湿地松与马尾松人工林木材物理力学性质的比较研究

通过对湿地松和马尾松人工林木材物理力学性质的测定和比较分析,结果表明:湿地松人工林木材密度、干缩系数和除冲击韧性以外的力学强度均稍大于马尾松人工林木材,而冲击韧性则恰恰相反.经差异显著性t检验表明:湿地松和马尾松木材物理力学性质指标中顺纹抗压强度、抗弯强度、弦面顺纹抗剪强度和冲击韧性差异极显著,气干密度、基本密度、径面顺纹抗剪强度和端面硬度差异显著,除此之外的其余指标差异不显著.     

枫香人工林和天然林木材物理力学性质比较

通过对枫香人工林和天然林木材物理力学性质的测定和比较分析 ,结果表明 :枫香天然林木材物理力学性能略优于人工林 ,而木材物理力学性质的均匀性略差于人工林 ;经差异显著性t检验表明 :枫香人工林和天然林木材物理力学性质指标中除径面顺纹抗剪强度和抗劈力差异显著外 ,其余指标差异不显著     

慈竹材物理力学性质研究

对四川江油1～3年生慈竹材主要物理力学性质进行了测定与分析,结果显示:竹材气千密度,全干密度,基本密度,顺纹抗压强度,顺纹抗剪强度随竹龄和竹秆高度的增加而增加:径、弦向全干缩率随竹龄和竹秆高度的增加而减小:径向全千缩率大于弦向:竹壁厚度随竹龄的增加而增厚,随竹秆高度的增加而减小.方差分析表明,竹材全干密度,基本密度,径、弦向全干缩率,顺纹抗压强度随竹龄变化在0.001水平显著;全千密度,竹壁厚度,顺纹抗剪强度随竹秆高度变化在0.001水平显著.     

木材顺纹抗剪强度测试方法的改进

在测量小径材或薄板抗剪强度时．常由于材料尺寸过小,无法按国标规定制作试样。本文提出了一个木材顺纹抗剪强度测试方法的改进方案,即在基本保持试样原有力学性状不变的前提下．将剪切试样的宽度缩小为国家标准试样的一半,并通过杉木和I-214杨的标准试样和改进试样的对比试验．论证了改进方案的可行性。对比试验表明：改进试样和标准试样的抗剪强度差异不显著(0．05水平)。二者强度平均值相对差异的绝对值低于3％。     

硫酰氟熏蒸处理对出口包装樟子松木材力学性能的影响

采用硫酰氟作为熏蒸剂处理樟子松木材,在试验室条件下,研究熏蒸处理对木材的抗弯强度、抗弯弹性模量、颇纹抗剪强度和颇纹抗压强度的影响。结果表明,经硫酰氟熏蒸处理后樟子松木材的抗弯强度、抗弯弹性模量、顺纹抗剪强度和顺纹抗压强度均有程度不同的变化;除顺纹抗剪强度有所增强,抗弯强度、抗弯弹性模量和顺纹抗压强度均减小;抗弯强度和抗弯弹性模量的相关性有所下降。     

不同立地条件香椿人工林木材材质的比较

通过对不同立地条件下香椿人工林木材物理力学性质的测定和比较分析表明:香椿人工林木材密度和干缩性随着立地级的提高而减小;木材顺纹抗压强度、抗弯强度和硬度:Ⅰ级地<Ⅱ级地<Ⅲ级地,抗弯弹性模量、抗劈力、冲击韧性:Ⅱ级地>Ⅰ级地>Ⅲ级地,顺纹抗剪强度:Ⅱ级地>Ⅲ级地>Ⅰ级地。差异显著性t检验表明:香椿人工林木材密度Ⅰ级地、Ⅱ级地、Ⅲ级地间差异不显著。香椿人工林木材干缩性和力学性质指标Ⅰ级、Ⅱ级、Ⅲ级地3者间有的指标差异极显著,有的指标差异显著,大部分指标差异不显著。     

