快速检测木材微纤丝角的近红外光谱分析技术

介绍了一种新的测量木材微纤丝角的无损检测技术--近红外光谱分析,并详细阐述了测量时木材样品的选择及制备,测量工作包括X射线衍射和近红外光谱采集、多变量数据分析与模型建立的方法及步骤.证明了近红外光谱分析技术可以用于快速准确地预测木材的微纤丝角.     

Surface energy of preservative-treated southern yellow pine (Pinus spp.) by contact angle measurement

In this study, the contact angles of four different reference liquids (including distilled water, diiodomethane, formadide and glycerol) formed on the surfaces of wood, treated with chromated copper arsenate (CCA) and two other emerging copper-based water-borne systems (commercial names: NW and NS) were measured with sessile drop method. Based on the contact angle data, the surface energy was obtained from the acid-base approach. The total surface energy consisted of Lifshiz-van der Waals parameter and acid-base parameter. Results showed that the NW and CCA treatments made the wood surface more hydrophobic while the NS treatment had the reverse effect on the wood surface mainly owing to the increased penetration of earlywood. By using three liquids, diiodomethane, formamide and distilled water, the total surface energy obtained for untreated earlywood, untreated latewood, CCA-treated earlywood, CCA-treated latewood, NW-treated earlywood, NW-treated latewood, NS-treated earlywood and NS-treated latewood were 43.1, 44.5, 43.4, 45.1, 49.4, 40.6, 46.0 and 40.9 mJ/m², respectively. The surface energy of CCA-treated wood was almost the same as untreated wood. After NW and NS treatments, the surface energy of both earlywood and latewood changed a little. However, the change was not so obvious as to draw any further conclusion concerning the influence of NW and NS treatments on the surface energy of wood. __________ Translated from Journal of Beijing Forestry University, 2006, 28(4): 1–4 [译自: 北京林业大学学报]     

森林结构调查最小面积的研究

采用4块100m×100m的天然林样地材料,分别利用角尺度和双相关函数分析4块大样地中不同面积的窗口(小样地)对应林木个体的空间分布格局。结果表明,小样地面积不同其对应林木的空间分布格局也不同,随着样地面积逐渐变大,对应林木的空间分布格局趋于稳定,这意味着森林结构分析必须在一定大小的样地上进行。根据本研究资料,样地面积最小应为2500m2。     

Tensile strength of softwood butt end joints. Part 1: Effect of grain angle on adhesive bond strength

To study the effect of grain angle on the adhesive bond strength in wood, three-part Norway spruce wood specimens were bonded and tested in tension. The two axially orientated outer parts of the specimens were joined with the middle part by means of three adhesives typically used for load-bearing constructions, i.e. one-component polyurethane (PUR), melamine-urea-formaldehyde (MUF) and phenol-resorcinol-formaldehyde (PRF). The grain angle of the middle part was varied from 0° (end grain to end grain) to 90° (flat grain to end grain) in incremental steps of 10°. In general, PRF- and MUF-bonded samples exhibited highest tensile strength at end grain to end grain orientation of the three parts, while specimens bonded with PUR showed only 25% of the strength measured for PRF and MUF, respectively. At high grain angles (90°) all specimens showed similar strength values in the range of 30% of maximum strength of MUF- and PRF-bonded specimens. To explain the changing strength levels at different grain angle a composite failure criterion was applied.     

喷雾干燥过程中产品玻璃化温度转变和质量控制

通过分析物料在整个喷雾干燥阶段中的温度和颗粒状态变化,研究物料的玻璃化转变特性和产品质量与干燥工艺参数的关系,得出了相应的结论,并提出了因颗粒玻璃化转变的原因造成产品的质量变化的调整方法.     

