绿色富硒生物猪饲料中AFB1达标生产工艺优化研究

饲料中黄曲霉毒素(AFB₁)容易超标,检出率达80%~100%,毒性大,具强致癌性,可抑制生猪免疫机能,降低动物生产性能,引起动物继发感染,还会在动物产品中残留而威胁人类健康,给生猪养殖带来经济损失,降低猪肉食品安全性。本文通过使用先进固体发酵系统设备和益生菌发酵技术,采用单因素试验和响应面中试优化,获得发酵降解猪饲料AFB₁的最佳工艺参数为硒浓度0.3 mg/kg,发酵时间12 h,量子波强度30 Hz,益生菌菌种组合CGMCC NO.17328混合CGMCC NO.15611。该工艺将猪饲料AFB₁量从63.41μg/kg降解到2.98μg/kg,降解率达到95.30%,AFB₁含量达到国家饲料安全标准。生产工艺适合养猪场低成本快速生产AFB₁达标猪饲料。     

大型贯流式泵站快速门加速启动过渡过程

为研究大型贯流式泵站机组闸门加速启动过程中的外特性参数变化及流态变化,对灯泡贯流泵机组进行三维建模,采用Fluent软件中的UDF来控制闸门的启动过程,使用铺层法动网格技术来控制闸门处网格生成与消灭,并设定S-A模型作为湍流模型,对灯泡贯流泵机组启动过程进行瞬态数值模拟.计算结果表明:当贯流泵机组快速门以10倍设计速度启动时,机组的转速与流量将以更快的速度达到额定转速与额定流量,同时瞬间最大倒灌流量相比未加速启动时增加了30%.当贯流泵机组处于倒流状态时,靠近轮毂处叶轮叶道压力面的压强呈现出从叶轮进水边向出水边逐渐递增的分布规律.当机组处于零流量的临界状态时,混乱的流态导致压力集中及脱流现象加重,叶轮进水边负压区范围扩大且程度加深.     

苗期调控对晚播小麦产量及氮素利用的影响

针对冬小麦因播期推迟造成产量损失的问题,以2个不同分蘖能力的冬小麦品种中麦8号和航麦501为供试材料,研究苗期覆膜和补施氮肥对晚播小麦产量及氮素利用的影响。试验设置3个播期：10月5日适期播种（S0,对照）、10月15日适当晚播（S1）和10月25日过晚播（S2）。结果表明：随着播期推迟,小麦产量逐渐降低。晚播条件下,苗期覆膜和补施氮肥可调控冬小麦产量构成因素、农艺性状、茎蘖生长、成穗率以及氮素的吸收利用。综合而言,晚播条件下,覆膜和补施氮肥有利于提高小麦穗长、总小穗数及冬前群体数量;同时,覆膜可显著提高2个品种晚播条件下的分蘖成穗率和过晚播条件下的植株氮素积累量（PNA）及氮肥偏生产力（PFP）,增幅分别为46.4%~89.1%、12.7%~26.5%和19.5%~20.1%;补施氮肥在过晚播条件下有利于成穗率的提高,增幅为18.5%~34.7%。2种调控措施均有利于增加晚播小麦产量,增幅达1.4%~19.5%。但不同分蘖力的小麦对2种调控措施的响应存在差异。综合考虑产量及氮素利用等各方面因素,在晚播条件下,相比于补施氮肥,苗期覆膜更有利于提高晚播小麦产量,弥补晚播造成的产量损失,但在实际操作和节约生产成本方面,前者优于后者。     

森林康养步道五感体验需求与潜在游客体验意愿分析

【目的/意义】通过探索五感体验需求对潜在游客体验意愿的驱动影响,以期能够准确理解与把握潜在游客的行为意向,为森林康养步道设计提供理论参考。【方法/过程】以潜在游客为研究对象,借助AMOS构建结构方程模型,并引入“认知程度”这一调节变量进行层级回归分析。【结果/结论】结果表明:五感体验需求对潜在游客选择体验森林康养步道的意愿具有正向显著影响;在森林康养步道中,对五感体验需求影响最大的为触觉体验需求,其次为嗅觉体验需求、视觉体验需求和听觉体验需求,影响最小的是味觉体验需求;潜在游客对森林康养的认知程度对于五感体验需求与体验意愿之间的关系具有正向调节作用。     

Secondary Stress Responses in Juvenile Brazilian Flounder,Paralichthys orbignyanus,throughout and after Exposure to Sublethal Levels of Ammonia and Nitrite

