Quality of Flours from Waxy and Nonwaxy Barley for Production of Baked Products

One nonwaxy (covered) and two waxy (hull-less) barleys, whole grain and commercially abraded, were milled to break flour, reduction flour, and the bran fraction with a roller mill under optimized conditions. The flour yield range was 55.3–61.8% in whole grain and increased by 9–11% by abrasion before milling. Break flours contained the highest starch content (≤85.8%) independent of type of barley and abrasion level. Reduction flours contained less starch, but more protein, ash, free lipids, and total β-glucans than break flours. The bran fraction contained the highest content of ash, free lipids, protein, and total β-glucans but the lowest content of starch. Break flours milled from whole grain contained 82–91% particles <106 μm, and reduction flours contained ≈80% particles <106 μm. Abrasion significantly increased the amount of particles <38 μm in break and reduction flours in both types of barley. Viscosity of hot paste prepared with barley flour or bran at 8% concentration was strongly affected by barley type and abrasion level. In cv. Waxbar, the viscosity in bran fractions increased from 428 to 1,770 BU, and in break flours viscosity increased from 408 to 725 BU due to abrasion. Sugar snap cookies made from nonwaxy barley had larger diameter than cookies prepared from waxy barley. Cookies made from break flours were larger than those made from reduction flours, independent of type of barley. Quick bread baked from nonwaxy barley had a loaf volume similar to that of wheat bread, whereas waxy barley bread had a smaller loaf volume. Replacement of 20% of wheat flour by both waxy and nonwaxy barley flour or bran did not significantly affect the loaf volume but did decrease the hardness of quick bread crumb.     

Factors Controlling Gas Cell Failure in Bread Dough

Stress relaxation in the wall of a gas bubble, as measured by the alveograph, was used to study surface tension at the gas-dough interface of doughs from flours producing differing bread crumb grains. The surface tensions in the various wheat flour doughs were not different. Dough rheological properties, as measured by both dynamic oscillatory rheometry and lubricated uniaxial compression, were not different for doughs made from wheat flours that gave breads with different crumb grains. However, when the effect of starch granule size on gas cell wall stability was tested, the presence of a greater proportion of large starch granules in wheat flour dough was sufficient to result in gas cell coalescence and open crumb grain in the final baked product. This suggests that starch granule size is at least one of the factors that affects the crumb grain of bread.     

Wheat Tortilla Quality: Impact of Amylose Content Adjustments Using Waxy Wheat Flour

Amylose content is closely related to wheat flour pasting or thermal properties, and thus affects final food qualities. Fourteen flour blends with amylose content ranges of <1 to 29% were used to study tortilla production and quality parameters. Reduced amylose contents decreased dough stickiness and pliability; low amylose doughs were also very smooth in appearance. Very low flour amylose content was associated with earlier tortilla puffing and poor machinability during baking, darker color, low opacity, larger diameters, and reduced flexibility after storage. Tortilla texture analysis indicated that lowering amylose content gave fresh tortillas higher extensibility; after three or more days storage, however, low amylose flours required more force to break the tortillas and the rupture distances became shorter. These results, as reflected in covariate analysis, were not significantly affected by the flour blend's protein content, swelling volume/power, SDS‐sedimentation volume, mixograph dough development time, or mixograph tolerance score. Based on our observation of an initial increase in extensibility with reduced‐amylose tortillas, adding 10–20% waxy flour into wild‐type flours should be ideal for restaurant (on‐site) tortilla production or circumstances where tortillas are consumed shortly (within a day) after production. The optimal flour amylose content for hot‐press wheat tortilla products is 24–26%.     

