Determining Wheat Dough Mixing Characteristics from Power Consumption Profile of a Conventional Mixer

A Hobart mixer with a pin‐type attachment was used to mix soft wheat flour dough. Power consumption profiles were measured continuously during mixing for 20 min using a current transducer and a data logging system. Experimental variables were quantity of flour (500, 1,000, and 1,500 g of dry wheat flour), water content (43, 45, and 47%, wb), and mixer speed setting (low, medium, and high). The power consumption profiles were evaluated by moving average and spectral analysis. Peaks in the power consumption profiles were located to determine the optimal mixing time. The optimal mixing times were then compared with storage and viscous moduli measured using a dynamic rheometer to assure the maximum strength of wheat dough at the optimal mixing time. Tolerance was determined using the signal amplitude and phase angle data from spectral analysis. Optimal mixing times of various doughs at medium speed ranged from 510 to 850 sec; low and high flour quantities required longer mixing times than medium quantity of flour. The optimal mixing time increased when the moisture content was lowered. Tolerance was affected by mixing speed and moisture content of flour     

Impact of Bran Addition on Water Properties and Gluten Secondary Structure in Wheat Flour Doughs Studied by Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy

The aim of this work was to elucidate the underlying physical mechanism(s) by which bran influences whole grain dough properties by monitoring the state of water and gluten secondary structure in wheat flour and bran doughs containing 35–50% moisture and 0–10% added bran. The system was studied with attenuated total reflectance (ATR) FTIR spectroscopy. Comparison of the OH stretch band of water in flour dough with that in H₂O‐D₂O mixtures having the same water content revealed the formation of two distinct water populations in flour dough corresponding to IR absorption frequencies at 3,600 and 3,200 cm^–1. The band intensity at 3,200 cm^–1, which is related to water bound to the dough matrix, decreased and shifted to lower frequencies with increasing moisture content of the dough. Addition of bran to the dough caused redistribution of water in the flour and bran dough system, as evidenced by shifts in OH stretch frequency in the 3,200 cm^–1 region to higher frequencies and a reduction in monomeric water (free water). This water redistribution affected the secondary structure of gluten in the dough, as evidenced by changes in the second‐derivative ATR‐FTIR difference spectra in the amide I region. Bran addition caused an increase in β‐sheet content and a decrease in β‐turn (β‐spiral) content. However, this bran‐induced transconformational change in gluten was more significant in the 2137 flour dough than in Overley flour dough. This study revealed that when bran is added to flour dough, water redistribution among dough components promotes partial dehydration of gluten and collapse of β‐spirals into β‐sheet structures. This transconformational change may be the physical basis for the poor quality of bread containing added bran.     

Comparison of Quality Characteristics and Breadmaking Functionality of Hard Red Winter and Hard Red Spring Wheat

Various whole‐kernel, milling, flour, dough, and breadmaking quality parameters were compared between hard red winter (HRW) and hard red spring (HRS) wheat. From the 50 quality parameters evaluated, values of only nine quality characteristics were found to be similar for both classes. These were test weight, grain moisture content, kernel size, polyphenol oxidase content, average gluten index, insoluble polymeric protein (%), free nonpolar lipids, loaf volume potential, and mixograph tolerance. Some of the quality characteristics that had significantly higher levels in HRS than in HRW wheat samples included grain protein content, grain hardness, most milling and flour quality measurements, most dough physicochemical properties, and most baking characteristics. When HRW and HRS wheat samples were grouped to be within the same wheat protein content range (11.4–15.8%), the average value of many grain and breadmaking quality characteristics were similar for both wheat classes but significant differences still existed. Values that were higher for HRW wheat flour were color b*, free polar lipids content, falling number, and farinograph tolerance. Values that were higher for HRS wheat flour were geometric mean diameter, quantity of insoluble polymeric proteins and gliadins, mixograph mix time, alveograph configuration ratio, dough weight, crumb grain score, and SDS sedimentation volume. This research showed that the grain and flour quality of HRS wheat generally exceeds that of HRW wheat whether or not samples are grouped to include a similar protein content range.     

