Topology Analysis of Phase-shifted Full-bridge Soft-switching Converter

Phase-shifted full-bridge(FB) soft-switching converters are developing form the basic phase-shifted FB-ZVS-PWM converter to phase-shifted FB-ZVZCS-PWM converter and phase-shifted FB-ZCS-PWM converter,to a series of the other new phase-shifted full-bridge circuits,which make up of the converters with developmental and useful foreground.The topology structures,operation characteristics,as well as their merits and demerits are compared and analyzed.The improved phase-shifted FB-ZVS-PWM converter enlarge the load range of ZVS in lag-arm.Phase-shifted FB-ZVZCS-PWM converter solves the problem mentioned above,and insulated gate bipolar transistor(IGBT) is fit for the lag-arm.Phase-shifted FB-ZCS-PWM converter could achieve ZCS in every power tube,and is used in high-power occasion.What's more,the developmental trend of soft-switching converting technic without resonance network is pointed out.     

Zero Current Switching Multi-resonant Converters based on ConstantFrequency PWM and Mutual Inductance Technique

This paper introduces a novel constant frequency switching PWM converter,as well as some improvements on the conventional bridge parallel resonant converters. By introducing mutual inductance and auxiliary into the original circuit topology ,a class of novel zero current switching multi-resonant converters regulated by PWM mode at a fixed switching frequency are presented,which overcomes some drawback of the original circuits.One illustrative example is analyzed and the experimental results are given, which confirms the advantages of this approach.     

Soft-switching Analysis Phase-Shifted-FB-ZVS-PWM DC-DC Converter With Saturable Inductor

Compared with the traditional full-bridge(FB)zero-voltage-switched(ZVS) pulsewidth-modulated(PWM) converter, the FB-ZVS-PWM converter with a saturable inductor has a wider load range with ZVS and smaller circulating energy as well as smaller duty cycle loss. By analyzing the operation principle of the converter, this paper studies design considerations of the parameter bringing about ZVS and dead time of the switch, and gives out the design method, finally simulation testing has been carried out.     

Passive Lossless Forward Converter with Current Double Rectifier

To reset transformer excitation flux reliably,reduce the switching losses and improve influence of EMI noises in high frequency forward converters,several kinds of methods have been proposed,including RCD snubbers,active snubbersand resonant converters,and so on.These methods have many shortages.In consideration of these shortages,this paper puts forward a passive lossless forward converter with current double rectifier(CDR).The circuit does not require an extra switch or additional control circuit,and can resets the transformer excitation flux reliably,and does not include lossy components.So the circuit has higher reliability and higher performance/price ratios than above several kinds of methods. The paper analyzes the frame and operating principle of main circuit in detail.The key parameters design principles of the circuit are given.The simulation results confirm validity of the theoretical analysis results.     

Research on a Novel Inverter of VSC

In order to improve waveform performance of light HVDC system, a lot of switches which operate in high frequency are used, which causes large switching losses and results high cost. A new Buck type voltage source converter(BVSC) is proposed. The new BVSC comprises a dual-buck converter and a three-phase inverter operating in grid frequency. Only two high frequency switches are used, which results good output waveform performance. In order to reduce the high frequency switching losses, a novel improved double-frequency Buck type voltage source converter(DBVSC) is also proposed. An additional dual-Buck converter is added to the BVSC, the added dual-Buck converter deals with the fundamental power that operates in low frequency, and BVSC only deals with harmonic power that operates in high frequency. The output waveform is enhanced and the switching losses are reduced in DBVSC, and the power rating is also increased. The DBVSC is very suitable for large power rating application. The one cycle control theory is adopted to control the proposed DBVSC with analog circuit, which is very simple. The proposed DBVSC and control method are verified by simulation.     

Analysis,Modeling and Simulation of the Phase shift Full Bridge Zero-Voltage-Switched PWM Converter

Based on the analysis of the phase shift Full Bridge Zero Voltage Switched PWM Converter(FB ZVS PWM converter),a smal signal model is derived,and simulation results of frequency domain and time domain are given.[WT5HZ]     

Dual mode AC DC AC converter for contactless power transfer system

A new type AC DC AC converter which can work in Buck or Boost mode is proposed in order to overcome the deficiencies of the primary circuit of the traditional contactless power transfer system. Through switching this two modes and turning the duty cycles of the switches, not only the resonant current amplitude of the primary resonant current can be controlled to be constant against a wide range variation of input voltage, but also the problems, such as surge current, high cost, complex control etc., caused by the DC filter and DC/DC converter in a traditional CPT system are effectively eliminated. The topology and operation principle of the proposed converter have been analyzed. The corresponding control strategy has been presented and verified by simulation results.     