Quality Characteristics of Yellow Alkaline Noodles Enriched with Hull‐less Barley Flour

Roller milled flours from eight genotypes of hull‐less barley (HB) with normal, waxy, zero amylose waxy (ZAW), and high amylose (HA) starch were incorporated at 20 and 40% (w/w) with a 60% extraction Canada Prairie Spring White (CPSW, cv. AC Vista) wheat flour to evaluate their suitability as a blend for yellow alkaline noodles (YAN). The barley flour supplemented noodles were prepared using conventional equipment. Noodles containing 40% HB flour required less work input than the corresponding 20% blend noodles due to a higher water absorption at the elevated level of HB flour addition, which probably caused them to soften. The addition of any HB flour at either level to the CPSW flour resulted in significantly decreased brightness (L*) and yellowness (b*), elevated redness (a*), concomitant with a significantly greater number of specks per unit area of noodle sheet compared with the control flour. The addition of 40% HB flour to YAN decreased cook time and cooking losses. Noodle firmness, as determined by maximum cutting stress (MCS), was significantly increased by the addition of 40% HB flour. Noodle chewiness, as determined by the texture profile analysis (TPA), was affected by the type of starch in the barley samples; the addition of waxy and ZAW HB flour decreased chewiness, whereas normal and HA HB flour increased chewiness of composite noodles.     

Quality Characteristics of Fresh and Dried White Salted Noodles Enriched with Flour from Hull‐less Barley Genotypes of Diverse Amylose Content

Fresh and dried white salted noodles (WSN) were prepared by incorporating up to 40% flour from hull‐less barley (HB) genotypes with normal amylose, waxy, zero amylose waxy (ZAW), and high amylose (HA) starch into a 60% extraction Canada Prairie Spring White (cv. AC Vista) wheat flour. The HB flours, depending on genotype, contained four to six times the concentration of β‐glucan of the wheat flour, offering potential health benefits. The HB‐enriched noodles were made with conventional equipment without difficulty. Noodles containing 40% HB flour required less work input during sheeting, probably due to higher optimum water absorption and weakening of the dough due to dilution of wheat gluten. The addition of HB flour had a negative impact on WSN color and appearance, as evident from decreased brightness, increased redness, and more visible specking. The impact of HB flour on cooked WSN texture varied by starch type. Enrichment with HA or normal starch HB flour produced WSN with bite and chewiness values equivalent to or superior to the wheat flour control. Addition of waxy and ZAW HB flour resulted in WSN with lower values for bite and chewiness. The diversity of HB starch types allows tailoring of WSN texture to satisfy specific markets. HB flour also has potential as an ingredient in novel noodle products targeting health‐conscious consumers who associate darker colored cereal‐based foods with superior nutritional composition.     

Effect of Damaged Starch and NaCl Level on the Dough Handling Properties of a Canadian Western Red Spring Wheat

The effects of damaged starch and NaCl (1 and 2% w/w [flour weight]) on the dough handling properties of a wheat flour (Triticum asetivum L. ‘Roblin’) were investigated with rheological and textural methods. Damaged starch levels of the base flour and three remilled flours (using reduction rolls with decreasing gap sizes) were 5.42, 6.23, 7.30, and 8.43%. Rheological measurements on the dough showed that the complex modulus increased and the loss tangent (tan δ) decreased with increasing damaged starch levels in the flour, indicating that greater amounts of damaged starch produced stiffer dough. The base flour produced doughs with the highest creep compliance value (J _max), whereas the flour with the most damaged starch deformed the least. Higher levels of salt produced stiffer dough that deformed less, as evident by the higher complex modulus and lower creep compliance, compared with 1% NaCl. Damaged starch overall decreased dough stickiness (N), work of adhesion (N·s), and cohesiveness (mm). Increasing the salt content decreased the stickiness of the doughs. Increasing the damaged starch greatly increased dough extensibility at 1% NaCl. The greater amounts of damaged starch in the remilled flour mitigated some of the negative effects of reducing the salt content on the dough machinability.     

