Acetosolv delignification of depithed cardoon (Cynara cardunculus) stalks

Modelling of the Acetosolv treatment of the cardoon bark (Cynara cardunculus) was accomplished using a second-order face-centred factorial design. We considered as independent (experimental) variables: cooking time (60–180 min), acetic acid concentration in the cooking liquor (60–90%) and hydrochloric acid concentration in the cooking liquor (0.20–0.80%); as well as dependent variables: pulp yield, kappa number and viscosity.Empirical models were deduced to satisfactorily fit experimental data with the values of the independent variables and allow quantifying the effects of each variable.An optimisation with constraints led to the calculation of the region of the experimental domain (time = 180 min, acetic acid concentration ≥ 71.3% and HCl concentration > 0.41%) leading to pulps with kappa numbers < 25 at a maximal pulp yield and viscosity, giving us maximum possible values for pulp yield (46.3%) and viscosity (557 mL/g).     

Protein extraction from defatted wheat germ by reverse micelles: Optimization of the forward extraction

In this work, the forward extraction of defatted wheat germ protein (DWGP) by reverse micelles was studied. The reverse micellar systems were formed by sulphosuccinic acid bis (2-ethylhexyl) ester sodium salt (AOT), isooctane and KCl solution. The effects of AOT concentration, pH, KCl concentration, extraction time, the amounts of defatted wheat germ flour (DWGF), W₀ (the molar ratio of water to surfactant, i.e. W₀ = [H₂O]/[AOT]) and temperature on the forward extraction efficiency of DWGP were tested. On the basis of single-factor experiments, the optimum extraction was achieved by response surface methodology (RSM). The experimental results lead to the conclusion that the highest forward extraction efficiency of DWGP was reached at the AOT concentration 0.06 g/mL, pH 8, KCl concentration 0.1 mol/L, time 30 min, the amounts of DWGF 0.500 g, W₀ 25 and temperature 36 °C. Under these conditions, the forward extraction efficiency of DWGP achieved 37%.     

Foliar sprays of concentrated urea at maturity of pigeonpea to induce defoliation and increase its residual benefit to wheat

The pigeonpea (Cajanus cajan (L.) Millsp.) crop retains appreciable amounts of green foliage even after reaching physiological maturity, which if allowed to defoliate, could augment the residual benefit of pigeonpea to the following wheat (Triticum aestivum L.) in a pigeonpea–wheat rotation. The effect of addition of leaves present on mature pigeonpea crop to the soil was examined on the following wheat during the 1999/2000 growing season at Patancheru (17°4′N, 78°2′E) and during the 2001–2003 growing seasons at Modipuram (29°4′N, 77°8′E). At Patancheru, an extra-short-duration pigeonpea cultivar ICPL 88039 was defoliated manually and using foliar sprays of 10% urea (30 kg/ha) and compared with a millet (Pennisetum glaucum (L.) R.Br.) crop, naturally senesced leaf residue and no-leaf residue controls. At Modipuram, the effect of 10% urea spray treatment on mature ICPL 88039 was compared with the unsprayed control. At both locations, the rainy season crops were followed by a wheat cultivar UP 2338 at four nitrogen levels applied in a split plot design, which at Patancheru were 0, 30, 90 and 120 kg N ha⁻¹ and at Modipuram 0, 60, 120 and 180 kg N ha⁻¹. At Patancheru, urea spray added 0.5 t ha⁻¹ of extra leaf litter to the soil within a week without significantly affecting pigeonpea yield. This treatment, however, increased mean wheat yield by 29% from 2.4 t ha⁻¹ in the no-leaf residue pigeonpea or pearl millet plots to 3.1 t ha⁻¹. At Modipuram, the foliar sprays of urea added more leaf litter to the soil than at Patancheru. Here, increase in subsequent wheat yield due to additional pigeonpea leaf litter was 7–8% and net profit 21% more than in the unsprayed control. The addition of pigeonpea leaf litter to the soil resulted in a saving of 40–60 kg N for the following wheat crops in both the environments. The results demonstrated that pigeonpea leaf litter could play an important role in the fertilizer N economy in wheat. The urea spray at maturity of the standing pigeonpea crop significantly improved this contribution in increasing wheat yield, the effect of which was additional to the amount of urea used for inducing defoliation. The practice, if adopted by farmers, may enhance sustainability of wheat production system in an environmentally friendly way, as it could reduce the amount of fertilizer N application to soil and enhance wheat yield.     