Potential of Triticale as a Substitute for Wheat in Flour Tortilla Production

The potential of triticale as a partial or total substitute for wheat in flour tortilla production was evaluated. Different mixtures of triticale and wheat flours were tested in a typical hot‐press formulation. Both grains yielded similar amounts of flour. Wheat flour contained 1.5% more crude protein, 1.6× more gluten, and produced stronger dough than triticale. Triticale flour significantly reduced optimum water absorption and mix time of blends. Flour tortillas with 100% triticale absorbed 8% less water and required 25% of the mix time of the control wheat flour tortilla. The yield of triticale tortillas was lower than the rest of the tortillas due to lower moisture content and water absorption. Triticale dough balls required less proofing and ruptured during hot pressing, thus producing defective tortillas. The 50:50 flour mixture produced doughs with acceptable rheological properties and good quality tortillas. Addition of 1% vital gluten to the 75:25 triticale‐wheat flour mix or 2% to the 100% triticale flour significantly increased water absorption and mix time and improved dough properties and tortilla yields. Textural studies indicated that increasing levels of triticale flour reduced the force required to rupture tortillas. For all tortilla systems, rupture force gradually increased, and extensibility decreased during seven days of storage at room temperature; the highest rate of change occurred during the first day. Sensory evaluation tests indicated that triticale could substitute for 50% of wheat flour without affecting texture, color, flavor, and overall acceptability of tortillas. For production of 100% triticale flour tortillas, at least 2% vital gluten had to be added to the formulation.     

The Effects of Fresh Eggs,Egg White,and Egg Yolk,Separately and in Combination with Salt,on Mixogram Properties

Salt and eggs are common ingredients in some wheat flour‐based food systems and significantly impact dough mixing behavior. We evaluated the effect of either whole eggs, egg white, or egg yolk on dough formation and properties with the Mixograph. Inclusion of whole eggs in wheat flour dough recipes increased dough development time, dough stability, and dough strength upon further mixing less than inclusion of only egg white. In contrast, egg yolk addition decreased all of these parameters. Salt had a more pronounced impact on dough containing egg yolk than on dough containing egg white. The present observations can be explained in terms of shielding charges of the gluten protein's ionized groups, which largely affects dough mixing behavior. The work demonstrates that in some applications it can be useful to use egg fractions rather than whole eggs.     

Impact of Puroindolines on Semisweet Biscuit Quality: A Fractionation–Reconstitution Approach

Puroindoline (PIN) proteins are a factor determining wheat kernel endosperm texture. Biscuits are preferably made from flour from soft wheat (Triticum aestivum L.). Such wheat contains relatively high levels of wild‐type PINs, the impact of which on biscuit quality is unclear. We here studied the impact of PINs on biscuit texture using model flour samples reconstituted from starch and gluten fractions with varying PIN levels. These were obtained by fractionating flour from soft or durum wheat containing either wild‐type or no PINs, respectively. This approach allowed largely retaining the interaction between PINs and either starch or gluten, such as it exists in flour. High PIN levels enhanced air incorporation during dough preparation, increased dough (lateral) expansion, and yielded larger biscuits with higher porosity, which was mainly because of the larger pores. Biscuit fracture stress negatively correlated with PIN level. Porosity contributed to biscuit mechanical properties, but PINs also affected biscuit matrix strength, which in turn affected fracture stress. PINs seem to exert their softening effect when present above a threshold level, and then they have a stronger impact on biscuit fracture stress than the wheat endogenous lipids.     

Effect of Enzymatic Tempering of Wheat Kernels on Milling and Baking Performance

This study examined the effect of cell‐wall‐degrading enzymes added to temper water on wheat milling performance and flour quality. An enzyme cocktail consisting of cellulase, xylanase, and pectinase and five independent variables (enzyme concentration, incubation time, incubation temperature, tempered wheat moisture content, and tempering water pH) were manipulated in a response surface methodology (RSM) central composite design. A single pure cultivar of hard red winter wheat was tempered under defined conditions and milled on a Ross experimental laboratory mill. Some treatment combinations affected flour yield from the break rolls more than that from the reduction rolls. However, a maximum for flour yield was not found in the range of parameters studied. Though treatments did not affect the optimum water absorption for breadmaking, enzyme‐treated flours produced dough exhibiting shorter mixing times and slack and sticky textures compared with the control. Regardless of differences in mixing times, specific loaf volumes were not significantly different among treatments. Crumb firmness of bread baked with flour milled from enzyme‐treated wheat was comparable to the control after 1 day but became firmer during storage up to 5 days.     