飞机喷洒Bt粉剂防治天然胡杨林春尺蠖技术

应用Y-5B型飞机低量喷洒16 000 IU/mg的Bt可湿性粉剂防治天然胡杨林春尺蠖,用量为1 500 g/hm2和1 200 g/hm2。结果表明两种剂量都具有高效持效的特点,1 200 g/hm2可使虫口减退率达到97%,有效地减轻了春尺蠖对新疆天然胡杨林的危害,防治成本有所下降。     

Crystallinity of wood and the size of cellulose crystallites in Norway spruce (<Emphasis Type="Italic">Picea abies</Emphasis>)

X-ray diffraction was used to study variations in the crystallinity of wood and the average thickness and length of the crystallites of cellulose as a function of the number of the year ring in Norway spruce [Picea abies (L.) Karst.]. The crystallinity increased from ring 4 to ring 10 from the pith and was constant after ring 10. The crystallinity of mature wood was about 30% ± 5%. The average thickness and average length of the crystallites were 3.2 ± 0.1nm and 28 ± 2nm, respectively; and no systematic variation of these values with the number of the year ring was observed. The mean microfibril angle decreased near the pith but was constant in the mature wood.     

长白落叶松人工林树冠形状的模拟

以长白山地区 2 6a生长白落叶松人工林为研究对象 ,采用枝解析的方法 ,测定了 2 5株林木 (直径 10 5～2 4 9cm)的树冠变量 ,并建立了预测树冠外侧形状的冠形模型。基于枝条着枝深度 (DINC)和林木变量所建立的树冠形状模型包括 :基径、枝长、着枝角度和弦长等预估模型。对于大小相同树木的主要枝条来讲 ,这些树冠变量是随着DINC的增加而增大 ;而林木的胸径 (DBH)和树高 (HT)变量很好地反映了不同大小树木的冠形变化。冠形预测模型预测效果良好 ,充分体现了树冠结构的变化趋势 :树冠形状在树冠的中上部呈抛物线体 ,而在树冠的下部则为近圆柱体。文中所建模型 ,可以合理地描述长白落叶松人工林的树冠形状及其变化规律。     

日本落叶松无性系微纤丝角遗传变异的研究

对10个10年生日本落叶松无性系的早材和晚材微纤丝角进行了测定,结果表明:早、晚材微纤丝角无性系间差异极显著,同一年轮内早材微纤丝角大于晚材.日本落叶松微纤丝角的径向变异规律为:在髓心处最大,以后逐渐减小.早、晚材微纤丝角与树木年轮间的变异模式(径向变异)以对数和乘幂式方程拟合效果较好,R2(R为相关系数)均在0.8以上.早、晚材微纤丝角同树高、形率、树皮厚度、主枝粗、枝干比、主枝夹角、主枝长的相关关系不显著,早、晚材微纤丝角同胸径、冠幅的相关关系达到显著水平;早材与晚材的微纤丝角也相关显著.早材和晚材的微纤丝角受中到强度遗传控制,广义遗传力分别为0.767 4、0.804 3.按照20%的选择率,早材和晚材的微纤丝角的遗传增益分别为21.82%和29.75%.     

杨树微纤丝角的变异及其与木材性质的相关关系

微纤丝角为细胞次生壁S2层微纤丝排列方向与细胞主轴所形成的夹角,与木材的物理性质、力学性质和化学性质都有着直接的关系。应用x射线衍射法测定了7个杨树无性系(14株样木)胸径处各年轮的微纤丝角,并对应分析和测定了各年轮的木材基本密度、纤维长度、纤维宽度和纤维素含量。研究结果表明,杨树微纤丝角在年轮间存在显著差异,其径向变异规律为从髓心向外以微纤丝角逐渐降低,年轮间的平均微纤丝角在7.8旱?8褐洌荒静幕久芏取⑾宋ざ取⑾宋矶群拖宋睾吭谀曷旨湟泊嬖谙灾钜臁O喙胤治霰砻鳎⑾怂拷怯肽静幕久芏取⑾宋ざ取⑾宋矶群拖宋睾看嬖谙灾母合喙毓叵??0.01),相关系数分别为-0.450、-0.586、-0.516和-0.660。回归分析结果表明,多项式方程可较好地描述杨树微纤丝角与所测定的木材性质的关系,相关系数均在-0.45以上(n=125)。本文的研究结果认为,在今后针对杨树材性改良的育种计划中,微纤丝角是一个重要的选育和改良指标。图3表3参34。