Effects of Oat Grain Hydrothermal Treatments on Wheat-Oat Flour Dough Properties and Breadbaking Quality

Hydrothermal treatments, which are routine in oat processing, have profound effects on oat flour dough rheological properties. The influence of roasting and steam treatments of oat grain on dough mixing and breadbaking properties was investigated when hydrothermally treated oat flour was blended with wheat flour. Roasting of oat grain (105°C, 2 hr) resulted in oat flours that were highly detrimental to wheat flour dough mixing properties and breadbaking quality. Steaming (105°C, 20 min) or a combination of roasting and steaming of oat grain significantly improved the breadbaking potential of the oat flours. The addition of oat flours increased water absorption and mixing requirements of the wheat flour dough and also decreased bread loaf volume. However, at the 10% substitution level, steamed oat flours exhibited only a gluten dilution effect on bread loaf volume when wheat starch was used as a reference. Oat flour in the breadbaking system decreased the retrogradation rate of bread crumb starch. The results indicate that adequate hydrothermal treatments of oat grain are necessary for oat flour breadbaking applications. Steamed oat flours used at a 10% level retarded bread staling without adversely affecting the loaf volume.     

Significance of Amylose Content of Wheat Starch on Processing and Textural Properties of Instant Noodles

The effect of amylose content of starch on processing and textural properties of instant noodles was determined using waxy, partial waxy, and regular wheat flours and reconstituted flours with starches of various amylose content (3.0–26.5). Optimum water absorption of instant noodle dough increased with the decrease of amylose content. Instant noodles prepared from waxy and reconstituted wheat flours with ≤12.4% amylose content exhibited thicker strands and higher free lipids content than wheat flours with ≥17.1% amylose content. Instant noodles of ≤12.4% amylose content of starch exhibited numerous bubbles on the surface and stuck together during frying. Lightness of instant noodles increased from 77.3 to 81.4 with the increase of amylose content of starch in reconstituted flours. Cooking time of instant noodles was 4.0–8.0 min in wheat flours and 6.0–12.0 min in reconstituted flours, and constantly increased with the increase in amylose content of starch. Hardness of cooked instant noodles positively correlated with amylose content of starch. Reconstituted flours with ≤12.4% amylose content of starch were higher in cohesiveness than those of wheat flours of wild‐type and partial waxy starches and reconstituted flours with ≥17.1% amylose content. Instant fried noodles prepared from double null partial waxy wheat flour exhibited shorter cooking time, softer texture, and higher fat absorption (1.2%) but similar color and appearance compared with noodles prepared from wheat flour of wild‐type starch.     

Characteristics of French Bread Baked from Wheat Flours of Reduced Starch Amylose Content

Wheat genotypes of wild type, partial waxy, and waxy starch were used to determine the influence of starch amylose content on French bread making quality of wheat flour. Starch amylose content and protein content of flours were 25.0–25.4% and 14.3–16.9% for wild type; 21.2 and 14.9% for single null partial waxy; 15.4–17.1% and 13.2–17.6% for double null partial waxy; and 1.8 and 19.3% for waxy starch, respectively. Wheat flours of double null partial waxy starch produced smaller or comparable loaf volume of bread than wheat flours of wild type and single null partial waxy starch. Waxy wheat flour, despite its high protein content, generally produced smaller volume of bread with highly porous, glutinous, and weak crumb than wheat flours of wild type and partial waxy starch. French bread baked from a flour of double null partial waxy starch using the sponge-and-dough method maintained greater crumb moisture content for 24 hr and softer crumb texture for 48 hr of storage compared with bread baked from a flour of wild type starch. In French bread baked using the straight-dough method, double null partial waxy wheat flours with protein content >14.3% exhibited comparable or greater moisture content of bread crumb during 48 hr of storage than wheat flours of wild type starch. While the crumb firmness of bread stored for 48 hr was >11.4 N in wheat flours of wild type starch, it was <10.6 N in single or double null partial waxy flours. Wheat flours of reduced starch amylose content could be desirable for production of French bread with better retained crumb moisture and softness during storage.     