Predicting Wheat Quality Characteristics and Functionality Using Near‐Infrared Spectroscopy

The accuracy of using near‐infrared spectroscopy (NIRS) for predicting 186 grain, milling, flour, dough, and breadmaking quality parameters of 100 hard red winter (HRW) and 98 hard red spring (HRS) wheat and flour samples was evaluated. NIRS shows the potential for predicting protein content, moisture content, and flour color b* values with accuracies suitable for process control (R² > 0.97). Many other parameters were predicted with accuracies suitable for rough screening including test weight, average single kernel diameter and moisture content, SDS sedimentation volume, color a* values, total gluten content, mixograph, farinograph, and alveograph parameters, loaf volume, specific loaf volume, baking water absorption and mix time, gliadin and glutenin content, flour particle size, and the percentage of dark hard and vitreous kernels. Similar results were seen when analyzing data from either HRW or HRS wheat, and when predicting quality using spectra from either grain or flour. However, many attributes were correlated to protein content and this relationship influenced classification accuracies. When the influence of protein content was removed from the analyses, the only factors that could be predicted by NIRS with R² > 0.70 were moisture content, test weight, flour color, free lipids, flour particle size, and the percentage of dark hard and vitreous kernels. Thus, NIRS can be used to predict many grain quality and functionality traits, but mainly because of the high correlations of these traits to protein content.     

Correlation of Quality Parameters with the Baking Performance of Wheat Flours

The baking performance of a set of flours from 13 wheat cultivars was determined by means of two different microscale baking tests (10 g of flour each). In the micro‐rapid‐mix test the dough was mixed for a fixed time at a high speed, whereas the microbaking test used mixing to optimum dough consistency in a microfarinograph. Quality parameters such as sedimentation value, crude protein content, dough and gluten extension data, and microfarinograph data were also determined. Finally, quality‐related protein fractions (gliadins, glutenins, SDS‐soluble proteins, and glutenin macropolymer) were quantitated by extraction/HPLC methods with reversed‐phase and gel‐permeation columns. All quality parameters were correlated with the bread volumes of both baking tests. The results demonstrated that the microbaking test (adapted mixing time) was much more closely related to the quality parameters than the micro‐rapid‐mix test (fixed mixing time), which hardly showed any correlation. Among the standard quality parameters, only the crude protein content showed a medium correlation with the bread volume of the microbaking test (r = 0.71), whereas the contents of gliadins (r = 0.80), glutenins (r = 0.76), and glutenin macropolymer (r = 0.80) appeared to be suitable parameters to predict the baking performance of wheat flour. All other quality parameters were not or were only weakly correlated and unsuitable for predicting baking performance.     

基于低场核磁和差示量热扫描的面条面团水分状态研究

为了解低水分面条面团中水分的存在状态,明确真空度及和面时间对水分状态的影响,该研究以3个小麦品种（济麦20、宁春4号、济麦22）磨制的面粉为材料,采用真空和面制作低水分面条面团（含水率35%）,采用低场核磁共振技术（LF-NMR,low-field nuclear magnetic resonance）和差示量热扫描（DSC,differential scanning calorimetry）2种技术,测定不同真空度（0、0.06、0.09 MPa）和搅拌时间（4、8、12 min）下面团中水分的形态和分布,并进一步分析2种技术测定水分形态结果的相关性。结果表明,在低水分面条面团中,水分主要以弱结合水形态存在。不同品种的小麦粉面团的水分形态及分布存在差异,强筋小麦粉（济麦20）制作面团的水分自由度较低。真空和面（0.06 MPa）可以促进水分与面筋蛋白的相互作用,降低面团中水分子流动性,促进水分结构化;而非真空或过高真空度均会导致面团中水分自由度增加。济麦20、济麦22小麦粉和面时间为8 min时,面团水分流动性较低;而宁春4号小麦粉面团在4 min时,水分自由度较低;继续搅拌,深层结合水减少、弱结合水增多。LF-NMR和DSC测得面团水分状态的结果具有一致性。LF-NMR测得的弱结合水峰面积百分比与DSC测得的可冻结水百分比具有相同的变化趋势（r=0.695）,且深层结合水峰面积百分比与非冻结水百分比具有相同的变化趋势（r=0.564）。研究结果为认识制面过程中水分的作用,优化和面工艺和调整产品特性提供参考。     

