RS) as main factors. Effects of soil coverage prior to tillage and wheeling directly after tillage were measured at one combination of OS and RS. The soil was sampled at 0–80 mm depth. Under slow OS (2.9 km hr^?1) compared with fast OS (6.3 km hr^?1), specific energy input was greater (116 and 52 J kg^?1 on average, respectively), and it increased with RS. Wheeling resulted in larger aggregate diameter right after tillage (at T1; 56 mm as geometric mean compared with 9 mm), with 42 times smaller geometric mean of air permeability 45 days after tillage (at T2) and with greater soil dispersibility at T2. Highly significant correlations were observed between soil dispersibility and energy input, specific surface area of aggregates, fractions of small (<4 mm) and medium (8–16 mm) aggregates, and geometric mean diameter. Slow OS combined with fast RS showed significantly greater air permeability than all other treatments. The results suggest that there is a potential for controlling soil structure in seedbed preparation by minimizing compaction from traffic and adapting site‐specific control of rotovation intensity.     

Effect of tillage treatments on soil thermal conductivity for some Jordanian clay loam and loam soils

Soil thermal conductivity determines how a soil warms or cools with exchange of energy by conduction, convection, and radiation. The ability to monitor soil thermal conductivity is an important tool in managing the soil temperature regime to affect seed germination and crop growth. In this study, the temperature-by-time data was obtained using a single probe device to determine the soil thermal conductivity. The device was used in the field in some Jordanian clay loam and loam soils to estimate their thermal conductivities under three different tillage treatments to a depth of 20 cm. Tillage treatments were: no-tillage, rotary tillage, and chisel tillage. For the same soil type, the results showed that rotary tillage decreased soil thermal conductivity more than chisel tillage, compared to no-tillage plots. For the clay loam, thermal conductivity ranged from 0.33 to 0.72 W m⁻¹ K⁻¹ in chisel plowed treatments, from 0.30 to 0.48 W m⁻¹ K⁻¹ in rotary plowed treatments, and from 0.45 to 0.78 W m⁻¹ K⁻¹ in no-till treatments. For the loam, thermal conductivity ranged from 0.40 to 0.75 W m⁻¹ K⁻¹ in chisel plowed treatments, from 0.34 to 0.57 W m⁻¹ K⁻¹ in rotary plowed treatments, and from 0.50 to 0.79 W m⁻¹ K⁻¹ in no-till treatments. The clay loam generally had lower thermal conductivity than loam in all similar tillage treatments. The thermal conductivity measured in this study for each tillage system, in each soil type, was compared with independent estimates based on standard procedures where soil properties are used to model thermal conductivity. The results of this study showed that thermal conductivity varied with soil texture and tillage treatment used and that differences between the modeled and measured thermal conductivities were very small.     

Verification of traffic-induced soil compaction after long-term ploughing and 10 years minimum tillage on clay loam soil in South-East Norway

Grain yields are presented from a 10-year field trial with four tillage regimes (annual ploughing, harrowing only, ploughing/harrowing alternate years and minimum tillage) on clay loam. We also present soil physical analyses and use the compaction verification tool (CVT) to assess compaction on plots with annual ploughing and minimum tillage, after using slurry tankers with contrasting wheel loads (4.1 Mg, 6.6 Mg) and wheeling intensities (1×/10×) in the 11th trial year, and yields monitored two years after compaction. Winter wheat yields in the period before compaction were strongly affected by tillage, with annual ploughing giving on average 24% higher yield than direct drilling. Both wheat and oats were far less affected in treatments with harrowing only or ploughing/harrowing alternate years, on average within 6% of annual ploughing. Yields after compaction were affected by both previous tillage and compaction intensity. In the first year, single wheeling after annual ploughing gave 23% yield reduction with 4.1 Mg wheel load and 28% reduction with 6.6 Mg wheel load, whilst multiple wheeling gave 14% reduction at 6.6 Mg wheel load. Yield reductions after minimum tillage ranged from 63% (single wheeling with 4.1 Mg) to 100% (multiple wheeling with 6.6 Mg). Similar trends were found in the second year. The soil physical data indicated that all wheeling led to changes in bulk density, pore sizes and permeability in both topsoil and subsoil on both sampled tillage plots. However, effects in the subsoil were partly masked by the soil's high initial bulk density, partly due to its high clay content. The CVT, which plots air capacity against hydraulic conductivity, suggested some harmful compaction on both plots, with the minimum tillage plot being less affected than the ploughed plot. However, yield results did not support this conclusion, indicating that other factors limited yields on the minimum tilled plot.     

