互花米草化学性质和纤维形态分析

对不同生长时期的互花米草的化学性质和纤维形态进行测定与分析,结果表明:随生长期的增长,互花米草综纤维素与木质素含量逐渐增加,而各种抽出物含量呈减少趋势,成熟的互花米草综纤维素含量与马尾松木材相近.秆部位的综纤维素和木质素含量最高;互花米草原料pH值呈中性或弱碱性,秆部位酸碱缓冲容量最低,梢部位则较高;互花米草秆部位的表皮和叶部位二氧化硅含量较高.互花米草纤维属于中等长度纤维,纤维大小等级为细.     

Water sorption,surface structure and surface energy characteristics of wood composite fibres refined at different pressures

During fibre processing, wood fibres are subjected to a range of physical and chemical conditions sufficient to slightly alter their chemical composition and hence their ultimate performance when used in the manufacture of wood fibre-based composites. In order to better understand the effects of refiner conditions on material performance, wood fibres were subjected to processing at different refiner pressures (4, 6, 8 and 10 bar) and subsequently dried in a flash drier. The fibres were analysed for changes in surface area, surface energy, surface structure and water vapour sorption characteristics. The methods applied were nitrogen adsorption utilising the Brunauer–Emmett–Teller theory, inverse gas chromatography, scanning electron microscopy and dynamic vapour sorption. It was found that increasing refiner pressure resulted in fibres of lower surface area, accompanied by increasing dispersive surface energies up to operating refiner pressures of 8 bar. It was found with fibres refined at different pressures that as the refiner pressure increased the equilibrium moisture content of the fibre decreased at the set relative humidities. However, it was also noted that the hysteresis was not significantly different between each of the refiner pressures. The results suggest that different refiner pressures can be used to tune the surface characteristics which may be beneficial to product development and the improvement of the environmental profile of the wood fibre composites.     

Patterns of variation in chemical compositions of wood from natural populations of Pinus manssoniana Lamb. in Guizhou Province, China

Patterns of variation in the chemical composition of wood,i.e.,holocellulose,cellulose and lignin contents and 1%NaOH extractives were studied in 12 natural populations of Pinus manssoniana Lamb.in Guizhou Province,China,using wood cores as experiment material.The results show statistically significant differences among provenances in holocellulose,cellulose and 1% NaOH extractive contents.The largest coefficient of variation among the provenances was found in the 1%NaOH extractive content and the smallest in the holocellulose content.Variation of lignin content occurred within provenances.Correlations between chemical compositions of wood and factors of local geography and meteorology were largely insignificant.The chemical composition of wood presented patterns of random variation.The correlation of 1%NaOH extractive content with holocellulose content was significant(r=?0.68).There was also significantly negative correlation(r=0.62)between cellulose and lignin content.On the basis of a UPGMA cluster analysis,we identified three provenances of masson pine among the 12 studied,i.e.,those of Wengan,Tongzi and Luodian with high cellulose contents,low levels of 1%NaOH extractive and moderate lignin contents,which we recommend as promising provenances for growing of pulp wood and the manufacture of paper in Guizhou Province     

真菌致泡桐材组分变化研究

用FTIR、ESCA等波谱分析方法，对真菌侵蚀的泡桐材进行了分析，结果表明：真菌侵蚀后，泡桐材的木质素含量相对比例增加、半纤维素含量降低、纤维素含量变化不明显。     

檫树人工林和天然林木材纤维形态和化学成分的比较研究

通过对檫树人工林和天然林木材纤维形态和化学成分的测定和比较分析 ,结果表明 :檫树人工林木材纤维长度和长宽比小于天然林 ,宽度大于天然林 ;纤维素、戊聚糖和木素的含量均稍高于天然林 ,灰分和抽出物含量均低于天然林     

古建木构件化学组分近红外光谱分析

在材种鉴定的基础上,通过近红外光谱(NIRS)定性分析了建成约600 a的木造古建筑木构件的化学组分,结合木构件化学组分定量分析,与现代木材相比较,探讨了近红外光谱技术评价木构件老化的可行性。结果表明:近红外二阶导数特征性谱带反映了木材纤维素以及半纤维素和木质素的基团信息,而其差谱反映出木构件与对照样化学组分变化。这些光谱特征与传统的化学组分定量分析的结果非常一致:纤维素和半纤维素相对含量减少而木质素相对含量增加,与各种组分谱带差谱的增减相对应。此外,在5 882,5 587和5 464 cm-1等谱带处反映的纤维素结晶和半结晶区的光谱信息,差谱观察到木构件与现代材落叶松之间化学组分的不变或减少,其结果与X射线衍射(XRD)方法获得的木材结晶度分析结果相一致。通过NIRS定性分析木构件化学组分及结晶度变化,接近于现场检测方法,使用便携式NIRS,在古建筑木构件端头裸露部位获取光谱信息,能够实现现场对木材化学组分的无损定性评价。本实验结果也表明,除了常规的红外光谱(FT-IR)、XRD分析技术,NIRS技术对于木构件老化状况的评价是一种有潜力的无损检测方法。     

