Air Classification of Pin‐Milled Soybean Hulls

Commercial soybean hulls (14.6% crude protein) were pin milled and then air classified into five fractions to determine whether the hull structure can be disrupted and the protein constituents concentrated. The number of pin millings had only a small effect on the weight distribution of the five fractions. After one grinding, the sum of fractions 1 and 2 (<15–18 μm) represented only 3% of total hulls, and on three grindings, they amounted to only 6% of the hulls. Fraction 3 (19–24 μm) shifted from 16 to 20% with three grindings, while fraction 4 (25–30 μm) remained unchanged at 5%. Fraction 5 (>30 μm) shifted from 75 to 69% on three pin millings to compensate for the shifts noted in fractions 1–3. Scanning electron microscopy revealed that fractions 1 and 2 consisted of the parenchymal cell layers (innermost portion) of the hulls; these fractions had three times the protein content and more than twice the amount of lipids found in the ground starting material. Fraction 3 contained many of the hourglass cells typically found in the middle layer of the hulls plus parenchyma cell material and exhibited about twice the amount of protein and lipid found in the starting hulls. Fraction 4 included large hourglass cells plus globular material and contained about twice the amount of protein and about one and one‐half times the lipid of the starting material. Fraction 5 consisted primarily of clumps of palisade cells (outer cellular layer) adhering to each other and had a lower protein and lipid content than the starting hulls. Thus, pin milling causes some selective disruption of the hulls where parenchyma cell layers and hourglass cells are partially released. The palisade cells, however, are the most difficult to disrupt and constitute the fraction most resistant to pin milling. Our findings suggest that pin milling soybean hulls in combination with air classification can be used to concentrate the proteins and lipids in the fines fractions.     

Growth performance of blue shrimp, Litopenaeus stylirostris in self-cleaning microcosm tanks

Outdoor microcosm tanks were used to grow the penaeid blue shrimp, Litopenaeus stylirostris, in Brunei Darussalam. The tanks were cylindrical, free standing fiber glass tanks of 1827 L water holding capacity and had a self-cleaning mechanism. In three eight-week feeding trials, juvenile shrimp of 0.9–4.3 g were stocked at a density of 28 shrimp/m². At the end of each trial, survival rates exceeded 80%. Growth rates ranged from 1.19 to 2.46 g/week. Water quality remained stable and within suitable ranges for L. stylirostris growth in all trials. The tanks had algae and bacterial floc developing within a few days of starting the trials. Fourteen commercial shrimp feeds, each containing more than 40% crude protein, were tested in the trials. In spite of the presence of natural food organisms, significant feed-related differences among treatments were found in each trial. In conclusion, microcosm tanks support excellent growth and survival of L. stylirostris and are appropriate for conducting trials to evaluate feeds for pond growout.     

Characteristics and Quality of Japanese Traditional Fermented Soybean (Natto) from a Low-phytate Line

Plant Foods for Human Nutrition - The Japanese traditional fermented soybean or “natto”, a cheap and nutrient-rich food, is very popular in Japan. The low-phytate (LP) soybeans exhibit...     

Demonstration and validation of enhanced monitored natural recovery at a pesticide-contaminated sediment site

Purpose

Monitored natural recovery (MNR) combined with a thin-layer cap (TLC), often referred to as enhanced monitored natural recovery (EMNR), has the potential to accelerate and improve the effectiveness of MNR as a remedial strategy while minimizing widespread disturbance to the existing habitat. This study evaluated the effectiveness of a nominal 15-cm thin-layer sand cap as an EMNR remedial strategy to address sediments that were moderately contaminated with the chlorinated pesticide dichlorodiphenyltrichloroethane and its derivatives, collectively DDX.

Materials and methods

Physical, chemical, and biological measurements were conducted pre-remedy placement and 2, 14, and 25 months post-placement. Measurements were used to evaluate (1) TLC stability; (2) bottom-up mixing of the TLC; (3) advection through the TLC; (4) characteristics of newly deposited sediment atop the EMNR layer compared to pre-remedy surface sediment conditions; (5) changes in contaminant bioavailability; and (6) physical impacts to the benthic community.

Results and discussion

Significant reductions were observed from measurements conducted pre- and post-placement in surface sediment (84–97%), porewater (33–75%), and tissue concentrations (Lumbriculus variegatus deployed in situ) (72–82%). A 63 to 72% decrease in DDX depositional mass flux also was observed. Multiple lines of evidence indicated that the TLC material remained stable. Deposition of suspended material with low concentrations of DDX influenced low concentrations in the surface sediments. No adverse effects were observed on the benthic invertebrate community after TLC placement, and ecological metrics indicated increases in benthic community health, even in the short time period (2 months) following TLC placement.

Conclusions

This demonstration showed that EMNR can be effective at reducing biological exposure in surface sediments while minimizing short-term disturbances to benthic communities at sites where MNR is a remedy option, but natural deposition rates are inadequate to achieve cleanup goals within a reasonable timeframe.

     

Strategies for improving fuel efficiency in the Portuguese trawl fishery

The recent rise in oil prices has brought renewed attention to energy savings in the fishing industry, and particularly in trawling. Coastal trawlers spend most of their time on fishing grounds near the coast. In such cases, the most successful energy-saving modifications ought to result from changes in the fishing gear and towing conditions. The purpose of this study was to identify the energy-economy potential for Portuguese fish trawlers after altering a vessel's operating conditions and improving its trawl gear performance. Two trawlers, named Tricana de Aveiro and João Macedo were selected as subjects in this project. Both vessels work with gear of similar design and size. Experimental sea trials were carried out to elucidate the actual vessel and gear performance. A model trawl was then built and tested in a flume tank, which provided the basis for improving the gear design. Full-scale trials were then carried out with both vessels using the modified trawls in order to assess changes in gear performance. The new trawls maintained their previous ability to catch species of different ecological groups and consumed less fuel at the same commercial trawling speed. An economic study showed potential increases in the net cash flow (NCF) of up to 27% over the range of operational navigation and trawling speeds. Having demonstrated the performance of the new trawls, the skippers of both vessels subsequently adopted the new design for commercial fishing.