Abundance and depth stratification of soil arthropods as influenced by tillage regimes in a sandy loam soil

Different tillage regimes can change soil micro‐environmental characteristics, which may influence the distribution and abundance of soil arthropods. In this study, soil arthropods and soil properties under a winter wheat–summer maize cropping system were investigated in different tillage regimes over four seasons at two depths. The tillage treatments included conventional tillage (CT ), tillage once a year (T1), tillage every two years (T2) and no‐tillage (NT ). The results showed that the primary taxa of soil arthropod were Acarina (65.8%), Collembola (28.5%), Diplura (1.4%) and Coleoptera (1%) over the whole sampling period. The total arthropod density was influenced by tillage treatments and season of sampling. Values for CT plots were significantly greater than those for the NT plots in autumn and spring. In contrast, the Shannon–Wiener diversity index (H’) and the evenness index (J) were relatively higher in CT treatment. The Acarina/Collembola (A/C) ratio was significantly smaller in NT treatment for some sampling seasons as mites were more sensitive to tillage practices. The QBS ‐ar index did not show a clear pattern among treatments in this study. Soil arthropods notably showed seasonal variation in depth stratification. Relative to CT , the total soil arthropods in the NT plots tended to concentrate in the upper layer due to soil compaction in the lower layer. The climate conditions and soil physical properties were the main factors affecting the soil arthropod distribution and composition, as the soil chemical and microbial properties did not differ significantly among all tillage treatments.     

Effect of tillage and crop rotations on pore size distribution and soil hydraulic conductivity in sandy clay loam soil of the Indian Himalayas

Tillage management can affect crop growth by altering the pore size distribution, pore geometry and hydraulic properties of soil. In the present communication, the effect of different tillage management viz., conventional tillage (CT), minimum tillage (MT) and zero-tillage (ZT) and different crop rotations viz. [(soybean–wheat (S–W), soybean–lentil (S–L) and soybean–pea (S–P)] on pore size distribution and soil hydraulic conductivities [saturated hydraulic conductivity (K_sat) and unsaturated hydraulic conductivity {k(h)}] of a sandy clay loam soil was studied after 4 years prior to the experiment. Soil cores were collected after 4 year of the experiment at an interval of 75 mm up to 300 mm soil depth for measuring soil bulk density, soil water retention constant (b), pore size distribution, K_sat and k(h). Nine pressure levels (from 2 to 1500 kPa) were used to calculate pore size distribution and k(h). It was observed that b values at all the studied soil depths were higher under ZT than those observed under CT irrespective of the crop rotations. The values of soil bulk density observed under ZT were higher in 0–75 mm soil depth in all the crop rotations. But, among the crop rotations, soils under S–P and S–L rotations showed relatively lower bulk density values than S–W rotation. Average values of the volume fraction of total porosity with pores <7.5 μm in diameter (effective pores for retaining plant available water) were 0.557, 0.636 and 0.628 m³ m⁻³ under CT, MT and ZT; and 0.592, 0.610 and 0.626 m³ m⁻³ under S–W, S–L and S–P, respectively. In contrast, the average values of the volume fraction of total porosity with pores >150 μm in diameter (pores draining freely with gravity) were 0.124, 0.096 and 0.095 m³ m⁻³ under CT, MT and ZT; and 0.110, 0.104 and 0.101 m³ m⁻³ under S–W, S–L and S–P, respectively. Saturated hydraulic conductivity values in all the studied soil depths were significantly greater under ZT than those under CT (range from 300 to 344 mm day⁻¹). The observed k(h) values at 0–75 mm soil depth under ZT were significantly higher than those computed under CT at all the suction levels, except at −10, −100 and −400 kPa suction. Among the crop rotations, S–P rotation recorded significantly higher k(h) values than those under S–W and S–L rotations up to −40 kPa suction. The interaction effects of tillage and crop rotations affecting the k(h) values were found significant at all the soil water suctions. Both S–L and S–P rotations resulted in better soil water retention and transmission properties under ZT.     