Influence of Added Starch on Mixing of Dough Made with Three Wheat Flours Differing in High Molecular Weight Subunit Composition: Rheological Behavior

The effect of mixing time (6 and 20 min) and starch content were studied on doughs prepared with three wheat flours differing in high molecular weight subunit composition. Rheological measurements were performed in dynamic oscillation: frequency and strain sweeps, stress relaxation, and in large deformation viscosity measurements. The flours were diluted with starch to cover flour protein contents of 10–15%. Water was added to keep the starch‐water ratio constant when doughs were prepared with different protein contents. By increasing the starch content of the doughs, the rheological properties approached those of a starch‐water mixture prepared with the same starch‐water ratio as in the dough. The effect of the starch granules was reinforced by prolonged mixing. This may explain the higher values of the storage modulus and relaxation times observed after 20 min of mixing. Qualities related to gluten properties, appeared more clearly in large deformation viscosity measurements.     

Significance of Starch Properties and Quantity on Sponge Cake Volume

We evaluated the qualitative and quantitative effects of wheat starch on sponge cake (SC) baking quality. Twenty wheat flours, including soft white and club wheat of normal, partial waxy, and waxy endosperm, as well as hard wheat, were tested for amylose content, pasting properties, and SC baking quality. Starches isolated from wheat flours of normal, single‐null partial waxy, double‐null partial waxy, and waxy endosperm were also tested for pasting properties and baked into SC. Double‐null partial waxy and waxy wheat flours produced SC with volume of 828–895 mL, whereas volume of SC baked from normal and single‐null partial waxy wheat flours ranged from 1,093 to 1,335 mL. The amylose content of soft white and club wheat flour was positively related to the volume of SC (r = 0.790, P < 0.001). Pasting temperature, peak viscosity, final viscosity, breakdown, and setback also showed significant relationships with SC volume. Normal and waxy starch blends having amylose contents of 25, 20, 15, and 10% produced SCs with volume of 1,570, 1,435, 1,385, and 1,185 mL, respectively. At least 70 g of starch or at least 75% starch in 100 g of starch–gluten blend in replacement of 100 g of wheat flour in the SC baking formula was needed to produce SC having the maximum volume potential. Starch properties including amylose content and pasting properties as well as proportion of starch evidently play significant roles in SC baking quality of wheat flour.     

Dough and Baking Properties of High‐Amylose and Waxy Wheat Flours

The dough properties and baking qualities of a novel high‐amylose wheat flour (HAWF) and a waxy wheat flour (WWF) (both Triticum aestivum L.) were investigated by comparing them with common wheat flours. HAWF and WWF had more dietary fiber than Chinese Spring flour (CSF), a nonwaxy wheat flour. Also, HAWF contained larger amounts of lipids and proteins than WWF and CSF. There were significant differences in the amylose and amylopectin contents among all samples tested. Farinograph data showed water absorptions of HAWF and WWF were significantly higher than that of CSF, and both flours showed poorer flour qualities than CSF. The dough of WWF was weaker and less stable than that of CSF, whereas HAWF produced a harder and more viscous dough than CSF. Differential scanning calorimetry data showed that starch in HAWF dough gelatinized at a lower temperature in the baking process than the starches in doughs of WWF and CSF. The starch in a WWF suspension had a larger enthalpy of gelatinization than those in HAWF and CSF suspensions. Amylograph data showed that the WWF starch gelatinized faster and had a higher viscosity than that in CSF. The loaves made from WWF and CSF were significantly larger than the loaves made from HAWF. However, the appearance of bread baked with WWF and HAWF was inferior to the appearance of bread baked with CSF. Bread made with WWF became softer than the bread made with CSF after storage, and reheating was more effective in refreshing WWF bread than CSF bread. Moreover, clear differences in dough and bread samples were revealed by scanning electron microscopy. These differences might have some effect on dough and baking qualities.     