Parameter design and simulation for animproved direct current side active power filter

Considering the characteristics of the dc side series active power filter (APF) that the output voltage cannot be adjusted and the control circuit is complex , an improved single phase dc series APF topology is proposed. The improvement of the new circuit topology and fundamental working principle are analyzed. Following the circuit power factor pre regulator principle, the designing method for the main circuit parameters is given. The voltage ring and the current ring are designed by using the zero pole method. The main circuit power switch is controlled with the same frequencies, while the control circuit was simplified further. Compared with the paralleled APF, the main circuit of topology structure is simplified and the number of the active switches is reduced, which show low input current harmonics, high power factor, large voltage output adjustment range and low cost. The simulation results prove that the proposed topology is correct and reliable.     

A NEW COMPENSATIVE SNUBBER FOR ELIMINATING THE SURGE AND NOISE IN PWM CONVERTERS

A new compensative snubber is presented for eliminating the surge current and high frequency parasitic oscillation in rectified circuit of the PWM DC-DC converters. The output surge and noise voltages are de-creased over 4/5. The working principle of the sunbber is analyesd in detail, the designing formulas are derived. The theoretic analysis is consistent with the experimental results.     

Full bridge LLC series resonant converter for X-Ray high voltage DC power supply

To prevent the duty cycle loss of full-bridge converter controlled by the phase-shifting method, a high frequency high voltage X-ray power supply is proposed. It combines full bridge LLC(FB-LLC) series resonant converter with bipolar single-phase symmetrical voltage multiplier. FB-LLC series resonant, high voltage transformer and bipolar single-phase symmetrical voltage multiplier are used in the main circuit. The LLC series resonant circuit and working conditions of soft switch are analyzed. The fundamental harmonic approximation model is established. The parameters of the main circuit are designed. The simulation results show that the output voltage adjusted continuously within 40~120 kV and without duty cycle loss. The X-ray power supply is proposed to achieve a quick rise and low ripple of output voltage. According to the simulation results, the proposed topology is correct and reliable.     

Analysis of Equilibrium Runing Lines of Engine and Hydraulic Torque Converter for a Vehiele with CVT

The mathematical model of the torque converters is established based on test results. Equilibrium running lines of engine and hydraulic torque converter are analyzed. The idea of matching and controlling is put forward for CVT vehicle with torque converter in starting ability, crawl ability and fuel economical efficiency, which lays a foundation for the exploitation of CVT vehicle with torque converter.     

LCL型CPT系统的参数设计方法及频率特性分析

以金鲳鱼为原料,固定小麦粉与水的质量比为2∶1,食盐添加量2%,微波真空度0.095 MPa,在单因素试验的基础上,通过正交试验对微波真空技术膨化鱼糜饼工艺条件进行优化。结果表明,鱼糜饼制作的最佳工艺条件为:鱼糜含量35%,膨化温度100℃,膨化时间20 min,鱼糜饼厚度2 mm,在该工艺条件下,制得的膨化鱼糜饼色泽金黄、质地酥脆、风味清香,成品膨化率可达到540%。     

改进二次型Boost变换器的研究与分析

传统二次型Boost变换器具有较高的升压能力,但其开关器件的电压、电流应力较大,增加了电路的体积与成本。笔者在传统二次型Boost变换器的基础上,结合高增益Boost三端网络,提出改进二次型Boost变换器,并对其连续工作模式下的工作原理及各开关器件的电压、电流应力进行了分析。分析结果表明,改进二次型Boost变换器不仅升压能力有所提升,而且在输出电压相同的情况下,开关器件的电压、电流应力有所降低。最后,通过仿真分析验证了该变换器的正确性和可行性。     

The Stability Analysis of Single end Flyback Switching Power Supplies

Based on the research of a practical project for high hrequency high voltage switching power supplies,the state space average model as well as the transfer function of single end flyback converters,which can be used to analyze the stability of single end flyback switching power supplies,are established.     