Performance evaluation of tillage tines operating under different depths in a sandy clay loam soil

The study investigated the performance of three model tillage tools (tines). The experimental tillages were made from flat 8 mm plain carbon steel. They were designated T1, T5, and T20, corresponding to tine widths of 1, 5, and 20 cm respectively. Experiments were carried out in a soil bin filled with sandy clay loam soil at average moisture content 11.5% (dry basis) and 600 kPa average cone index. The plastic limit and liquid limit and plasticity index of the soil are 20%, 31% and 11% respectively. Tests were conducted at forward speeds of 0.28, 1.0, and 2.5 m/s. Depths of operation considered were 35, 70, 150, 200 and 250 mm. Draught measurements were made for the different tines and were also calculated using soil mechanics equation. There was reasonable agreement between measured and predicted draught forces. The effects of depth of operation on draught force of the tines were studied and evaluated. It was observed that draught increased at an increasing rate with depth; the relationship was a curvilinear one best fitted by exponential function. The soil disturbance created as a result was also evaluated and reported in this paper. The parameters used to define soil disturbance of a single tine were: ridge-to-ridge distance (RRD), maximum width of soil cut (WFS), maximum width of soil throw (TDW), after furrow depth (df), height of ridge (hr) and rupture distance (f). They all increased as the depth of operation of the tool increased but less proportionately. The critical depth of the tines was also estimated.The results of analysis of variance showed that tool type and operating depth significantly affected draught at 5% level of significance (p < 0.05) and that, there was interaction between the two factors.     

不同耕作方式对中国东北黑土有机碳的短期影响

A tillage experiment, consisting of moldboard plow （MP）, ridge tillage （RT）, and no-tillage （NT）, was performed in a randomized complete block design with four replicates to study the effect of 3-year tillage management on SOC content and its distribution in surface layer （30 cm） of a clay loam soil in northeast China. NT did not lead to significant increase of SOC in topsoil （0-5 cm） compared with MP and RT; however, the SOC content in NT soil was remarkably reduced at a depth of 5-20 cm. Accordingly, short-term （3-year） NT management tended to stratify SOC concentration, but not necessarily increase its storage in the plow layer for the soil.     

Effects of alternative tillage systems on soil quality and yield of spring cereals on silty clay loam and sandy loam soils in the cool, wet climate of central Norway

Tillage trials were established on a poorly drained silty loam overlying silty clay loam and on a freely drained sandy loam overlying medium sand, in 1988 and 1989, respectively. Autumn and spring ploughing and two ploughless systems were compared for 12–13 years, with three replications at each site. The ploughless treatments comprised deep versus shallow spring harrowing until 1999, and thereafter autumn plus spring harrowing versus spring harrowing only. In 6 years, treatments with and without fungal spraying of the cereal crops were included. In other years, fungicides were not used. Perennial weeds were controlled by herbicides as necessary, on nine occasions up until 2001. Average spring barley (Hordeum vulgare L.) and spring oat (Avena sativa L.) yields were similar with spring ploughing as with autumn ploughing at both sites. In treatments without ploughing, average yields on the silty loam over clay were 93% of those obtained with ploughing, and on the sandy loam over sand they were 81%. Smaller and non-significant yield differences were found between spring harrowing versus deep spring harrowing, and between autumn plus spring harrowing versus spring harrowing only. Fungal spraying increased yields markedly at both sites (25%), but there was no significant interaction between this treatment and tillage system. Oat was compared with barley in 2 years, with oat performing better under ploughless tillage. At both sites increases in penetrometer resistance occurred in the topsoil of unploughed treatments. These were considered particularly limiting on the sandy loam. On the silty loam there was an increase in surface horizon porosity in the absence of ploughing, which was associated with an increase in topsoil organic matter content. On this soil there was also a tendency toward lower penetrometer resistance at >30 cm depth on autumn plus spring harrowed soil than on ploughed soil, indicating that the plough pan may have diminished. This was supported by observations of greater earthworm activity on unploughed soil. Soil chemical analyses revealed that mineral N and plant-available P and K accumulated in the upper horizon under ploughless tillage. The percentage yields obtained in individual years with autumn as opposed to spring ploughing, were positively correlated with air temperature during 0–4 weeks after planting on the silty loam, and with precipitation during 0–12 weeks after planting on the sandy loam. In the case of yields obtained with spring harrowing only, relative to spring ploughing, positive correlations were found with 0–4 week temperature on both soil types, suggesting that low early season temperatures may limit yields under ploughless tillage.     