Effect of Puroindolines on the Breadmaking Properties of Wheat Flour

The role of lipid-binding proteins from wheat seed (puroindolines) on the breadmaking properties of wheat flour was investigated by determining the relationship between breadmaking quality and puroindoline content in samples of 32 wheat cultivars. An inverse relationship was mainly explained by the link between hardness and puroindoline contents. This link is in agreement with previous results which have shown a close structural identity between basic friabilins and puroindolines. Next, the effect of puroindolines in breadmaking was investigated by performing reconstitution experiments with two puroindoline-free hard cultivars of opposite quality (Florence Aurore and Ecrin) as indicated in the screened wheat sample. Addition of 0.1% puroindolines to these flours drastically modified both the rheological properties of doughs and the structure of the bread crumb. Puroindolines are essential to the foaming properties of dough liquor, and a close relationship was found between the fine grain crumb provided by reconstituted flours with puroindolines and the fine structure of corresponding dough liquor foams. The effect of puroindolines on bread volume was mainly related to the rheological properties of wheat doughs.     

Influence of Starch and Gluten Characteristics on Rheological Properties of Wheat Flour Gel at Small and Large Deformation

Starch and gluten were isolated from 10 wheat cultivars or lines with varied amylose content. The rheological properties of 30% wheat flour gel, starch gel, and the gel of isolated gluten mixed with common starch were determined in dynamic mechanical testing under shear deformation, creep‐recovery, and compression tests under uniaxial compression. Variation of wheat samples measured as storage shear modulus (G′), loss shear modulus (G″), and loss tangent (tan δ = G″/G′) was similar between flour and starch gels and correlated significantly between flour and starch gel. The proportion of acetic acid soluble glutenin exhibited a significant relationship with tan δ of gluten‐starch mixture gel. The small difference in amylose content strongly affected the rheological parameters of flour gels in creep‐recovery measurement. Wheat flour gel with lower amylose content showed higher creep and recovery compliance that corresponded to the trend in starch gel. Compressive force of flour gel at 50 and 95% strain correlated significantly with that of starch gel. Gel mixed with the isolated gluten from waxy wheat lines appeared to have a weaker gel structure in dynamic viscoelasticity, creep‐recovery, and compression tests. Starch properties of were primarily responsible for rheological changes in wheat flour gel.     

Dough Properties and Bread Quality of Wheat–Barley Composite Flour as Affected by β‐Glucanase

Barley is rich in nutritionally positive compounds, but the quality of bread made of wheat–barley composite flours is impaired when a high percentage of barley is used in the mixture. A number of enzymes have been reported to be useful additives in breadmaking. However, the effect of β‐glucanase on breadmaking has scarcely been investigated. In this paper, the influence of different levels (0.02, 0.04, 0.06, and 0.08%, based on composite flour) of β‐glucanase (100,000 U/g) on the properties of dough and bread from 70% wheat, 30% barley composite flour were studied. Although dough development time, dough stability, and protein weakening value decreased after β‐glucanase addition, dough properties such as softness and elasticity as well as bread microstructure were improved compared with the control dough. β‐Glucanase also significantly improved the volume, texture, and shelf life of wheat–barley composite breads. The use of an optimal enzyme concentration (0.04%) increased specific volume (57.5%) and springiness (21%), and it reduced crumb firmness (74%) and staling rate. Bread with added β‐glucanase had a better taste, softness, and overall acceptability of sensory characteristics compared with the control bread. Moreover, the quality of wheat–barley composite bread after addition of 0.04% β‐glucanase was nearly equal to the quality of pure wheat bread. These results indicate that dough rheological characteristics and bread quality of wheat–barley composite flour can be improved by adding a distinct level of β‐glucanase.     

Breadmaking Use of Andean Crops Quinoa,Kañiwa,Kiwicha, and Tarwi

The effect of addition of flours from the highly nutritious Andean crops quinoa (Chenopodium quinoa), kañiwa (Chenopodium pallidicaule), kiwicha (Amaranthus caudatus), and tarwi (Lupinus mutabilis) has been investigated in wheat doughs and fresh bread quality. The thermomechanical profile of wheat doughs and bread quality has been explored by increasing substitution of wheat flour at 0–100% by Andean crop flours. Dough blends were evaluated using the Chopin Mixolab device, whereas bread quality assessment comprised sensory (overall acceptability) and physicochemical (moisture, specific volume, texture, color) determinations in composite breads. In general, no breads with aerated crumb structure could be obtained from 100% Andean crop flours, with the exception of quinoa breads that had overall sensory values about half a completely perfect score, and which were not significantly different from the breads made from a 50:50 blend of wheat and quinoa. Replacement of wheat flour by ≤12.5% (tarwi), 25% (kañiwa), and 50% (kiwicha), respectively, still produced breads with good sensory acceptability but variable color and doughs with acceptable thermomechanical patterns. Partial substitution of wheat flour by Andean crop flours constitutes a viable option to improve the nutritional value of the breads, with acceptable technological performance of dough blends and composite breads.     