A dual-boost three-phase DC link active power filter based on coupled impedance

A three-phase DC link active power filter (APF)based on coupled impedance and its control strategy are proposed in order to eliminate the input current harmonics of the three-phase diode rectifier. The presented APF is composed of impedance network and two asymmetric dual Boost converters. Average current control is adopted to control the DC link APF. The switch signals of the two asymmetric Boost converters are obtained respectively by leading and trailing edge modulation methods. Compared with the normal DC link active power filter,this topology reduces an active switch and a capacitance. So it can reduce costs,and there is no voltage imbalance in the DC link. Simulation results verify the correctness of the proposed topology and the corresponding control method.     

Design of converter of DC-AC type contactless power transfer system

A new type of circuit topology for DC-AC type contactless power transfer(CPT) system is proposed, and the asymmetric DC-AC convert is used to imply the new topology. The topology simplifies the circuit and control of DC-AC type CPT system, reduces the power loss of power conversion of secondary circuit, and improves the overall efficiency and power density of the system. This paper presents the topology of the converter and investigated its control strategy. A model of the system has been derived, with which the system is simulated and studied. The measured experimental results have verified the theoretical and simulation results.     

The modeling and simulation of a new USBCAN bus converter in Stateflow

The USBCAN bus converter is a connector of USB bus and CAN bus.It is difficult to judge whether the device works well or not and meets design requirement or not by ordinary ways.Regarded the Matlab/Simulink/Stateflow toolbox as the platform,the model of a USBCAN bus converter is established.The model of the bus converter is tested and verified in the Matlab/Simulink simulation environment.The results of the simulation analysis show the model is suitable for simulating the working state of the device.A new simulation and judging method for bus converters is proposed.     

Comparative study of aircraft three-phase power factor corrections

This paper summarizes the requirements of standards for aircraft power supply firstly,and then points out that the input current harmonic and output DC voltage ripple should be considered seriously when designing three-phase power factor correction (PFC)for aircraft under variable line frequency and unbalanced line supply. Based on reviewing the topologies for aircraft three-phase PFC,three typical topologies,i.e. three-phase pulse width modulation (PWM)rectifier,traditional shunt active power filter (APF)and generalized APF,are picked up. A unified single-phase equivalent model is developed for comparing the harmonic suppression performance of the three active PFC schemes. And the switching stress is also calculated for evaluating their efficiency and power density. Three 5 kW PFC are designed by employing each of the three selected schemes. Simulation is carried out to verify the correctness of the theoretical analysis. The theory and simulation results indicate that the generalized APF topology shows the most technical merit for aircraft three-phase PFC. Future research works on generalized APF are also pointed out,which are solving the uncontrollability of its DC output voltage and optimal designing the filter inductors.     

The power-supply of X-ray machine adopting PID control and high-frequency inverter technology

To solve the problem of low control accuracy and low stability of current X-ray machines, a kind of digital power supply for X-ray machine is introduced. In the digital power supply, some key technologies are used to improve the output stability of the high frequency inverter, including improved BUCK circuit for voltage regulating circuit, high frequency inverter and soft switching technology for the high-voltage generator. The PWM control technology is used to control the switch transistor of voltage regulating circuit and inverter circuit, which makes the drive waveform output stable and easy to control. In order to improve the control accuracy, reduce the volume and change high voltage consecutively, the software PID of the microcomputer is used to control the feedback circuit. The high-accuracy power chip is used for the filament power supply to make the filament electric current stable. Through the analysis of the circuit, the parameters of the circuit are calculated and the circuit is simulated by PSPICE software. The results show that the theoretical analysis is consistent with the practical simulation results. The design can meet the requirement of the technology indices of the power supply of the X-ray machines.     

Three-Effect Catalytic Converter of Vehicle Exhaust and the Latest Development

How to control exhaust of vehicle has become a hot topic in China. In the system of out engine's purification, a three-effect catalytic converter should be the preferential technique undoubtedly because of its maturation and reliability. All new Chinese cars have been now installed a three effect catalytic converter which is imported. However it is not able to hold up a national automobile industry. China should seek its own three effect catalytic converter to fit the specific situation. This paper expounds harm of the exhaust, configuration, catalytic theory, manufacturing processes, deactivation mechanism and others like that on the converter. Particularly, it discuses its demands and some approaches to satisfy ones. Out of that, how China should develop a catalytic converter is indicated which is suitable for the present situation.