Field assessment of crusting on a tilled sandy clay loam

Nine different techniques were used to record the initial change in the physical and hydrological properties of a freshly tilled soil surface following successive cycles of wetting and drying. The study was made in the field on a sandy clay loam soil ploughed and harrowed and then exposed to three simulated rainfall events of 76 mm/h for 15 minutes. Although the degradation of the soil surface increased with each successive rainfall, the most significant changes were observed after the first rainfall. Qualitative observations of clod size distribution and crust development provide a good indication of the early stages of soil surface degradation. Complementary physical data were quickly obtained using a hand held shear vane. These techniques are simple and robust enough that they can be used in on-farm research programmes, where resources, both human and technical are at a premium. Tension infiltrometry provided hydrological information that complemented the physical information provided by the above techniques, but is not as simple.     

Energy optimization for subsoilers in tandem in a sandy clay loam soil

In some maize growing regions of South Africa, conventional subsoilers are used in a tandem configuration to till up to 600 mm. The farmers believe the tandem configuration decreases the draft force per unit area tilled. If so, this probably happens because the critical depth for the rear subsoiler is increased beyond its maximum working depth of 600 mm. Such tillage systems necessitated this study with an ultimate goal of establishing the relative position of the front subsoiler at which energy utilization can be optimized.

Experiments were conducted under field conditions in a fine sandy clay loam soil and consisted of a continuous measurement of horizontal and vertical forces acting on each subsoiler at a constant speed of 1.5 kmph. The rear subsoiler was operated at a constant depth of 600 mm while that of the front subsoiler and the spacing were varied. Further more, at the end of each run the cross-sectional areas of the disturbed soil-profiles were measured at different sections and the total failure profiles constructed by a Matlab-based computer program.

The results showed that the cross-sectional area failed per unit draft force linearly increased with spacing between the subsoilers. The efficiency of the subsoilers in this configuration was maximized when the longitudinal spacing was such that the soil failed by the front subsoiler was allowed to stabilize before the rear subsoiler reached it. The maximum cross-sectional area failed per unit draft force was recorded when the depth of the front subsoiler was equal to about 80% of the operating depth of the rear subsoiler.

The knowledge contributed by this research will not only facilitate qualitative field operations and optimize energy use, but also promote better management decisions.     

Seasonal differences in tillage draught on a sandy loam soil with long‐term additions of animal manure and mineral fertilizers

Energy requirements for soil tillage are closely linked to soil properties, such as clay, water and soil organic carbon (SOC) contents. Long‐term application of inorganic fertilizer and organic amendments affects SOC content but little is known about seasonal differences in tillage draught requirements of soils subject to contrasting nutrient management regimes. We assessed autumn and spring tillage draught following harvest of early‐sown and timely sown winter wheat grown on a sandy loam in the Askov Long‐Term Experiment on Animal Manure and Mineral Fertilizers. Draught force was related to soil texture, soil water and SOC content, shear strength and bulk density, nutrient management, and yield of the preceding winter wheat. Contents of clay and SOC ranged from 8.9 to 10.6% and from 0.98 to 1.36%, respectively. In the autumn and spring, SOC normalized by clay content explained 38 and 5% of the variation in specific draught, respectively. Specific draught did not differ significantly among individual fertilization treatments. SOC was closely correlated with clay and water contents and bulk density, and with yield of the preceding wheat. Draught force was significantly smaller in the spring than in the autumn. In the autumn when soils were drier (?700 hPa), tillage draught was correlated with several soil characteristics, whereas water content was the dominating parameter in the spring when soils were wetter (?100 hPa). The range of SOC contents observed in this study aligns with that observed in Danish sandy loams under intensive cultivation, and within this range, SOC per se had little effect on draught requirements.     