Characteristics of Noodles and Bread Prepared from Double‐Null Partial Waxy Wheat

Double‐null partial waxy wheat (Triticum aestivum L.) flours were used for isolation of starch and preparation of white salted noodles and pan bread. Starch characteristics, textural properties of cooked noodles, and staling properties of bread during storage were determined and compared with those of wheat flours with regular amylose content. Starches isolated from double‐null partial waxy wheat flours contained 15.4–18.9% amylose and exhibited higher peak viscosity than starches of single‐null partial waxy and regular wheat flours, which contained 22.7–25.8% amylose. Despite higher protein content, double‐null partial waxy wheat flours, produced softer, more cohesive and less adhesive noodles than soft white wheat flours. With incorporation of partial waxy prime starches, noodles produced from reconstituted soft white wheat flours became softer, less adhesive, and more cohesive, indicating that partial waxy starches of low amylose content are responsible for the improvement of cooked white salted noodle texture. Partial waxy wheat flours with >15.1% protein produced bread of larger loaf volume and softer bread crumb even after storage than did the hard red spring wheat flour of 15.3% protein. Regardless of whether malt was used, bread baked from double‐null partial waxy wheat flours exhibited a slower firming rate during storage than bread baked from HRS wheat flour.     

Barley grain constituents, starch composition, and structure affect starch in vitro enzymatic hydrolysis

The relationship between starch physical properties and enzymatic hydrolysis was determined using ten different hulless barley genotypes with variable carbohydrate composition. The ten barley genotypes included one normal starch (CDC McGwire), three increased amylose starches (SH99250, SH99073, and SB94893), and six waxy starches (CDC Alamo, CDC Fibar, CDC Candle, Waxy Betzes, CDC Rattan, and SB94912). Total starch concentration positively influenced thousand grain weight (TGW) (r(2) = 0.70, p < 0.05). Increase in grain protein concentration was not only related to total starch concentration (r(2) = -0.80, p < 0.01) but also affected enzymatic hydrolysis of pure starch (r(2) = -0.67, p < 0.01). However, an increase in amylopectin unit chain length between DP 12-18 (F-II) was detrimental to starch concentration (r(2) = 0.46, p < 0.01). Amylose concentration influenced granule size distribution with increased amylose genotypes showing highly reduced volume percentage of very small C-granules (<5 μm diameter) and significantly increased (r(2) = 0.83, p < 0.01) medium sized B granules (5-15 μm diameter). Amylose affected smaller (F-I) and larger (F-III) amylopectin chains in opposite ways. Increased amylose concentration positively influenced the F-III (DP 19-36) fraction of longer DP amylopectin chains (DP 19-36) which was associated with resistant starch (RS) in meal and pure starch samples. The rate of starch hydrolysis was high in pure starch samples as compared to meal samples. Enzymatic hydrolysis rate both in meal and pure starch samples followed the order waxy > normal > increased amylose. Rapidly digestible starch (RDS) increased with a decrease in amylose concentration. Atomic force microscopy (AFM) analysis revealed a higher polydispersity index of amylose in CDC McGwire and increased amylose genotypes which could contribute to their reduced enzymatic hydrolysis, compared to waxy starch genotypes. Increased β-glucan and dietary fiber concentration also reduced the enzymatic hydrolysis of meal samples. An average linkage cluster analysis dendrogram revealed that variation in amylose concentration significantly (p < 0.01) influenced resistant starch concentration in meal and pure starch samples. RS is also associated with B-type granules (5-15 μm) and the amylopectin F-III (19-36 DP) fraction. In conclusion, the results suggest that barley genotype SH99250 with less decrease in grain weight in comparison to that of other increased amylose genotypes (SH99073 and SH94893) could be a promising genotype to develop cultivars with increased amylose grain starch without compromising grain weight and yield.     