Association of Glutenin Subunit Composition and Dough Rheological Characteristics with Cookie Baking Properties of Soft Wheat Cultivars

The effect of flour type and dough rheology on cookie development during baking was investigated using seven different soft winter wheat cultivars. Electrophoresis was used to determine the hydrolyzing effects of a commercial protease enzyme on gluten protein and to evaluate the relationships between protein composition and baking characteristics. The SDS‐PAGE technique differentiated flour cultivars based on the glutenin subunits pattern. Electrophoresis result showed that the protease degraded the glutenin subunits of flour gluten. Extensional viscosities of cookie dough at all three crosshead speeds were able to discriminate flour cultivar and correlated strongly and negatively to baking performance (P < 0.0001). The cookie doughs exhibited extensional strain hardening behavior and those values significantly correlated to baking characteristics. Of all rheological measurements calculated, dough consistency index exhibited the strongest correlation coefficient with baking parameters. The degradation effects of the protease enzyme resulted in more pronounced improvements on baking characteristics compared with dough rheological properties. Stepwise multiple regression showed that the dough consistency index, the presence or absence of the fourth (44 kDa) subunit in LMW‐GS and the fifth subunit (71 kDa) subunit in HMW‐GS were predominant parameters in predicting cookie baking properties.     

Baking Performance of Durum and Soft Wheat Flour in a Sponge-Dough Breadmaking Procedure

Breadmaking properties were determined for formulations that included durum, soft, and spring wheat flour, using a pound-loaf sponge-dough baking procedure. Up to 60% durum or soft wheat flour plus 10% spring wheat flour could be incorporated at the sponge stage for optimum dough-handling properties. At remix, the dough stage required 30% spring wheat flour. Bread made with 100% spring wheat flour was used as a standard for comparison. Bread made with 60% durum flour exhibited internal crumb color that was slightly yellow. When storing pound bread loaves for 72 hr, crumb moisture content remained unchanged. Crumb firmness and enthalpy increased the most in bread made with 60% soft wheat flour. Crumb firmness increased the least in bread made with 100% spring wheat flour. Enthalpy changed the least in bread made with 60% durum flour. Crumb moisture content was significantly correlated with crumb firmness (r = -0.82) and enthalpy (r = -0.65). However, crumb moisture content was specific for each type of flour and a function of flour water absorption; therefore, these correlations should be interpreted with caution. Crumb firmness and enthalpy were significantly correlated (r = 0.65). Ball-milling flour resulted in an increase in water absorption of ≈2% and in crumb moisture content of ≈0.5% but had no effect on either crumb firmness or enthalpy.     

Effects of Transglutaminase Enzyme on Fundamental Rheological Properties of Sound and Bug‐Damaged Wheat Flour Doughs

Transglutaminase (TG) catalyzes the formation of nondisulfide covalent crosslinks between peptide‐bound glutaminyl residues and ∊‐amino groups of lysine residues in proteins. Crosslinks among wheat gluten proteins by TG are of particular interest because of their high glutamine content. Depolymerization of wheat gluten proteins by proteolytic enzymes associated with bug damage causes rapid deterioration of dough properties and bread quality. The aim of the present study was to investigate the possibility of using TG to regain gluten strength adversely affected by wheat bug proteases. A heavily bug‐damaged (Eurygaster spp.) wheat flour was blended with sound cv. Augusta or cv. Sharpshooter flours. Dynamic rheological measurements, involving a frequency sweep at a fixed shear stress, were performed after 0, 30, and 60 min of incubation on doughs made from sound or blended flour samples. The complex moduli (G* values) of Augusta and Sharpshooter doughs blended with 10% bug‐damaged flour decreased significantly after 30 min of incubation. These dough samples were extremely soft and sticky and impossible to handle for testing purposes after 60 min of incubation. To test the possibility of using TG to counteract the hydrolyzing effect of bug proteases on gluten proteins, TG was added to the flour blends. The G* values of TG‐treated sound Augusta or Sharpshooter doughs increased significantly after 60 min of incubation. The G* values of the Augusta or Sharpshooter doughs blended with bug‐damaged flour increased significantly rather than decreased after 30 and 60 min of incubation when TG was included in the dough formulation. This indicates that the TG enzyme substantially rebuilds structure of dough hydrolyzed by wheat bug protease enzymes.     