Responses of sunflower yield and grain quality to alternating day/night high temperature regimes during grain filling: Effects of timing,duration and intensity of exposure to stress

In order to quantify the effects, at different stages during grain filling, of alternating day/night high temperature regimes on sunflower grain yield and quality, heads were exposed to high temperatures during 7 or 6 days starting either 10–12 days after anthesis (daa, HT1), 18 daa (HT2) or 24 daa (HT3). Also, heads were exposed to high temperatures for periods of 2, 4 or 6 days in each of HT1 and HT2. Temperatures covered a range of mean daily grain temperature of 20–40 °C and peak grain temperatures (i.e., those prevailing during the central 5 h of the daylight period) of 26–45 °C. High temperature stress for periods of 4 days or longer produced significant (p < 0.05) reductions in grain yield and grain quality. Early (HT1) exposure to stress reduced yield by 6%/°C above a mean grain temperature threshold of 29 °C; later (HT2 + HT3) exposures reduced yield by 4%/°C above a threshold of 33 °C. These reductions in yield were attributable to reductions in unit grain weight at all positions (periphery, intermediate, central) on the head, and an increase in the proportion of very small (10–30 mg) grains, termed half-full (HF) grains in this paper. In both full and HF grains, stress in either HT1 or HT2 reduced final pericarp weight, associated with fewer number of cell layers and thinner cell walls in the schlerenchyma. High temperatures reduced both the rate and duration of oil deposition in the grain, with the greatest effects being found with early (HT1) exposures. The unsaturation (oleic acid/linoleic acid) ratio of oil from mature grain was altered only when exposure to heat stress overlapped with the cessation of deposition of storage lipids. The effects of duration and intensity of heat stress on relative (to control) grain yield and oil content could be reasonably summarized using a linear response to cumulative hourly heat load calculated with a base temperature of 30 °C. We conclude that: (i) 4 days of alternating day/night temperatures resulting in mean daily grain temperatures of >30 °C can reduce sunflower grain yield and quality; (ii) the magnitude of these effects is strongly dependent on the timing of exposure and their nature on the grain growth processes active at the time of stress; and (iii) an hourly heat load (base = 30 °C) provides a useful integrative estimator of the effects of exposure to heat stress on grain yield and oil content for a given phase of grain filling.     

Bio-oil production from soybean (Glycine max L.); fuel properties of Bio-oil

Soybean oil cake (SOC) has been studied to produce bio-oil in a fixed-bed pyrolysis unit. The effect of pyrolysis parameters on the product yields and compositions were investigated. The highest bio-oil yield of a ca 25.8 wt.% was obtained at 400 °C pyrolysis temperature with a heating rate of 50 °C/min for particles of 0.425–0.600 mm in size. The various characteristics of bio-oil acquired under these conditions were identified. The empirical formula of bio-oil with a calorific value of 33.6 MJ/kg was established as CH_1.37O_0.15N_0.14. The chemical characterization studies showed that the bio-oil obtained from SOC might be a potentially valuable source as renewable fuel and chemical feedstocks.     