Wear of spring tine cultivator points in sandy loam and light clay soils in southern Poland

Correct evaluation and forecasting of durability of soil cutting parts are the decisive factors for proper operation of agricultural machinery. During operation of cultivators, over two-fold difference in wear of cultivator points is observed, which makes establishing of their exchange periods extremely difficult. So, there is a need to conduct some research aimed for determination of relationship between arrangement of the points in individual cultivator rows and their wear. The presented experiments were performed under authentic farm conditions during spring soil loosening and levelling operations before sowing and planting, in sandy loam and light clay soils. Changes in length and thickness of the spring tine points, wear patterns and weight loss were measured. Loss in length of spring tine points was described by a complex function of the distance travelled or by an exponential function of the distance from the measuring point to the symmetry axis of a spring tine point; loss in thickness was described by a linear function. It was found that soil type, as well as arrangement of the points in individual cultivator rows and their position in relation to the tractor wheel track, significantly influenced their wear. It was also observed that wear of spring tine points was 40–100% higher in the sandy loam soil than in the light clay soil, and that wear within a tractor wheel track was 17–40% higher than outside the track. Moreover, wear of points positioned in the first row on the cultivator frame was 26–100% higher than wear of those in the third row. The research results emphasise the need for field experiments at compare wear of spring tine points made of different materials or of different designs to take into account differences in wear due to positioning of the points on cultivator frames.     

Recent yield results and trends over time with conservation tillage on morainic loam soil in southeast Norway

Abstract

Results for 1998–2004 are reported from four long-term (25–28 years) tillage trials, comparing conventional autumn ploughing with reduced tillage, normally spring harrowing only. Plant residues were retained during the period studied. The weather was somewhat wetter than the 1961–1990 normal. Results with reduced tillage were mostly similar to those seen in earlier trial periods. In Trial 1, mean grain yield was 95% with spring harrowing only versus autumn ploughing, 96% when harrowing in autumn was performed as well and 97% when the soil was ploughed every third year. In Trial 2 positive crop rotation effects were found both with and without ploughing, and reduced tillage gave 5% lower grain yield also in this trial. In Trial 3, tillage system did not affect yields of cereals grown in rotation with potatoes, but reduced tillage gave 12% lower potato yield than ploughing. Little difference in response to N fertilizer was found. In Trial 4, reduced tillage on large-scale (0.7 ha) plots gave 11% lower grain yields than annual ploughing, partly due to shallow sowing depth. No long-term trend in yield responses to tillage was discernible in any trial, and between-year variability was similar with both ploughing and reduced tillage. Percentage yields with reduced tillage relative to annual ploughing correlated positively with rainfall in May and with mean air temperature in August. It is concluded that the reduced tillage systems studied are sustainable in terms of productivity, relative to labour, machinery and energy inputs. Likely benefits of such systems include higher levels of organic matter and aggregate stability in surface soil horizons, but a disadvantage is the need for frequent herbicide use to control perennial weeds.     

Soil macropore dynamics affected by tillage and irrigation for a silty loam alluvial soil in southern Portugal

Soil tillage can have a significant effect on soil porosity and water infiltration. This study reports field measurements of near saturated hydraulic conductivity in an undisturbed soil under two tillage treatments, conventional tillage (CT) and minimum tillage (MT). The objective was to determine effective macro and mesoporosities, porosity dynamics during the irrigation season, and their contribution to water flow. Field observations were performed during the 1998 maize (Zea mays L.) cropping season in an Eutric Fluvisol with a silty loam texture, located in the Sorraia River Watershed in the south of Portugal. Infiltration measurements were done with a tension infiltrometer. At each location an infiltration sequence was performed corresponding to water tensions (φ) of 0, 3, 6 and 15 cm. Five sets of infiltration measurements were taken in both treatments in the top soil layer between May and September. One set of measurements was done at the depth of 30 cm at the bottom of the plowed layer in the CT plot. After 5 years of continuous tillage treatments the results show that regardless of the tillage treatment, saturated conductivity values K(φ₀) were several times larger than near saturation conductivity K(φ₃). This indicates that subsurface networks of water conducting soil pores can exist in both CT and MT maize production systems. In CT, the moldboard plow created macro and mesoporosity in the top soil layer while breaking pore continuity at 30 cm depth. This porosity was partially disrupted by the first irrigation, resulting in a significant decrease of 45% in the macropore contribution to flow. Later in the season, the irrigation effect was overlaid by the root development effect creating new channels or continuity between existing pores. In MT macroporosity contribution to flow did not show significant differences in time, representing 85% of the total flow. In both the treatments, macropores were the main contributing pores to the total flow, in spite of the very low macroporosity volumes.     

