棉田土壤养分分析与土壤墒情监测系统应用

【目的】研究土壤养分的空间变异程度及分布规律,为该区域科学施肥提供依据。【方法】以新疆生产建设兵团第八师石河子总场六分场数字农业示范田为研究区域,应用土壤墒情监测系统、GIS与地统计学的方法,对棉田土壤含水量与温度进行实时采集、分析并存储在服务器里面,分析石河子总场土壤含水量和温度变化规律、棉田土壤养分空间分布特点及变异规律。【结果】(1)根据监测数据分析,随着灌水量增加和棉花生育期推进,上层0~30 cm比下层40~60 cm的土壤含水量变化趋势明显。0~20 cm土层土壤补偿水比较充分,各个监测点土壤含水量基本维持在比较适宜的范围内。土壤各层温度受大气温度影响并随着土层深度的加深而减弱,随着土层深度的逐渐加深滞后时间相对延长;受棉株逐渐长高变大以后遮阴等造成的影响,7月以后各土层温度逐渐持平,波动不大。(2)土壤全氮、速效磷和速效钾均呈现出中等程度变异;(3)土壤速效钾的块金值在25%~75%(块金值为0.497)表现为中等空间自相关性外,土壤全氮、速效磷指标的块金系数小于25%表现为强烈的空间自相关性。【结论】应用土壤墒情实时监测系统指导棉田灌溉,较往年没有任何减产减质的情况下,棉花灌溉在全生育期内比以往灌溉次数下降了1~3次,节约水资源约20%左右。研究区域内土壤全氮、速效磷和速效钾变异呈现中等程度变异特征,全氮、速效磷表现为极强空间自相关性,速效钾表现为中等强度的空间相关性。     

毛竹销（钉）的高速旋转摩擦焊接性能研究

选取毛竹销钉替代木榫在1 500 r/min的情况下与榉木基材进行旋转摩擦焊接，对其抗拉强度和焊接机理进行研究。重点研究不同形状的预钻孔和不同榫径与孔径比值下的竹销钉焊接抗拉拔强度，并将其与木榫焊接和PVAc胶接的抗拉强度进行对比。结果表明:1）当采用恒定直径孔10/9、10/8、10/7、10/6 4种榫径/孔径比的焊接强度均高于PVAc胶接强度，但低于木荷榫和榉木榫的焊接强度，其中10/8的榫径/孔径比的焊接强度相对最高，达到了5.54 MPa；2）当采用渐变直径孔，竹销钉的焊接强度得到明显提高。其中10/8-6的榫径/渐变孔径比值取得了最高的焊接强度，达到6.42 MPa，比10/8比值的强度提高了15.6%，超过了木荷榫的焊接强度，但不及榉木榫的焊接强度；通过对竹销钉的焊接界面温度进行监测，发现焊接界面能在2 s内达到300℃以上的峰值高温，且维持了一定的高温时间（通常约2～3 s），随后随着竹销停止旋转摩擦，温度逐步下降；不同的榫径与孔径比值下，焊接界面的升温速率、峰值温度和高温持续的时间不同，它们是产生强度差异的主要原因；SEM观察结果显示，竹销旋转摩擦焊接界面由竹销或基材中的胞间层物质软化、熔化和流动并与作为增强材料的竹纤维包裹，形成了犹如“钢筋水泥土”结构般的致密、连续和坚固的焊接界面；FTIR分析结果表明，摩擦产生的高温会导致竹销中半纤维素发生一定程度的降解，纤维素的降级十分有限，木质素发生一定程度的缩合反应，木质素的含量相对提高。试验结果表明，将竹销钉代替木榫用于木材的旋转摩擦焊接是可行的。     

广西某食蟹猴规模化养殖场饮用水和青饲料卫生质量监测

为了对广西某规模化食蟹猴养殖场饮用水和青饲料卫生质量情况进行监测,对饮用水和青饲料进行连续抽样监测,按照《生活饮用水卫生标准》《生活饮用水卫生标准检验方法》和《国家禁用和限用的农药名单》进行检测与评价。结果显示:抽取6份饮用水样检测26项理化指标,有3份不合格,超标率达50.0%,超标指标有浑浊度、肉眼可见物;抽取147份饮用水检测微生物指标,有22份超标,超标率达15.0%,超标微生物指标为细菌总数、总大肠菌群、耐热大肠菌群和大肠埃希氏菌;抽取13个品种青饲料48份检测10种禁用农药残留情况,甲胺磷、敌敌畏、乐果、氧化乐果、氰戊菊脂、多菌灵、啶虫脒、吡虫啉、三唑磷、毒死蜱检出率分别为2.1%、0、0、0、0、12.5%、2.1%、12.5%、2.1%、2.1%。说明该规模化食蟹猴养殖场饮用水存在不合格情况,青饲料检出农药残留。     