Combining ability analysis to identify suitable parents for heterosis in seed cotton yield,its components and lint % in upland cotton

Combining ability and heterosis were studied in a 6 × 6 diallel cross to see the nature of gene action in Upland cotton (Gossypium hirsutum L.) during 2002 to 2004. Analysis of variance revealed highly significant differences among all the F₁ and F₂ hybrid means and their respective six parental values for all the traits examined. In both generations, the mean squares due to general combining ability (GCA) and specific combining ability (SCA) were also highly significant. SCA genetic variances were greater than GCA and more important for the traits, i.e. boll weight, boll number and seed cotton yield per plant, showing the predominance of non-additive gene action. Lint % in both generations and boll weight in F₂s only were controlled by additive type of gene action due to maximum GCA variances. Cultivar CIM-1100 was found to be the best general combiner and its utilization produced valuable hybrids with desirable SCA in both generations. F₁ and F₂ hybrids, viz., CIM-1100 × CRIS-9, CIM-1100 × FH-682, CIM-1100 × BH-36 and CIM-109 × CIM-1100 as high × low and low × high parents performed well in SCA determination, outstanding mean performance and heterosis. Better SCA effects associated with useful heterosis were more pronounced for yield traits. In F₁ hybrids, maximum heterosis was observed for seed cotton yield followed by boll number, boll weight and lint %. The heterosis over better parent was +3.13 to +65.63% for bolls per plant, +0.75 to +24.40% for boll weight, +0.82 to +115.22% for seed cotton yield and +0.27 to +3.88% for lint %. Involvement of CIM-1100 in most of the F₁ and F₂ hybrids resulted in the synthesis of superior genotypes for most of the traits studied. Inbreeding depression was elevated in good performing hybrids and was the highest for seed cotton yield. Highest yielding F₁ hybrids yielded lesser in the subsequent generation due to over-dominance and inbreeding depression, whereas moderate yielding F₁ hybrids were found more stable even passing through process of segregation due to additive gene action. The combined performance of F₁ and F₂ hybrids could be a good indicator to identify the most promising populations to be utilized either as F₂ hybrids or as a resource population for further selection.     

Seed germination response of cuphea to temperature

Cuphea (Cuphea viscosissima Jacq. × C. lanceolata W.T. Aiton; PSR23) is a potential new oilseed crop. Its oil is high in medium-chain fatty acids that are suitable for detergent/cleaner applications and also for cosmetics. The objective of this study was to determine the critical temperatures for cuphea seed germination. To determine the base, maximum, and optimum temperatures for seed germination, mature cuphea seeds were harvested from plants grown at Prosper, ND, in 2004, 2005, and 2006. Seeds were germinated on a temperature-gradient bar varying between 5 and 35 °C. Cumulative germination was calculated for each temperature treatment. Base temperature (T_b) and optimum temperature (T_o) were estimated from the third-order polynomial temperature-response functions for each year. In addition, germination rate per day was used in a linear model to estimate the base temperature below which germination rate was equal to zero (T_b), and the maximum temperature above which germination was equal to zero (T_m). The optimum temperature (T_o) was calculated as the intercept of sub-optimal and supra-optimal temperature-response functions. Through the third-order polynomial temperature-response functions and the sub-optimal/super-optimal intercept approaches, we were able to generate six estimates for each critical value. Estimates of the base temperature for cuphea seed germination ranged between 3.3 and 11 °C, with the most reliable estimates between 6 and 10 °C, similar to many warm-season crops such as corn (Zea mays L.) and sorghum (Sorghum bicolor L.). The optimum temperature for cuphea seed germination ranged between 18.5 and 24 °C with a mean value of 21 °C. The maximum temperature for seed germination ranged 33–38 °C. On this basis, a cuphea planting date after 20 May is recommended for east-central North Dakota.     

Polyphenolic extract and essential oil quality of Thymus zygis ssp. gracilis shrubs cultivated under different watering levels