Soil mineral-N and N-fertilizer requirements of spring cereals in two long-term tillage trials on loam soil in southeast Norway

Much uncertainty exists among growers concerning the need to adjust N-fertilizer application to cereals when reduced tillage is adopted. Studies in long-term trials are required to give an adequate answer to this question, which is of both economic and environmental interest. N-fertilizer requirements of spring cereals and of soil mineral nitrogen contents at different times of the year were measured over the period 1991–1996 in two long-term tillage trials established in 1980 at Kise (60°46′N, 10°49′E) on morainic loam soil. Tillage treatments comprised conventional tillage with autumn ploughing and reduced tillage without ploughing and with harrowing in spring kept to the minimum necessary for seeding. Four levels of N-fertilizer (0, 60, 90 and 120 kg N/ha) were compared in 1991–1995 in barley (Hordeum vulgare L.) and wheat (Triticum aestivum L.), and their residual effect was measured in 1996. Levels of soil mineral nitrogen before fertilization in spring were on an average 8% lower with reduced tillage than with conventional tillage. Plant development was delayed with reduced tillage, but this was compensated for later in the season. A two-year incubation study under covered plots in the field did not reveal any effect of tillage on net nitrogen mineralisation. There was a tendency to higher straw yield with reduced tillage, but no overall effect on grain yield. Responses to N-fertilizer were almost identical with both the tillage systems, and yields increased up to the highest level of application. Crop nitrogen contents were monitored, but only minor differences were found between tillage systems in total uptakes and apparent N-fertilizer recoveries. On the basis of these results it is concluded that long-term reduced tillage does not affect the N-fertilizer requirements of spring cereals on loam soils under cool climatic conditions.     

Rainfall and tillage effects on soil structure after alfalfa conversion to maize on a clay loam soil in New York

Soil degradation is accelerated when perennial crops are converted to annual row crops, primarily due to increased soil disturbance from tillage. Subsequent heavy rainfall may induce soil settling, reduce macroporosity and increase hardsetting upon drying. An experiment involving plow and no-tillage and two simulated rainfall treatments (‘wet’ and ‘dry’) was conducted on Kingsbury clay loam soil in northern New York in 1992 and 1993 to study their effects on soil structure under maize (Zea mays L.) after conversion from alfalfa (Medicago sativa L.), and to evaluate the use of spectral analysis of micropenetrometer observations for studying soil aggregation. Undisturbed soil cores were collected from the row and trafficked and non-trafficked interrow positions at the 0.05 and 0.15 m depths and used for laboratory measurement of soil strength and pore system properties. These well-structured soils show a high contribution (up to 0.15 m³ m⁻³) of macropores to the total porosity of the soil. Soil strength was generally slightly higher for no-till (NT) than plow till (PT), although only significant in 1992. Soil strength in the surface layer did not change significantly with drying. Spectral density patterns did not show strong treatment effects, although distinct peaks reflect 3.0–3.5 mm stable structural units within macroaggregates. Simulated rainfall treatments and tillage treatments generally did not strongly affect measured soil properties, presumably due to stable soil structure. Structurally stable clay loam soils show little effect of tillage or settling on soil physical properties in the first years after alfalfa to maize conversion, and have good potential for long-term annual crop production if properly managed.     