Whole Grain Wheat Flour Production Using an Ultracentrifugal Mill

Interest has been growing in whole grain products. However, information regarding the influence of the ultracentrifugal mill on whole grain flour quality has been limited. An experiment was conducted to produce whole wheat flour with hard red spring (HRS) wheat using an ultracentrifugal mill. This study determined the effect of centrifugal mill parameters as well as grain moisture (10–16%) on producing whole wheat flour and its final products. Mill parameters studied were rotor speed (6,000–15,000 rpm) and feed rate (12.5–44.5 g/min). Results showed that fine particle size (<150 µm) was favored by low seed moisture content (10–12%) and high rotor speed (12,000–15,000 rpm). Flour moisture content was positively related to seed moisture content. Wheat grain with low seed moisture content (10–12%) milled with high rotor speeds (12,000–15,000 rpm) produced desirable whole grain wheat flour quality, with 70–90% of fine particle size portion and low damaged starch (less than 11%). This whole wheat flour produced uniform and machinable dough that had low stickiness and formed bread with high loaf volume.     

Structural Modifications of Gluten Proteins in Strong and Weak Wheat Dough During Mixing

The network‐forming attributes of gluten have been investigated for decades, but no study has comprehensively addressed the differences in gluten network evolution between strong and weak wheat types (hard and soft wheat). This study monitored changes in SDS protein extractability, SDS‐accessible thiols, protein surface hydrophobicity, molecular weight distribution, and secondary structural features of proteins during mixing to bring out the molecular determinants of protein network formation in hard and soft wheat dough. Soft wheat flour and dough exhibited greater protein extractability and more accessible thiols than hard wheat flour and dough. The addition of the thiol‐blocking agent N‐ethylmaleimide (NEM) resulted in similar results for protein extractability and accessible thiols in hard and soft wheat samples. Soft wheat dough had greater protein surface hydrophobicity than hard wheat and exhibited a larger decrease in surface hydrophobicity in the presence of NEM. Formation of high‐molecular‐weight (HMW) protein in soft wheat dough was primarily because of formation of disulfides among low‐molecular‐weight (LMW) proteins, as indicated by the absence of changes in protein distribution when NEM was present, whereas in hard wheat dough the LMW fraction formed disulfide interaction with the HMW fraction. Fourier transform infrared spectroscopy indicated formation of β‐sheets in dough from either wheat type at peak mixing torque. Formation of β‐sheets in soft wheat dough appears to be driven by hydrophobic interactions, whereas disulfide linkages stabilize secondary structure elements in hard wheat dough.     

Retrogradation of Rice Flour Gel and Dough: Plasticization Effects of Some Food Additives

Certain food additives commonly used in flour products also have a plasticization effect on product shelf life regarding retrogradation. Sucrose, sorbitol, glycerol, citric acid, and acetic acid at 25, 25, 25, 0.5, and 0.5%, respectively, were added to two different starch gel systems: slurry (high‐amylose rice flour gel) and dough (waxy rice flour dough). All plasticizers increased gelatinization temperature, decreased enthalpy (ΔH), and promoted a more homogeneous system. Sucrose had the greatest effect on gelatinization increase. Rice dough was more susceptible to plasticizers, resulting in higher moisture content and a more amorphous structure. Retrogradation was highly positively correlated with amylose content, moisture retention, ratio of protons of water/starch, and previous occurrence of retrogradation. Moisture retention was increased in plasticizer‐added samples, especially waxy rice dough. Over a longer storage period, sucrose and sorbitol showed an antiplasticization effect in waxy rice flour dough, but glycerol and acid caused higher retrogradation in high‐amylose rice flour gel.     

Wheat Tortilla Quality: Impact of Amylose Content Adjustments Using Waxy Wheat Flour

Amylose content is closely related to wheat flour pasting or thermal properties, and thus affects final food qualities. Fourteen flour blends with amylose content ranges of <1 to 29% were used to study tortilla production and quality parameters. Reduced amylose contents decreased dough stickiness and pliability; low amylose doughs were also very smooth in appearance. Very low flour amylose content was associated with earlier tortilla puffing and poor machinability during baking, darker color, low opacity, larger diameters, and reduced flexibility after storage. Tortilla texture analysis indicated that lowering amylose content gave fresh tortillas higher extensibility; after three or more days storage, however, low amylose flours required more force to break the tortillas and the rupture distances became shorter. These results, as reflected in covariate analysis, were not significantly affected by the flour blend's protein content, swelling volume/power, SDS‐sedimentation volume, mixograph dough development time, or mixograph tolerance score. Based on our observation of an initial increase in extensibility with reduced‐amylose tortillas, adding 10–20% waxy flour into wild‐type flours should be ideal for restaurant (on‐site) tortilla production or circumstances where tortillas are consumed shortly (within a day) after production. The optimal flour amylose content for hot‐press wheat tortilla products is 24–26%.     