Thymus zygis ssp. gracilis shrubs were cultivated as an experimental crop under different watering level, in order to achieve 81, 63, 44 and 30% of the local potential evapotranspiration (ETo). After 4 years of cultivation, thyme leaves were analyzed on the basis of their essential oil (yield and quality), total phenolic content, free radical-scavenging activity and polyphenolic profile.Essential oil yield values ranged between (2.3 ± 0.7) and (3.6 ± 0.7)% for 81 and 30% ETo equivalent, respectively. The comparison of essential oil production at the 2nd and 4th years of cultivation showed that using watering levels higher than 30% ETo equivalents reduced significantly (P < 0.05) the essential oil yielded by these shrubs with time.Analysis of total phenolic content, polyphenolic profile, and radical scavenging activity were performed using post-distillation dry leaves. Total phenolic content values ranged from (122.2 ± 19.3) to (108.5 ± 19.2) mg of gallic acid equivalents (GAEs)/g of dry plant for the highest and lowest watering level treatment, respectively. Regarding the polyphenolic profile, rosmarinic acid, followed by apigenin, ferulic, carnosic and caffeic acids, was the phenolic component quantified at the highest concentrations. Radical-scavenging activities (IC₅₀) concentrations varied from (3.7 ± 1.6) mg/mL for 81% ETo to (7.4 ± 2.3) mg/mL 30% ETo.In spite of the intra-specific variability detected, the individual analysis of shrubs has allowed the selection of plants which are characterised by having adequate levels of essential oil and polyphenolic extract (yield and quality), almost all of them being cultivated under a 60% ETo watering level. These selected shrubs will allow us to make further vegetative propagations in order to obtain homogeneous field crops with plants of contrasted quality cultivated under a 60% ETo watering level.     

Synthesis and characterization of hazelnut oil-based biodiesel

The demand for diesel fuel far exceeds the current and future biodiesel production capabilities of the vegetable oil and animal fat industries. New oilseed crops that do not compete with traditional food crop are needed to meet existing energy demands. Hybrid hazelnut oil is just such an attractive raw material for production of biodiesel. Hazelnut oil was extracted from hybrid hazelnuts and the crude oil was refined. Hazelnut oil-based biodiesel was prepared via the transesterification of the refined hazelnut oil with excess methanol using an alkaline catalyst. The effects of reaction temperature, time and catalyst concentration on the yield of diesel were examined, and selected physical and chemical properties of the biodiesel were evaluated. The biodiesel yield increased with increasing temperature from 25 to 65 °C and with increasing catalyst concentration from 0.1 to 0.7 wt%. The increase in yield with reaction time was nonlinear and characterized by an initial faster rate, followed by a slow rate. Hazelnut oil-based biodiesel had an average viscosity of 8.82 cP at 25 °C, which was slightly higher than that of the commercial soy-based diesel (7.92 cP at 25 °C). An approximate 12 °C higher onset oxidative temperature and a 10 °C lower cloud point of hazelnut oil biodiesel than those of its commercial soy counterpart indicated a better oxidative stability and flowability at low temperature. The average heat of combustion of hazelnut oil biodiesel was 40.23 kJ/g, and accounted for approximately 88% of energy content of diesel fuel. The fatty acid composition of hazelnut oil-based biodiesel was the same as the nature oil.     

Long-term effects of inorganic and organic fertilizer sources on yield and nutrient accumulation of lowland rice

Deceleration in rice (Oryza sativa L.) yield over time under fixed management conditions is a concern for countries like Bangladesh, where rice is the primary source of calories for the human population. Field experiments were conducted from 1990 to 1999 on a Chhiata clay loam soil (Hyperthermic Vertic Endoaquept) in Bangladesh, to determine the effect of different doses of chemical fertilizers alone or in combination with cow dung (CD) and rice husk ash (ash) on yield of lowland rice. Two rice crops—dry season rice (December–May) and wet season rice (July–November) were grown in each year. Six treatments—absolute control (T₁), one-third of recommended fertilizer doses (T₂), two-thirds of recommended fertilizer doses (T₃), full doses of recommended fertilizers (T₄), T₂+5 t CD and 2.5 t ash ha⁻¹ (T₅) and T₃+5 t CD and 2.5 t ash ha⁻¹ (T₆) were compared. The CD and ash were applied on dry season rice only. The 10-year mean grain yield of rice with T₁ was 5.33 t ha⁻¹ per year, while the yield with T₂ was 6.86 t ha⁻¹ per year. Increased fertilizer doses with T₃ increased the grain yield to 8.07 t ha⁻¹ per year, while the application of recommended chemical fertilizer doses (T₄) gave 8.87 t ha⁻¹ per year. The application of CD and ash (T₅ and T₆) increased rice yield by about 1 t ha⁻¹ per year over that obtained with chemical fertilizer alone (T₂ and T₃, respectively). Over 10 years, the grain yield trend with the control plots was negative, but not significantly, both in the dry and wet seasons. Under T₃ through T₆, the yield trend was significantly positive in the dry season, but no significant trend was observed in the wet season. The treatments, which showed positive yield trend, also showed positive total P uptake trend. Positive yield trends were attributed to the increasing P supplying power of the soil.     