Characterization of mean stem density,fibre length and lignin from two Acacia species and their hybrid

The objective of this study was to compare the wood properties related to wood pulp quality of two widely planted Acacia species viz.Acacia mangium Willd.and Acacia auriculiformis A.Cunn.Ex Benth.and their hybrid.Acid insoluble lignin content(Klason),mean stem density and fibre length differed considerably among the species and hybrids.A.mangium possessed a high percent of lignin content compared to A.auriculiformis and the Acacia hybrid.However,mean stem density of A.auriculiformis was higher than A.mangium and the hybrid.Fibre length of heartwood tissues was generally shorter than that of sapwood tissues.The hybrid had longer fibres than the parent species.Lignin was negatively correlated with mean stem density.Generally,the wood properties of the hybrid were superior to its parent species.The significant intraspecific variation observed for wood properties of Acacia species could be used in breeding superior hybrids combining desirable traits of the two species.Considering thedifficulty involved in accurately measuring the lignin content compared to mean stem density,selection for plants with low lignin content can be achieved by indirect selection of high mean stem density.     

Nanocellulosic fillers for waterborne wood coatings: reinforcement effect on free-standing coating films

Coatings fulfill an important function in providing functionality and service life to wood surfaces. In the present study, the potential of nanocellulosic fillers toward improving waterborne wood coating mechanics is evaluated using free-standing coating films. At 2% filler content, significant improvements in static and dynamic mechanical properties were observed. The extent of these improvements was different depending on whether high-aspect-ratio cellulose nanofibrils of short cellulose nanocrystals were used. Chemical surface modification of cellulose nanofibrils did not provide further improvement. The water–vapor sorption properties of the coating films, which were also evaluated, did not show significant effects due to addition of nanocellulose, while optical transparency slightly decreased.     

Limitation of XPS for analysis of wood species containing high amounts of lipophilic extractives

Chemical composition of Norway spruce and pine, two softwood species, has been investigated by X-ray Photoelectron Spectroscopy (XPS). Contrary to results previously obtained with beech wood, which allow to obtain information on bulk chemical composition from surface composition analysis, XPS analysis appears to be unsuitable for the characterisation of Norway spruce and pine wood chemical composition. Indeed, chemical compositions calculated from XPS data differ strongly from those obtained from microanalyses which are in good agreement with theoretical composition described in the literature. XPS analysis of both the softwood surfaces indicated high carbon contents explained by migration of lipophilic extractives to the surface under the influence of the vacuum necessary for XPS analysis. Nonvolatile extractives contained in wood were extracted and deposited on glass plates and analysed. Survey and detailed C1s spectra indicated similar signals to those recorded on wood surfaces. This phenomenon was not observed when samples had been previously extracted before analysis. These results strongly evidenced that extractives present in both species are able to migrate through resin canals from the bulk of the sample to the surface when put into ultra high vacuum. XPS presents, therefore, some limits in the case of the analysis of softwood species containing extractives able to migrate to the surface during analysis. This behaviour, difficult to control, could lead to erroneous interpretations due to extractives enrichment of the surface under the effect of vacuum.     

Degradation of wood surfaces during natural weathering. Effects on lignin and cellulose and on the adhesion of acrylic latex primers

Summary Radiata pine veneers and blocks were exposed to natural weathering under Australian summer conditions over a period of 30 days. Infrared spectroscopy revealed that there was perceptible surface delignification after 4 hours exposure, substantial surface delignification after 3 days exposure and almost complete surface delignification after 6 days. Rapid lignin degradation was also suggested by measurements of the acid insoluble lignin content of weathered veneers. Viscometry determinations on holocellulose samples from weathered veneers and unweathered controls indicated significant depolymerisation of cellulose after 4 days exposure. A tape test was used to assess the adhesion of acrylic latex primers to weathered blocks. The adhesion of exterior acrylic primers decreased on weathered wood surfaces and was significantly lower on specimens that were weathered for 5 to 10 days. An oil-modified acrylic primer showed greater adhesion to weathered wood surfaces. Primer adhesion was lower on weathered radial surfaces than on similarly exposed tangential surfaces. The practical implications of these findings for the coating of exterior wood with acrylic latex primers are discussed briefly.The authors wish to thank Dr. A. J. Michell for FTIR spectral determinations and the Australian Research Council small grants scheme for financially supporting part of the work     

