Development of a CO2 gas analyzer for monitoring soil CO2 concentrations

Measurement of soil CO₂ concentrations is important for investigating the dynamics and diffusion of CO₂ in soil. In this study, we developed a small CO₂ analyzer for measuring in situ-soil CO₂ concentrations. The CO₂ analyzer consists of a module containing an infrared CO₂ gas sensor, a temperature sensor, and a relative humidity sensor. These sensors are installed in a protective box with an air vent, which is suitable for burying in the soil. The output response time of the CO₂ analyzer was 349 s, as evaluated from the phase lag after input of known CO₂ concentrations. This response time is short enough to measure soil CO₂ concentrations, because variations in concentration are slower than the response time of the analyzer. In a field test, we used the CO₂ analyzer to measure soil CO₂ concentrations at five depths (0–50 cm) over 2.5 months. While the CO₂ concentration generally increased with depth, the amplitude of the variation in CO₂ concentration decreased with depth. The phase lag of the variations in soil CO₂ concentration also increased with depth, as did soil temperature. The tests confirm that the CO₂ analyzer is applicable to continuous monitoring of soil CO₂ concentrations.     

Biological performance of <Emphasis Type="Italic">Eucalyptus camaldulensis</Emphasis> leaf oils from Thailand against the subterranean termite <Emphasis Type="Italic">Coptotermes formosanus</Emphasis> Shiraki

The antitermitic activities of leaf oils and their constituents, taken from three clones of Eucalyptus camaldulensis Dehnh. in Thailand, against Coptotermes formosanus Shiraki were investigated in contact and noncontact tests. The termiticidal mechanism was also examined. Antitermitic tests demonstrated that E. camaldulensis leaf oils were both contact toxicants and fumigants to C. formosanus with LC₅₀ values ranging between 12.68 and 17.50 mg/g by the contact method, and between 12.65 and 17.50 mg/petri dish (100 cm³) by the noncontact method. p-Cymene and γ-terpinene were primarily responsible for the contact toxicity and 1,8-cineole was responsible for fumigation. From the investigation of termiticidal mechanism, E. camaldulensis leaf oils exhibited the inhibition of acetylcholinesterase activity and showed the common symptoms of a neurotoxic mode of action against C. formosanus. Part of this report was presented at the 58th Annual Meeting of the Japan Wood Research Society, Tsukuba, March 2008     

Changes in wood temperature under high-speed friction

Thermal effects at the surface of a sample wood specimen while it is rubbed by reduction with a metal disk rotating at high speed are investigated. The results provide fundamental data for the development of new surface processing methods. The results of high-speed friction tests showed that the wood surface developed high-temperature regions due to the effect of friction heat, and deformed tissue was observed at the wood surface in the region that experienced the rubbing action. The thermal effects extended to a deep range in the deformed region by reduction due to different fiber inclination angles, both parallel and normal to the friction surface. The thermal effects from the rubbed conditions of the reduction and feed speed also extended deeply into the region deformed by reduction, although the thermal effect was decreased at higher feed speed. From the results of these friction tests, the change in wood temperature is described unambiguously by factors related to pressure on the friction surface.     

Analysis of volatile compounds released during the grinding of roasted coffee beans using solid-phase microextraction

A dynamic solid-phase microextraction (SPME) method to sample fresh headspace volatile compounds released during the grinding of roasted coffee beans was described and the analytical results using gas chromatography/mass spectrometry (GC/MS) and GC/olfactometry (GC/O) were compared to those of the conventional static SPME sampling methods using ground coffee. Volatile compounds released during the grinding of roasted coffee beans (150 g) were obtained by exposing the SPME fiber (poly(dimethylsiloxane)/divinylbenzene, PDMS/ DVB) for 8 min to nitrogen gas (600 mL/min) discharged from a glass vessel in which the electronic coffee grinder was enclosed. Identification and characterization of volatile compounds thus obtained were achieved by GC/MS and GC/O. Peak areas of 47 typical coffee volatile compounds, separated on total ion chromatogram (TIC), obtained by the dynamic SPME method, showed coefficients of variation less than 5% (n = 3) and the gas chromatographic profile of volatile compounds thus obtained was similar to that of the solvent extract of ground coffee, except for highly volatile compounds such as 4-hydroxy-2,5-dimethyl-3(2H)-furanone and 4-ethenyl-2-methoxyphenol. Also, SPME dilution analysis of volatile compounds released during the grinding of roasted coffee beans showed linear plots of peak area versus exposed fiber length (R (2) > 0.89). Compared with those of the headspace volatile compounds of ground coffee using GC/MS and GC/O, the volatile compounds generated during the grinding of roasted coffee beans were rich in nutty- and smoke-roast aromas.     

Relationship between wettability and sizing degree of paper containing bulking agent

The addition of a bulking agent achieves the bulking of paper and increases the pore volume. In this study, the effect of adding bulking agents with various alkyl chain lengths (C₁₄, C₁₈, and C₂₂) on the bulk of paper, the sizing performance, and sheet wettability was evaluated. The bulking effect of a bulking agent with a short alkyl chain length (C₁₄) was large, and reduction in the sheet tensile strength was confirmed to be suppressed. Good sheet sizing performance was achieved when a bulking agent was used with an alkyl ketene dimer (AKD). When 0.1% or more of AKD was added, using a bulking agent with a shorter alkyl chain length increased the improvement in the sizing degree. Pyrolysis gas chromatography measurements of the amount of reacted AKD revealed that the addition of a bulking agent increased the AKD content of the sheet. The sheet contact angle measured by the two-liquid method tended to increase with increasing alkyl chain length. However, the sheet contact angle was not directly correlated with the Stöckigt sizing degree. By using 1% ferric chloride (FeCl₃) and 2% ammonium thiocyanate (NH₄SCN) aqueous solution, which are used for measuring the Stöckigt sizing degree, the time-dependent change in the contact angle on the paper sheet surface was measured to evaluate wettability. The Stöckigt sizing degree of paper sheets was found to be greatly influenced by the sheet wettability by NH₄SCN solution. In the case of 2% NH₄SCN aqueous solution, different samples exhibited large wettability differences. When 0.2% or less of AKD was added, the effect of the concentration on the contact angle was confirmed to be large at all NH₄SCN concentrations.     

Selection of plant population of kenaf (Hibiscus cannabinus L.) as a papermaking raw material on arid hillside land in China

Agronomic properties (whole stalk yield, fiber length distribution, chemical composition) and whole stalk kraft pulp characteristics (total pulp yield, pulp fiber length distribution, pulp sheet strengths) were examined for kenaf (variety Zhehong 8310) at four plant populations, ranging from 135 000 to 405 000 plants/ha on arid hillside land at Anji, Zhejiang, China. For agronomic properties, the final whole stalk yield was higher as the plant population increased and as the altitude of the location on the slope decreased. Average fiber lengths of bast and core showed maxima at 225 000 plants/ha. Cellulose content increased as the plant population increased. For the kraft pulp characteristics of kenaf whole stalk, the total pulp yield was lower as the plant population increased, with the maximum difference about 1.3%. Sheet strengths and average fiber length attained maxima at around 225000–315000 plants/ha. The largest pulp strengths (breaking length, burst index, and folding endurance) were seen at a plant population of 225000 plants/ha, and the largest tear index was seen at a plant population of 315 000 plants/ha. When the agronomic properties and whole stalk kraft pulp characteristics were combined, a plant population between 225 000 and 315 000 plants/ha, which is a little higher than that of kenaf bast production for textiles, was selected as the optimum cultivated kenaf plant population for whole stalk kraft pulp and papermaking on arid hillside land in China.