Submergence tolerance and yield performance of lowland rice as affected by agronomic management practices in eastern India

Rice is subjected to excessive waterlogging and flash-flooding on large areas in south and south-east Asia. Besides cultivars, submergence tolerance of plants is influenced by various agronomic practices. A field experiment was conducted at Cuttack, India during 1994–1995 to study the effect of method of stand establishment (direct seeding and transplanting), vigour of seed (low and high-density) or seedlings (N-fertilized and unfertilized), plant population (normal and 50% more) and N fertilizer (single basal and split application) on yield performance of lowland rice under conditions of natural submergence and simulated flash-flooding (impounding up to 90 ± 3 cm depth for 10 days at vegetative stage). Flooding reached a maximum depth of 80 cm in 1994 and 52 cm in 1995 under natural submergence. The crop performance was better in 1994 due to timely sowing in dry soil and delayed accumulation of water (43 days after sowing) than in 1995 when sowing was done late in saturated soil followed by early water accumulation (28 days after sowing). Grain yield of rice decreased by 30.0–33.6% due to simulated flash-flooding compared with natural submergence, and by 21.4–33.1% due to transplanting in July compared with direct seeding in May-end/early June. The yield of direct-sown crop increased by using high-density seed of 22.9–23.0 mg weight (5.2–9.0%), higher seed rate of 600 m⁻² (2.2–2.3%) and basal fertilization at 40 kg N ha⁻¹ (19.4–25.7%) compared with low-density seed (19.4–20.1 mg), 400 seed m⁻² and no N, respectively. The yield of transplanted crop increased by using N-fertilized seedlings of 0.49–1.65 g weight (29.5–38.5%), higher number of seedlings at 155 m⁻² (3.5–16.7%) and basal fertilization at 40 kg N ha⁻¹ (31.9–32.5%) compared with unfertilized seedlings (0.19–0.79 g), 115 seedlings m⁻² and no N. Split application of 40 kg N ha⁻¹ — 50% each at basal and top dressing (105–115 days of growth after flash-flooding) — improved yield significantly (10.1–13.1%) over single basal application under simulated flash-flooding, but not under natural submergence conditions. Regression analysis indicated that relative contribution of various factors in increasing grain yield was in order: N fertilizer > seed density > seed m⁻² in direct-sown rice, and N fertilizer > seedlings m⁻² > seedling dry weight in transplanted rice. It was concluded that grain yield of flood-prone lowland rice can be increased by establishing the crop early through direct seeding using high-density seed and basal N fertilization.     

The effect of increasing NaCl in irrigation water on growth,gas exchange and yield of tobacco Burley type

Despite the economic importance of tobacco, there is limited field study on the quantitative response of growth and yield to increasing soil salinity. The effects of irrigation with saline water on yield components of field-grown tobacco (Nicotiana tabacum L.) “Burley” type plants were studied over two growing seasons. Growth, dry matter partitioning and gas exchange were measured either in rainfed or fully irrigated plants growing in a clayey–sandy–loam soil. The four fully irrigated treatments received amounts of saline waters at 0.54, 2.5, 5.0 or 10 dS m⁻¹ electrical conductivity (EC_w) equal to crop evapotranspiration. In both years, the electrical conductivity of the saturation phase (EC_e) across the 0.6 m topsoil profile increased with increasing salinity of the irrigation water. Soil moisture was markedly lower in the rainfed treatment than in fully irrigated treatments. Different saline concentrations of irrigation water had virtually no effect on soil moisture. Carbon assimilation rate, stomatal conductance and water use efficiency of the saline treatments were lower than the fully irrigated plants at 0.54 dS m⁻¹ (NW treatment) in 1996, but not in 1997. Transpiration rates were unaffected by salinity in both years. The highest yield was produced by plants irrigated with good quality water. The number of leaves per unit land area was greater for the NW plants, whereas there were no differences between the other four treatments. Salinity decreased plant dry matter and height at harvest, increased dry matter partitioning into leaves and decreased that into stems in both years. Dry matter partitioning to leaves was also greater for the rainfed plants than for the NW plants. Tobacco plants grown under field conditions showed a maximum reduction of relative yield at the highest salinity level of only 31%. The threshold values (0.56 and 0.96 dS m⁻¹) and the EC_e at which a 10% yield reduction was obtained (3.12 and 2.55 dS m⁻¹) calculated from the linear model of response of relative yield to increasing EC_e were typical of moderately sensitive crops. The EC_e values at which 50% yield was reduced (13.34 and 8.91 dS m⁻¹) were indicative of moderate tolerance to salinity.     