白桦木材生物制浆的木材腐朽菌菌种选择

采用5种木材腐朽菌,分别对30株天然林白桦木材进行木材腐朽处理,检测并比较腐朽木材和新鲜木材中未质素、纤维素等主耍化学成分的变化。结果表明,木蹄层孔菌腐朽后的白桦木材其重量、木质素和纤维素损失率最高,桦剥管菌次之,白囊耙齿菌最低;木蹄层孔菌腐朽后的白桦木材纤维素含量略高于新鲜白桦木材,其他4种茵腐朽后的白桦木材纤维素含量都低于新鲜白桦木材,其中桦剥管菌和彩绒革盖菌腐朽后的白桦木材纤维素含量较低。木蹄层孔菌腐朽后的白桦木材1％NaOH抽出物含量最低,苯醇抽出物含量中等,纤维素含量最高,木质素含量较低,相比之下它腐朽白桦木材的能力较强,适用于以白桦木材为原料的生物辅助造纸。     

Chemical composition of wood and its connection with wood anatomy in Betula pubescens

ABSTRACT

The connection between chemical composition and anatomy of wood is poorly studied. Abiotic and biotic growth conditions affect the synthesis of structural compounds and the anatomy of wood at the same time as they affect growth. In this study, the wood chemical composition, and connections between wood chemistry and anatomy were studied in downy birch (Betula pubescens Ehrh.) grown on four growth sites possessing mineral and peat soils. Lignin, holocellulose, extractive and ash contents, and effective heating value were analysed and compared with libriform fibre double wall thickness and lumen diameter, vessel size and number, and ray and axial parenchyma numbers. Measured lignin and extractive contents were exceptionally high and holocellulose content low. Correlations between wood anatomy and effective heating value were partly different on different soils. Correlations between holocellulose and anatomy were the opposite of the correlations between other chemical compounds and anatomy. The significant correlations between chemical composition and anatomy were commonly opposite in trees grown on peat than in trees grown on mineral soil. Particularly, vessel characteristics and fibre wall thickness correlated significantly with wood chemistry in trees grown on mineral soil. The connections between wood anatomy and chemistry proved to be soil-dependent.     

马尾松木材化学组分的遗传控制及对木材育种的意义

本文利用 1 3年生马尾松子代测定林的 2 0个自由授粉家系的木材试样 ,着重研究木材化学组分的遗传学问题。研究结果表明 ,木材化学组分、基本密度和生长性状在家系间的差异都达到了极显著水平 ,并受中等至强度的遗传控制。在 6个木材化学组分中 ,灰分、戊聚糖和 1 %NaOH抽出物含量的遗传力较高 ,木质素、综纤维素和热水抽出物含量的遗传力稍低。生长性状与木材密度呈显著的负相关 ,而与木材化学组分相关性很小 ,似相互独立。遗传相关认为灰分和热水抽出物含量可分别作为综纤维素和木质素的间接选择指标。由于综纤维素和木质素含量在家系间的绝对差异较小 ,仅为 2 %～ 3% ,对选育的实际意义不大。可选择综纤维素含量高的优株进行无性繁殖加以利用     

我省引种的任豆木材纤维形态初步研究

试验表明：任豆（Ｚｅｎｉａｉｎｓｉｇｎｉｓｃｈａｎ）的木材纤维形态具有明显的阔叶材特征。其纤维平均长度为１．０１ｍｍ,纤维宽度为２３．１μｍ,长宽比为４３．７;其纤维素含量达５０．１１％,属于高含量的范畴,而木素含量为２２．０１％,则在中等水平。     

Effect of the presence of lignin on the structure and reactivity to hydrolysis of lignincarbohydrate complexes of poplar wood obtained by sulfate pulping

Summary Lignincarbohydrate complexes (LCC) of poplar wood obtained by sulfate pulping and containing lignin in amounts of 0.9–8.3% have been studied by X-ray diffractometry. Heterogeneous hydrolysis methods have been used to determine their reactivity. The content of the crystalline fraction in LCC depends on the lignin removal and increases with the decrease of the lignin content. The degree of crystallinity of cellulose in sawdust and in LCC is fairly high and changes slightly with the lignin removal. The presence of lignin plays a blocking role in the heterogeneous hydrolysis and decreases the rate constant. It is suggested that lignin is bonded to cellulose on the outer surfaces of the crystalline part of the cellulose fibril. Some possible variants of these bonds are discussed.     