Viscoelastic properties of waxy and nonwaxy rice flours, their fat and protein-free starch, and the microstructure of their cooked kernels

Physicochemistry and structural studies of two types of japonica rice, low amylose Calmochi-101 (CM101) and intermediate amylose M-202 (M202), were conducted to determine similarities and differences between the rices perhaps attributable to amylose content differences. The rheological behavior of the gelation and pasting processes of flours and starches was determined with high accuracy and precision using a controlled stress rheometer. Fat and protein, although minor constituents of milled rice, were shown to have significant effects on the physicochemical and pasting properties of starches and flours. Removal of protein and lipids with aqueous alkaline or detergent solutions caused lower pasting temperatures and higher overall viscosity in both starches, compared with their respective flours. There was less viscosity difference between M202 flour and its starch when isolated by enzymatic hydrolysis of protein. The protease did not reduce internally bound lipids, suggesting that fats help to determine pasting properties of rice flours and their respective starches. Structural integrity differences in individual granules of waxy and nonwaxy rice flours, starches, and whole raw, soaked, and cooked milled grain were revealed by fracture analysis and scanning electron microscopy. Calmochi 101 and M202 did not differ in weight-averaged molar mass (Mw) and root-mean-square radii (Rz) between flours and starches, as determined by high-performance size exclusion chromatography (HPSEC) and multiple-angle laser light scattering (MALLS) (Park, I.; Ibanez, A. M.; Shoemaker, C. F. Starch 2007, 59, 69-77).     

Starch Properties and Stability of Club and Soft White Winter Wheats from the Pacific Northwest of the United States

Based on examination of 192 club and soft white winter (SWW) wheat samples, club and SWW wheat flours showed comparable levels of starch damage and flour peak viscosity, while differing significantly in starch content. Varietal differences and growing conditions had strong influence on the characteristics of both classes of wheat flour. Club wheat flour exhibited better stability in starch content and starch damage than did SWW wheat flour. A significant correlation between starch damage and cookie diameter in both club and SWW wheat was observed (r = -0.480, P < 0.0001 for club wheat and r = -0.430, P < 0.0001 for SWW wheat). Sponge cake volume was positively correlated with starch content in both classes of wheat (r = 0.362, P < 0.01 for club wheat and r = 0.181, P < 0.05 for SWW wheat). When wheat samples were grown in one location over three years, club and SWW wheat flours had comparable starch content. However, flour and prime starch peak viscosities were significantly different in club than in SWW wheat. Club wheat flour had lower starch damage and amylose content, as measured by high-performance size-exclusion chromatography (HPSEC), than did SWW wheat flour. Crop year and varietal differences had significant effect on amylose content, starch damage, and flour and starch peak viscosities, but not on starch content, in both classes of wheat flour. When wheat samples were grown in one year over seven locations, club wheat flour was higher in starch content, lower in starch damage, and comparable in amylose to SWW wheat flour. Both flour and prime starch viscosities were significantly higher in club wheat than in SWW wheat. Varietal differences and growing location had strong influence on starch properties in both classes of wheat. Peak viscosity of the isolated starch did not correlate well with the corresponding flour, indicating that flour pasting property does not reflect the pasting property of starch. The fine structure of isoamylase-debranched amylopectins from club and SWW wheats had a similar tri-modal pattern, with maximum at ≈DP 15 and two valleys at ≈DP 20 and 45, respectively. Although wheat flour samples differed widely in their prime starch peak viscosity, no significant difference between debranching patterns was obtained. These results indicate that the fine structure of amylopectin might not be responsible for the large differences in prime starch pasting property.