Optimization of High-Protein Glutinous Rice Flour Production Using Response Surface Method

A response surface method was employed to study the effect of α-amylase concentration, hydrolysis temperature and time on the production of high protein glutinous rice flour (HPGRF). The suspension of glutinous rice flour (15%) that contained 6.52% protein was gelatinized and subsequently hydrolyzed by thermostable α-amylase. The hydrolysis yielded 0.144–0.222 g/g HPGRF with 29.4%–45.4% protein content. Hydrolysis time exerted a significant effect, while enzyme concentration and hydrolysis temperature showed insignificant effect on the protein content and production yield of HPGRF. The result of response surface method showed that the optimum condition for the production of HPGRF that contained at least 36% protein was treating gelatinized 15% glutinous rice flour suspension with 0.90 Kilo Novo α-amylase Unit (KNU)/g α-amylase at 80 °C for 99 min. By carrying out the predicted hydrolysis condition, HPGRF with 35.9% protein and 61.8% carbohydrates was resulted. The process yielded 0.172 g/g HPGRF. HPGRF contained higher amount of essential amino acids compared to glutinous rice flour. HPGRF had higher solubility and lower swelling power, and also showed no pasting peak compared with glutinous rice flour.     

Acetosolv delignification of Miscanthus sinensis bark: Influence of process variables

Using a face-centred composite experimental design with three central point replicates, we investigated the effects of cooking time (60–180 min), acetic acid concentration (60–95% of liquor weight) and HCl concentration (0.05–0.15% of liquor weight) on the yield, residual Klason lignin content and total polysaccharide content of pulps obtained from Miscanthus sinensis bark by the acetosolv process. Response surfaces fitted satisfactorily to the experimental results showed the most influential of the independent variables to be acetic acid concentration; increasing acetic acid concentration reduced yield and lignin content, and increased total polysaccharide content (except at the highest concentrations of the acids). The response surface for lignin content was used to design a Box–Wilson steepest-descent optimisation procedure to determine the conditions minimising pulp lignin content; the minimum achieved, 0.5%, was obtained using a cooking time of 147 min, an acetic acid concentration of 93.25% and an HCl concentration of 0.122%, under which conditions pulp yield was 52.6%.     

Paper from olive tree residues

An experimental design was performed to study the influence of process variables (135–175 °C for temperature, 60–120 min for pulping time and 15–25% for active alkali) on the properties of pulps (yield, Kappa index, viscosity, 1% NaOH solubles, alcohol–benzene extractives holocellulose, lignin and α-cellulose contents and brightness) and paper sheets (stretch index, burst index, and tear index) obtained from olive trimming residues. Obtaining pulps with acceptably high physical and chemical properties entails operating at a temperature of 175 °C for 90 min and 25% of active alkali. The paper sheets obtained from olive trimming residues pulps that were produced in different degrees of refining are characterised for their stretch index, burst index, and tear index. An increase in the different parameters for the paper sheet upon increasing the degree of refining is found. All pulps reached between 33 and 39 kN m/kg in the stretch index, between 1.5 and 2 kN/g for the burst index and 0.7–2.5 N m²/g for the tear index and not in excess of the refining degree (<45 °SR).     