An acoustic based approach to evaluate the effect of different diet lengths on feeding behavior of Litopenaeus vannamei

Studying shrimp feeding behavior is challenging and, traditionally, studies have been using direct visual observation or video recordings with image analysis under laboratory conditions. Passive acoustics monitoring (PAM) is a non-invasive approach to study feeding behavior of penaeids, as their mandibles emit clicking sounds during feed ingestion. Considering the wide variation available in shrimp diet lengths, our knowledge is still limited about their effects on feeding behavior. The present study was designed to use acoustics to evaluate the feeding behavior of Litopenaeus vannamei fed different diet lengths. A commercial pelleted diet with similar diameter (2.4 mm) and three different lengths was used as treatments “small” (2.35 mm), “medium” (4.26 mm) and “large” (8.42 mm). Three separate trials were performed with fastened shrimp (20 g), using omnidirectional hydrophones and external audio recorders. Our approach started with the characterization of the click acoustic parameters produced by three shrimps when fed the different diet lengths in anechoic chambers (15 L). We then analyze the number of clicks produced per pellet and duration of the clicking activity when shrimp fed a single pellet in individual tanks (1 L). Finally, the acoustic energy of feeding activity and feed consumption, as well as theirs relationship to predict feed intake was evaluated in aquaria (70 L) with five shrimps. The acoustic parameters of isolated clicks were not affected by the different diet lengths, however, doubling the length of the pellet resulted in doubling the number of clicks emitted during feeding activity. The duration of clicking activity per pellet indicated that small pellets are consumed 2.9 and 4.7 times faster than medium and large pellets, respectively. Furthermore, feeding acoustic energy of small pellets decreased rapidly after feed offer, as their faster consumption probably contributed to shrimps achieved satiety earlier than larger diets. Feed consumption was similar among diets length, but significantly correlated with the feeding acoustic energy emitted by L. vannamei, which is a breakthrough in feeding behavioral research. The results highlight the potential and possibilities of an acoustic approach to estimate feed consumption, as well as an alternative to traditional methods in feeding behavioral studies to improve efficiency of feed management.     

基于多反应监测质谱技术的水稻叶片蛋白绝对定量方法

【目的】建立水稻叶片蛋白的多反应监测(MRM)质谱绝对定量方法。【方法】水稻叶片蛋白经含1.0%十二烷基硫酸钠(SDS)的磷酸盐(PBS)缓冲液提取,丙酮沉淀除杂纯化、胰蛋白酶消化,酶解液经液相色谱分离,MRM质谱监测,外标法定量。【结果】向提取缓冲液中加入1.0%SDS可增强水稻叶片中16种靶蛋白和总蛋白质的提取效果;不同有机试剂处理,总蛋白质沉淀量存在显著差异(P<0.05),沉淀能力从强到弱依次为乙腈>丙酮>异丙醇>甲醇>乙醇;对于16种目标蛋白,总体以丙酮沉淀效果最好,其次是异丙醇和乙腈,甲醇和乙醇效果较差。该方法线性范围均达到3个数量级,定量限为0.1~2.5 nmol/L,灌浆期16种水稻叶片蛋白质含量为6.0~2818.1μg/g,相对标准偏差均小于14%。【结论】SDS可显著提高水稻叶片蛋白提取效果,采用丙酮或乙腈可获得较好的蛋白沉淀效果,但不同蛋白质略有差异。结合MRM质谱监测技术可实现水稻叶片蛋白的绝对定量,方法线性范围宽、敏度高、重复性好。     

System for quasi‐continuous simultaneous measurement of oxygen diffusion rate and redox potential in soil