杨木应拉木微区结构可视化及化学成分分析

木材微区结构与木材宏观性质密切相关,杨木应拉木与对应木宏观性质存在较大差别,探究杨木应拉木和对应木微区结构和化学成分,可为了解杨木应力木的宏观性质提供理论根据。借助光学显微镜、荧光显微镜、显微拉曼成像光谱仪、透射电镜对杨木应拉木微区结构进行可视化研究,并借助X射线衍射技术和美国可再生能源实验室方法,分析杨木应拉木的微晶尺寸、结晶度以及化学成分。结果表明:杨木应拉木中应拉区和对应区纤维细胞微区结构差异显著。光学显微镜下显示应拉区木纤维中胶质层清晰可见,荧光显微镜和拉曼显微镜下显示胶质层的木质素浓度比对应区低。透射电镜下显示应拉区木纤维细胞壁结构由初生壁、次生壁和胶质层组成,未见次生壁外层,各层的平均厚度分别为0.61,1.22和2.53μm。对应区木纤维为典型的初生壁和次生壁结构,次生壁各层平均厚度分别为0.33,2.28和0.14μm。杨木应拉区纤维素含量(58.91%)比对应区(41.53%)高,木质素含量和半纤维素含量均比对应区的低,应拉区木质素和半纤维素含量分别为21.99%和12.01%,对应区分别为28.10%和17.08%。杨木应拉区结晶度(48.06%)比对应区(41.01%)高,应拉区晶区宽度为2.66 nm,长度为8.84 nm;对应区晶区宽度为2.65 nm,长度为9.87 nm。     

Studies on opposite wood in conifers Part I: Chemical composition

Summary Opposite wood, normal side wood, and compression wood were isolated from leaning stems of Abies balsamea, Larix laricina, Picea mariana, Pinus resinosa, and Tsuga canadensis and were subjected to analyses for lignin and relative carbohydrate composition. There were no statistically significant differences between the data obtained for opposite wood and side wood. Contrary to some earlier reports, opposite wood has exactly the same content of lignin, cellulose, and hemicelluloses as has corresponding normal wood.This paper is dedicated to Dean Edwin C. Jahn in honor of his 70th birthday.     

白桦木材侵染菌侵染材的化学分析

白桦木材在自然和人工干燥过程中易受真菌类微生物的侵染产生色变,在一定程度上降低了白桦木材的加工利用价值。本文针对白桦木材侵染菌侵染试材的化学成分变化进行分析,以期为白桦木材生物变色防治提供参考。首先对白桦木材侵染菌进行分离、纯化与鉴定,确定侵染白桦试材的侵染菌的基本类型,然后进行白桦试材接菌,最后对白桦侵染菌侵染木材的化学成分进行测定。结果表明,与未侵染素材相比,侵染菌侵染试材中苯醇抽提物含量、1%NaOH抽出物含量、热水抽出物含量和多戊糖含量均较高,而纤维素及木素含量较低。这表明侵染菌在适宜的条件下会侵蚀白桦木材细胞壁组织,造成纤维素和木素等主要成分含量的降低,导致木材组分的破坏。同时,侵染菌的存在会造成白桦木材抽提物组分中的显色及助色物质的含量变化,以致木材产生不同程度的变色。     

The use of near-infrared scanning for the prediction of pulp yield and chemical properties of Pinus patula in the Mpumalanga escarpment area of South Africa

Near-infrared (NIR) scanning technology is regarded as a potential tool for rapid determination of wood properties, which can substitute time-consuming and costly traditional methods. Pinus patula is the most important softwood species in South Africa, and this study is aimed at developing NIR calibration models for quick prediction of its pulp yield and chemical composition. A total of 85 trees from 17 plots, covering the range of site conditions in the Mpumalanga escarpment area, were sampled. Two samples were taken from each tree: a 1 m billet above breast height and a 20 mm disc at breast height. The billet was pulped using the kraft pulping process to determine pulp yield. The disc was ground into sawdust and the chemical composition was determined using conventional wet chemistry. Sawdust was scanned on a NIR spectrophotometer to produce NIR spectra. Calibration models to predict pulp yield, cellulose and lignin content were developed by applying chemometrics and partial least squares regression. Validation and determination of prediction accuracy of the models were performed using independent data. The prediction of cellulose and lignin were acceptable with correlations of determinations (r ²) of 0.71 and 0.70 respectively. Standard errors of prediction were generally low (less that 0.86) for all the models. The prediction r ² for both total and screened pulp yield were only 0.62. Although the cellulose and lignin models can be used with confidence, the expansion of the sample size for follow-up research must be considered in order to increase the variability of tested wood properties and improve the prediction strength of the models. The NIR calibration provided in this study can contribute to the efficient examination of forest site-to-wood quality relationships that would enhance precision forest management and wood processing efficiency.