Genetic gains in grain yield and related physiological attributes in Argentine maize hybrids

Genetic gains in grain yield and related phenotypic attributes have been extensively documented in maize (Zea mays L.), but the effect of breeding on the physiological determinants of grain yield is yet poorly understood. We determined genetic gains in grain yield and related physiological traits for seven maize hybrids developed for the central region of Argentina between 1965 and 1997. Gains were expressed as a function of the year of release (YOR). Hybrids were cropped in the field at five stand densities (from almost isolated plants to supra-optimal levels) during two contrasting growing seasons (E₁ and E₂). Water and nutrient stress were prevented and pests controlled. Genetic gains in grain yield (≥13.2 g m⁻² YOR⁻¹) were mainly associated with improved kernel number, enhanced postsilking biomass production, and enhanced biomass allocation to reproductive sinks, but computed gains were affected by the environment. Differences among hybrids arose at the start of the critical period, and were evident as improved mean radiation use efficiency (≥0.026 g MJ⁻¹ YOR⁻¹), enhanced plant growth rate at near optimum stand density (≥0.04 g pl⁻¹ YOR⁻¹), and improved biomass partitioning to the ear around silking (0.0034 YOR⁻¹, only for E₁). Improved biomass production after silking was related to an increased light interception (≥4.7 MJ m⁻² YOR⁻¹), and allowed for an almost constant source–sink ratio during grain filling. This trend determined no trade-off between kernel number and kernel weight. In contrast to previous studies, genetic gains were detected for potential productivity (e.g., maximum grain yield) on a per plant basis (i.e., under no resource competition), a promising aspect for the improvement of crop grain yield potential.     

Ferulic and p-coumaric acids extraction by alkaline hydrolysis of brewer's spent grain

This work deals with the alkaline hydrolysis of brewer's spent grain (BSG) for the extraction of ferulic and p-coumaric acids, compounds of considerable interest for applications in the food, health, cosmetic, and pharmaceutical industries. A 2³ full factorial design with three replicates at the center point was used to investigate the simultaneous effects of the variables: NaOH concentration (1.0, 1.5 and 2.0%, w/v), temperature (80, 100 and 120 °C), and reaction time (30, 60 and 90 min), on the alkaline hydrolysis. The assays were performed using a solid:liquid ratio of 1:20 (w/w). The Student's t-test revealed a positive influence (p < 0.05) of all the studied variables on the ferulic and p-coumaric acids extraction from BSG. Linear models were well fitted (R² > 0.90) to the experimental data to describe the extraction of these acids as a function of the operational variables employed. The best alkaline hydrolysis conditions consisted in using a 2% NaOH concentration, at 120 °C for 90 min. Under these conditions, a liquor containing 145.3 mg/l ferulic acid and 138.8 mg/l p-coumaric acid was obtained. These values corresponded to 9.65 mg ferulic acid and 9.22 mg p-coumaric acid per gram of solubilized lignin.     

Alkaline sulfite–anthraquinone (AS/AQ) pulping of wheat straw and totally chlorine free (TCF) bleaching of pulps