荆条藤柳力学性质的测试与对比研究

以荆条为重点,棕榈藤、沙柳材为比照,结合荆藤柳材的圆形截面设计试样,测定了抗弯强度和弹性模量、顺纹和横纹抗压强度、顺纹抗拉强度、抗剪强度、扭曲强度、冲击韧性、抗劈力、握钉力各项力学指标。荆条的各项力学强度指标中,抗弯强度最大,其次是顺纹抗拉强度,顺纹抗压强度和扭曲强度也较强。荆条与藤柳材力学性质的对比表明:荆条各项力学强度指标均高于藤柳材,但荆条弯曲变形、扭曲变形比藤困难,并且荆条韧性优于藤柳、握钉力不如藤。本研究结果为制定"藤及灌木材力学性质测试方法"的国家标准提供理论依据,为荆条加工利用——制作荆编家具提供基础数据。     

大木竹竹材力学性质的研究

在浙江平阳竹木混交林内,采集3年生大木竹,按标准制成试样,测定了丛生竹种大木竹竹材的各力学性质,并以材性优良的毛竹为参比进行分析.结果发现:大木竹竹材的顺纹抗拉、顺纹抗压、抗劈力和抗弯弹性模量分别为238.0 MPa、75.1 MPa、45.6 N·mm-1和12.6 GPa,比毛竹材的相应值大或与毛竹相当,顺纹抗剪和抗弯强度较毛竹材为低.大木竹的各力学性质间有较密切的相关性,顺拉强度:顺压强度:顺剪强度:抗劈力:抗弯强度为3.2:1.0:0.2:0.6:1.8.该研究结果可为大木竹的合理开发利用提供理论依据.     

人工林杉木和杨树木材物理力学性质的株内变异研究

按照中国国家标准研究杉木和I-214杨树木材的抗弯弹性模量、抗弯强度、顺纹抗压强度和密度,同时按照日本国家标准研究2个树种的顺纹抗剪强度.结果表明:杉木的抗弯强度、顺纹抗压强度和密度由胸高直径处向上呈波浪形增加,抗弯弹性模量则稳定降低,但不同高度间杉木的物理力学性质没有显著差异;近树皮处木材的物理力学性质高于近髓心处木材,并有极显著差异.对于I-214杨树,只有抗弯弹性模量从髓心到树皮逐渐增加,其他的物理力学性质,最小值在从髓心到树皮的过渡区,最大值在近树皮处,从髓心到树皮,杨树的物理力学性质有极显著的差异.杉木和杨树的径面顺纹抗剪强度从髓心到树皮有极显著差异,并且近树皮的高于近髓心的木材,而弦面顺纹抗剪强度从髓心到树皮没有显著差异.木材密度与力学性质有很好的线性相关关系,木材密度是一个很好的力学强度的预测手段.     

青海云杉木材物理力学性质试验研究

本文在木材物理力学试验的基础上,研究了青海云杉木材的12种常规物理力学性质,并对个别径、弦平均数进行差异显著性检验,结果表明,青海云杉木材密度轻、干缩小、顺纹抗压强度、抗弯强度、端面硬度很低,抗弯弹性模量和冲击韧性中等,顺纹抗剪强度低,从而为祁连山水源涵养林的综合利用提供了理论依据。     

Estimation of the shear strength of wood by uniaxial-tension tests of off-axis specimens

To determine shear strength we conducted uniaxial-tension tests of off-axis specimens and examined the proper off-axis angles. Sitka spruce (Picea sitchensis Carr.) and katsura (Cercidiphyllum japonicum Sieb. and Zucc.) were used for the studies. Uniaxial tension tests of the specimens with various off-axis angles were conducted, and the shear stress at failure was obtained. Independent of the tension tests, torsion tests were conducted, and the shear strengths were obtained. Comparing the data of the uniaxial tension and torsion tests, we examined the validity of estimating shear strength by the off-axis tension test. The shear strengths obtained from the tension tests coincided well with those measured by the torsion tests when the specimen had an off-axis angle of 15°–30°. In this off-axis angle range, the tensile stress perpendicular to the grain might have a serious influence on the shear strength, and we thought that the shear strength predicted by uniaxial tension tests should be treated as an approximate value despite the simplicity of the tension test. Other test methods should be adopted to obtain the precise shear strength of wood.     