Effect of design parameters of flat tillage tools on loosening of a clay soil

Very little research has been done to investigate soil loosening as a function of the geometry of the tillage tool and of the original soil properties and moisture content. A field experiment was conducted to observe the effects of the geometric parameters of flat tillage tools on their draft, cutting efficiency and loosening of a moist clay soil. The test tool variables included rake angles to the horizontal of 30, 60 and 90°, widths of 75 and 150 mm and depths of operation of 100, 150 and 200 mm. Measurements were taken of draft, disturbed soil cross sectional profiles and the initial area of soil disturbed by the tools. The resulting draft requirement increased with width, depth and rake angle of the tool. The cross sectional area of soil disturbed did not change appreciably with rake angle, but the significant increase in draft with angle resulted in markedly diminished soil cutting efficiency (area divided by draft). The degree of soil loosening was generally smaller at a rake angle of 60° than at 30 or 90°, and tended to be higher at greater depths of operation. In addition, a larger depth to width ratio generally increased the degree of loosening. Results for the soil studied indicate that the best implement design for low draft, high cutting efficiency and superior soil loosening should have a rake angle of about 30° and should be fairly narrow with a depth to width ratio of 2 or more.     

Grain yields and soil properties on loam soil after three decades with conservation tillage in southeast Norway

Four tillage trials have been performed on moderately well-drained loam soil in southeast Norway for 30–37 years (mean 34), comparing reduced tillage (8–10 cm in spring) with autumn ploughing (25 cm). In some years, additional stubble harrowing in autumn (10–12 cm) was compared with harrowing only in spring. Weeds were controlled with herbicides. Straw residues were retained after around 1990 and no fungicides were used. Grain yields are reported for the last nine years, and compared with earlier years. Results are presented for a number of soil properties measured in recent years. Autumn harrowing gave no consistent yield benefit over harrowing only in spring. There was little difference between ploughed and unploughed treatments in mean grain yields over the whole trial period, and the variability between years was similar in both tillage systems. Relative grain yields, calculated as yields obtained without ploughing in percentage of those obtained with ploughing, appeared to be normally distributed around 100%. Responses were often positive in dry years, and negative in wet years. Reduced tillage gave higher P and K concentrations near the soil surface and slightly lower concentrations in deeper layers. There was little change in their levels, relative to earlier findings. Changes in bulk density and total porosity were mostly attributable to changes in the stratification of organic matter. Reduced tillage increased porosity at 4–8 cm depth and decreased it slightly at 24–28 cm, but there was no change in the intermediate layer. The moisture-holding capacity of the soil was altered little by reduced tillage, and soil aeration properties were satisfactory at all three depths measured. There was no change in the total amount of organic matter stored within the topsoil, despite marked changes in its distribution. Reduced tillage gave significant increases in aggregate stability and an indication of greater earthworm activity.     

Earthworm populations as affected by crop practices on clay loam soil in a Mediterranean climate

Abstract

Earthworms influence soil fertility, and their population is known to be influenced by fertilization. The objective of this study is to characterize the abundance of earthworms under three different kinds of rotation-crops (Rotation: cereals–legumes for green manure-cotton), three tillage systems (Conventional Tillage CT, Minimum Tillage MT, & No-Tillage NT) and fertilization (NP: inorganic and FYM: farmyard manure-organic). Significantly higher populations of earthworms were found under the legumes and NT system in contrast to the lowest abundance determined under the cotton and CT system. Earthworm populations benefited more from organic fertilization than from NP. Our study showed that the most important factors for earthworm abundance are the macropores and C_org under Mediterranean conditions. No-till management considerably influenced the improvement of the physical and chemical soil properties and increased the earthworm abundance.     

耕作机具能耗模拟研究进展(英文)

耕作机具的能耗模拟研究始于20世纪60年代。近年来,性能强大的计算机应用和先进建模技术与软件的发展,提高了研究人员建模分析和预测不同耕作条件下(如耕作机具所引起的土壤运动、土体破坏分布、作物残茬处理和肥料施用等)机具性能和能耗状况的能力。研究人员使用解析分析、数值模拟和经验法等方法,建立了耕作机具能耗的多种数学模型。该文对耕作机具能耗数学模型进行了系统的概述,总结了已有的研究成果,重点论述了数学模型的分类和特点,模型参数的测定、验证和模型的适用范围,可为耕作机理深入研究和耕作机具优化改进提供参考。