Alkaline sulfite–anthraquinone (AS/AQ) pulping of wheat straw and totally chlorine free (TCF) bleaching of resulting pulps was investigated. Wheat straw was supplied by the Ferdosii University Experimental Station in Northeastern Iran, cleaned and chopped into about 3–5 cm long pieces. In the AS/AQ pulping experiments, the active alkali charge on oven dry wheat straw, heating time to maximum cooking temperature, AQ dose and liquor to straw ratio were kept constant at 16%, 60 min, 0.1% and 4/1, respectively. The alkali ratio, Na₂SO₃/NaOH, calculated as NaOH, was varied from 20/80 to 80/20. Cooking time at maximum temperature was varied from 30 to 90 min and maximum cooking temperature was adjusted between 152 and 160 °C. Reference soda and soda/AQ pulps were produced.AS/AQ and soda/AQ pulps with kappa numbers below 15 were produced easily. Cooking of corresponding soda pulps under comparable conditions stopped at a kappa number of 25. The characteristics of unbleached AS/AQ, soda/AQ and soda pulps were compared. AS/AQ and soda/AQ pulps had similar tensile strength but tear was in favor to AS/AQ. The latter had much higher yield and brightness.TCF bleaching of AS/AQ pulp was performed in O Q (OP) or O Q (OP) P sequences. Oxygen delignification (O) resulted in a delignification degree of approximately one third. Followed by a chelating treatment (Q) and a subsequent (OP) stage under drastic conditions a brightness of 82.7% ISO was achieved in an O Q (OP) sequence. The sequence O Q (OP) P, with 2% H₂O₂ in the final P stage, improved brightness from 77.2% ISO after the OP stage to 83.6% ISO. Bleaching led to only small losses in tensile and burst strength but enhanced tear strength. Short beating in a Jokro mill was sufficient to attain good pulp strength. The results of this study indicate that AS/AQ pulping and TCF bleaching is a convincing alternative to produce high-quality pulp from wheat straw for writing and printing paper.     

Breeding for perennial growth and fertility in an Oryza sativa/O. longistaminata population

The development of perennial cultivars (CVs) of upland rice would give farmers a new tool to reduce soil erosion from hilly fields, thereby mitigating a problem of regional concern in Southeast Asia. Oryza longistaminata is an undomesticated, perennial, rhizomatous relative of domesticated Asian rice (Oryza sativa). Using five sets of 4 × 2 factorial mating designs, we crossed rhizomatous interspecific genotypes (IGs) from an intermated O. sativa/O. longistaminata population with male-fertile IG selections from the intermated population, and with O. sativa CVs. Parents and progeny were planted in an upland field at IRRI using a randomized complete block design and evaluated for rhizome expression, survival after 1 year, vigor of the survivors, and yield. For the IG parents, rhizome expression was variable and penetrance of most genotypes was incomplete, but genotypes that demonstrated the potential for moderate rhizome expression had high penetrance (89% average). The CV parents yielded 11.0 g/plant on average but none produced rhizomes or survived 1 year. The IG parents averaged yields of 3.1 g/plant, 57% rhizomatous and 36% survival. The IG/IG progeny averaged yields of 4.2 g/plant, 32% rhizomatous and 37% survival. The IG/CV progeny averaged yields of 6.0 g/plant, 18% rhizomatous and 16% survival. Nine IG/IG progeny and six IG/CV progeny were rhizomatous, perennial, and yielded at least 5 g/plant, and five of these yielded more than 10 g/plant. For the IG parents and IG/IG progeny, rhizome presence and expression were positively associated with survival and vigor of the survivors. General combining ability effects were significant for percent survival and yield but not percent rhizomatous. Specific combining ability effects were significant for percent rhizomatous, percent survival and yield. By selecting female parents for long rhizomes and male parents for fertility, considerable gains in rhizome expression, survival and yield were made. The development of perennial upland rice CVs should be feasible via introgression of genes from O. longistaminata.     

Effect of growth regulators on yield and fiber quality in ramie (Boemheria nivea (L.) Gaud.), China grass

The effects of two mixtures of four plant growth regulators (choline chloride, gibberellin (GA₃), benzyladenine (6-BA) and NaHSO₃) at 20:9:5:800 mg kg⁻¹ (H1) and 20:42:43:2350 mg kg⁻¹ (H3) (active ingredients), respectively, were investigated on yield and fiber quality in ramie (Boehmeria nivea (L.) Gaud.). The mixtures were sprayed over the canopy at two growth stages (10 and 20 days after the previous cut) of field-grown ramie. The treatments increased raw fiber yield by 13–18%, and improved fiber fineness by 57–349 m g⁻¹, increased number of leaves per plant, and also improved all yield components. Treatment H1 resulted in a denser distribution, smaller diameters and greater quantity of fiber cells in stem cross-section. Physiological responses included improving leaf water status, increasing net photosynthetic rate, and decreasing electrolyte exosmosis rate.