Oxygen diffusion rate (ODR) and redox potential (E_H) are quantitative indices representing oxygen availability and redox status in soils, which is valuable information for better understanding causes and effects of soil aeration. Because these indices are spatially and temporally highly variable, continuous measurements and adequate numbers of repetitions are essential for accurate in situ monitoring. Here, we present a new, fully automated recording system for in situ measurements where ODR and E_H are measured at the same platinum electrode. The conflict between electrode polarization for ODR and the resulting biased E_H readings is solved by reducing the polarization time and introducing a recovery interval between two consecutive measurement cycles. The shorter polarization time ensures accurate E_H readings. It also results in moderately overestimated ODR readings, but this can be corrected before data analysis. The recovery interval restricts temporal resolution of the E_H‐ODR data pairs to 8 h. We illustrate the use of the system with measurements in a field experiment in Zürich, Switzerland. ODR curves at different depths ran roughly parallel to the corresponding curves of O₂ concentration in soil air but ODR was much more sensitive to precipitation. Low ODR was a necessary but not a sufficient condition for declining E_H. E_H ran parallel to O₂ concentration in soil air rather than to ODR. The fully automated system allows for time series of replicate measurements in multifactorial field studies with reasonable labor requirements. It may be particularly suitable for studies examining the effects of soil tillage, compaction, and irrigation, where structure‐related soil properties such as porosity, gas permeability, and soil aeration play a dominant role.     

大豆PHD家族蛋白的全基因组鉴定及表达特征分析

PHD（Plant Homeodomain Finger）基因家族编码一类锌指转录因子,广泛参与植物的生长发育和逆境应答过程。通过全基因组鉴定获得了95个大豆PHD家族蛋白。通过共线性分析、进化树构建、基因结构和功能结构域鉴定、GO注释分析、不同组织间和非生物胁迫下表达分析等,获得了大豆PHD家族基因复制、家族进化、保守结构域及基因表达等信息。结果表明,大豆PHD基因在家族进化、基因结构和保守结构域上存在较大变异,可能参与Zn ²⁺结合、DNA结合及表观遗传调控等分子过程,参与调控植物生长发育和逆境应答。这些结果为进一步研究大豆PHD家族在生长发育和逆境应答中的生物学功能提供重要线索。     

脱涡致振式压电风力发电机性能分析与试验

为满足农业遥感监测系统的供电需求，减少化学电池对水和土壤的污染，提出一种脱涡致振式压电风力发电机，并从理论和试验两方面进行了研究。建立了脱涡致振式压电风力发电机的理论模型，通过仿真分析研究迎风角、压电振子长度及风速对压电振子变形量的影响，并对发电机样机进行了测试试验。结果表明，不同风速下均存在两个最佳迎风角，使发电机输出电压较大，压电振子长度为60、78mm，风速为7.6、11.6、12.4m/s时的两个最佳迎风角分别为(35°,135°)、(45°,125°)、(50°,120°)和(35°,120°)、(40°,115°)、(45°,110°)。当迎风角为120°时，存在最佳风速，使发电机输出电压达到最大；随着压电振子长度的增加，最佳风速由12.4m/s降低到8.4m/s，其对应的最大输出电压由16.6V增加为16.8V。当外接电阻为150kΩ、迎风角为30°时，试验测得最大输出功率为1mW。研究表明，根据实际风速确定合理的迎风角及压电振子长度可提高发电机的发电能力。     

基于农用STM32的电动机转速监测系统设计

农业作业环境复杂,实时监控农用电动机转速对判断电动机运行状况具有重要意义。笔者设计了一种电动机转速监测系统,该系统主要由光电开关传感器、触发圆盘、OLED、STM32单片机组成,通过单片机的定时器中断和外部中断功能,可实现对电动机转速的实时监控,通过IIC通信技术,可实现转速数据的可视化。该系统抗干扰能力强、精度高、实用性强,适用于恶劣的农业作业环境,同时为其他转速监测方案提供了设计依据。     

生态文明视域下草原治理体系构建研究

草原是我国面积最大的陆地生态系统，既是我国重要的生态安全屏障，也是广大农牧民赖以生存的家园。为深入贯彻习近平生态文明思想，落实山水林田湖草沙系统治理的理念，推进草原保护修复和高效利用，本研究结合"十四五"林业和草原保护发展规划纲要，提出了构建草原监测评价体系、草原保护体系、草原生态修复体系、草原执法监管体系、现代草业体系、支撑保障体系等草原治理体系，旨在为推进草原治理体系和治理能力现代化提供参考。