Gliadin Immunoreactivity and Dough Rheological Properties of Winter Wheat Genotypes Modified by Thioredoxin

Gliadins are among the most important protein fractions affecting wheat baking quality, but they are also plant allergens and a cause of celiac disease or food intolerance. Therefore, we investigated how gliadin immunoreactivity and dough rheological properties are influenced by thioredoxin, a regulatory disulfide protein that can reduce disulfide bonds, a typical motive in many allergenic proteins. Ten winter wheat genotypes of different qualities were analyzed. Reduction by thioredoxin strongly (>50%) decreased gliadin immunoreactivity as estimated by enzyme‐linked immunosorbent assay with immunoglobulin E (IgE) sera from allergic patients and standard antigliadin antibodies but did not significantly affect dough rheological properties. Most parameters from the Brabender extensigraph were only slightly lower. Simultaneously, the farinograph curve exhibited a drawdown dislocation, possibly due to increased water absorption by modified flour, and dough consistency visibly improved. Results suggest that thioredoxin may be a universal natural beneficial modifier, able to significantly decrease gliadin immunoreactivity (hence its potential allergenicity) without decreasing the unique technological properties of wheat flour.     

Effects of Nitrogen and Sulfur Fertilizer on Protein Composition,Mixing Requirements,and Dough Strength of Four Wheat Cultivars

Two field trials using four New Zealand wheat cultivars were undertaken to observe the effects of nitrogen and sulfur fertilization on protein composition, mixing requirements, and dough strength and to compare the results with that observed with a single cultivar, Otane. The results confirmed that adequate sulfur fertilization was necessary to ensure lower dough mixing requirements. The existence of a nexus between mixing requirements and dough strength was confirmed and genotype has significant effects on it. Variation in the content of HMW‐GS in the protein corresponded to changes in dough mixing requirement of Otane. Across the four cultivars, dough mixing requirements (mechanical dough development work input and mixograph development time) and dough strength (Extensigraph resistance to extension) depended on different aspects of protein composition. As the content of polymeric proteins increased, MDD work input increased, but mixograph development time decreased, while the effect on Rmax was small. Rmax, however, was more affected by either the content of small monomerics in the flour or the ratio between HMW‐GS peak area to total gliadin peak area. The ratio of MDD work input to Rmax was largely explained by the gliadin content of the flour. Thus, depending on the genetic background, it should be possible to adjust dough mixing requirements by modifying overall HMW‐GS, LMW‐GS, or gliadin content while maintaining dough strength.     

Effects of Micronization on Protein and Rheological Properties of Spring Wheat

This research investigated the effects of micronization, at different moisture levels, on the chemical and rheological properties of wheat. A set of tests designed to analyze protein fraction characteristics and rheological behaviors were conducted on samples from four wheat cultivars (AC Karma, AC Barrie, Glenlea, and Kanata). After being subjected to infrared radiation at three moisture levels (as‐is, 16%, and 22%), the seeds were milled to produce straight‐grade flour. The protein fractionation test revealed significant decreases (P ≤ 0.01) in both monomeric proteins (from 54% of total protein in the control to 37% in the tempered micronized sample) and soluble glutenins (9.4–2.5%). There was a strong negative correlation (r = ‐0.98) between the percentages of monomeric proteins and insoluble glutenins. Total extractable proteins of micronized samples tempered to 22% moisture decreased 43.5% when compared with nonmicronized control samples using size‐exclusion HPLC (SE‐HPLC). Micronization had a significant effect on gluten properties, as seen from a decrease in water absorption (P ≤ 0.01) and dough development time (P ≤ 0.01). Results showed that micronization at 100 ± 5°C had detrimental effects on wheat flour gluten functionality, including a decrease in protein solubility and impairment of rheological properties. These phenomena could be due to the formation of both hydrophobic and disulfide bonds in wheat during micronization.