This study investigated the secondary stress responses of Paralichthys orbignyanus exposed to ammonia and nitrite and after recovery. Fish were exposed to 0.12, 0.28, and 0.57 mg NH₃‐N/L, or 5.72, 10.43, and 15.27 mg NO₂‐N/L for 10 d followed by the same time length for recovery. Ammonia‐ and nitrite‐free water was used as a control treatment. Blood samples were collected after 1, 5, and 10 d of exposure and after recovery. Fish exposed to ammonia presented lower and higher glucose levels after 10 d of exposure and recovery, respectively. Ammonia induced initial and transient ionic disturbances and metabolic alkalosis. Nitrite exposure caused hyperglycemia, increased plasma K⁺ levels, and respiratory alkalosis, whereas metabolic acidosis was observed after recovery. Increased proportion of monocytes and/or granulocytes and reduced number of lymphocytes were demonstrated in fish exposed to 0.28 mg NH₃‐N/L (Day 1) and 10.43 mg NO₂‐N/L (Day 5) and after recovery in the 0.28 and 0.57 mg NH₃‐N/L treatments. Exposure to ammonia decreased the proportion of granulocytes on Day 5. In conclusion, exposure to concentrations at 0.12 mg NH₃‐N/L and 5.72 mg NO₂‐N/L provoked physiological disorders in Brazilian flounder. Nonetheless, fish exposed to 5.72 mg NO₂‐N/L following a 10‐d recovery period showed complete resumption of homeostasis.     

分段螺旋式甘草茎秆揉切装置设计与试验

针对全混合日粮饲草料揉切需求，该研究设计了一种分段螺旋式甘草茎秆揉切装置，对分段螺旋叶片的主体结构和搅龙结构参数进行设计，建立了刃口曲线方程，分析了装置揉切机理，并试制了分段螺旋式甘草茎秆揉切装置试验台。以搅龙转速、加工时间、填充系数、刀片与底壳间隙为因素，以粒度、破节率、单位质量能耗为指标，开展四因素三水平Box-Behnken试验，对试验结果进行方差分析和二次回归拟合，得出各因素对粒度影响显著性由大到小为加工时间、搅龙转速、填充系数、刀片与底壳间隙；对破节率的影响显著性由大到小为加工时间、填充系数、搅龙转速、刀片与底壳间隙；对单位质量能耗的影响显著性由大到小为填充系数、加工时间、搅龙转速、刀片与底壳间隙。对交互影响因素进行响应曲面分析并进行参数优化验证试验，结果表明：当搅龙转速为25 r/min、加工时间为12 min、填充系数为0.46、刀片与底壳间隙为15 mm时，甘草茎秆的揉切粉碎粒度为11.76 mm，破节率为83.27%，此时单位质量能耗为9 959.82 J/kg，试验值与模型理论值误差不超过7%，参数优化模型合理，满足作业要求。研究结果可为全混合日粮搅拌机的研发提供理论依据。     

长江流域棉花减量简化一次性施肥技术研究

针对棉花常规施肥技术存在的施肥次数多、技术复杂、用量大、利用率低、中后期土壤追肥操作不便、施肥易受天气影响等问题，研究了主栽棉花品种营养特性，研制了易降解棉花专用缓控释肥缓控释包膜新材料、系列配方，创新了生产工艺，研制的专用缓控释肥实现了棉花减量简化一次性施肥，变革了棉花施肥技术，解决了常规技术中施肥集中期与干旱雨涝等灾害高发期重叠导致的无法追肥或肥害、从而减产的重大难题。与等养分常规施肥相比，应用该技术棉花单产增加 3.8%～14.1%、增效10.1%～25.5%；减少施肥用工50%以上，等产量情况下单位面积减少施肥11.2%～52.3%。以棉花减量简化一次性施肥为核心技术，建立了棉花绿色轻简高效栽培技术体系。     

强化基层林业站职能作用 促进林业跨越式发展

基层林业站是国家设在基层的林业管理机构 ,在林业生产和建设中发挥着重要的职能作用。强化林业站的职能作用 ,必将对推动我国六大林业重点工程建设 ,实现林业跨越式发展起到巨大作用。     

山西东部林区灭火模式研究

对山西森林灭火模式进行了详细分析,提出了扑救山西东部林区的最佳灭火作战模式。     

Fundamental studies on wood/cellulose-plastic composites: effects of composition and cellulose dimension on the properties of cellulose/PP composite

Although wood/cellulose-plastic composites (WPC) of low wood/cellulose content have been more accepted worldwide and are promoted as low-maintenance, high-durability building products, composites containing high wood/cellulose content are not yet developed on an industrial scale. In this study, flow properties, mechanical properties, and water absorption properties of the compounds of cellulose microfiber/polypropylene (PP) and maleic anhydride-grafted polypropylene (MAPP) were investigated to understand effects of the high cellulose content and the dimensions of the cellulose microfiber. The molding processes studied included compression, injection, and extrusion. It was found that fluidity is not only dependent on resin content but also on the dimension of the filler; fluidity of the compound declined with increased fiber length with the same resin content. Dispersion of the composite was monitored by charge-coupled device (CCD) microscope. Increasing the plastic content in the cellulose-plastic formulation improved the strength of mold in addition to the bond development between resin and filler, and the tangle of fibers. The processing mode affected the physicomechanical properties of the cellulosic plastic. Compression-molded samples exhibited the lowest modulus of rupture (MOR) and modulus of elasticity (MOE) and the highest water absorption, while samples that were injection-molded exhibited the highest MOR (70 MPa) and MOE (7 GPa) and low water absorption (2%).