测试方法对毛竹顺纹抗剪强度的影响

以4年生毛竹为对象,分别按照国家标准、行业标准和国际标准的方法,进行顺纹抗剪强度的测试.结果表明:测试方法、试件形状以及加载速度对抗剪强度均有显著影响;行业标准的试件形状能较准确测出竹材的纯抗剪强度,综合测试时间,加载速度以0.8～1.5 mm/min为宜.     

小径柚木异型胶合工艺对集成材胶合性能的影响

以胶合压力、施胶量(单面)、加压时间为影响因素,通过正交试验优化小径柚木胶合工艺,在此基础上研究胶合工艺参数、组合纹理与异型单元件斜边角度对集成材胶合性能的影响。结果表明:优化胶合工艺参数为胶合压力0.7 MPa,施胶量(单面)220 g/m^2,加压时间40 min;胶合压力对胶合剪切强度有显著影响,施胶量(单面)和加压时间对胶合性能影响不显著,随着胶合压力增大,胶合剪切强度随之减小。异型单元件斜边角度和不同纹理组合都对胶合剪切强度有显著影响,对木破率无显著影响。随着梯形组坯单元件斜边角度的增加,胶合剪切强度增加。在弦弦、径弦、径径纹理组合中,弦弦组合纹理胶合剪切强度最大。     

切削参数对木材切削力的影响

为了提供圆锯片合理设计与使用的依据,对水曲柳、杉木和樟子松3种木材进行闭式切削试验,研究锯齿前角、切削厚度、切削速度等参数对切削力的影响规律。结果表明:主切削力和法向切削力均随锯齿前角的增大而减小,随切削厚度的增加而增大,而受切削速度的影响较小。根据试验结果,提出不同密度木材切削参数设置的建议。     

Evaluation of embedding strength on Uruguayan wood to apply the European yield theory for double shear bolted joint

The main objective of this study was to evaluate embedding strength on Uruguayan wood to apply the European yield theory (EYT) for double shear bolted joints’ on Eucalyptus grandis H.(EGH). To introduce the dowel-type connection performance, double shear tests were conducted. The embedding tests were conducted to calculate the yield strength of bolted joint by EYT and the compression test, to estimate the embedding strength. The yield strength obtained from the experiments showed a good agreement with the yield strength calculated by EYT method. The yield strength of double shear bolted joint evaluated from compressive strengths is a very close to the yield strength calculated by EYT. The average value and variability of the yield strength of double shear bolted joint calculated by EYT applying the embedding strengths of experimental results were very close to the yield strength or 5 % offset method of experimental results. The results from this study showed a good behavior to structural design with EGH in accordance to the Japanese standard code.     

Incorporating size effects in the Tsai-Wu strength theory for Douglas-fir laminated veneer

Summary This paper elucidates the need to consider the effect of volume on brittle material strengths when these strengths are used in a strength theory. Specifically, Weibull weakest-link theory has been implemented with the Tsai-Wu strength theory to predict the ultimate load carrying capacity of a center point off-axis bending member made from Douglas-fir laminated veneer. Weibull theory has been used in two distinct ways to account for size effects needed to evaluate brittle material strengths (ie. tension perpendicular and parallel to grain, and shear) for the strength criterion. The analytical methods assume linear elastic, plane stress states and have been described and evaluated using probability theory as a framework. Analytical results are in reasonable agreement with experimental findings substantiating the techniques proposed herein.     

竹展平板拉伸剪切胶合性能

竹展平板是竹筒最大化利用的一种方式,以竹展平板为单元制备竹质人造板可减少胶黏剂使用量,还有利于加工,具有良好的应用前景。然而,竹材是一种天然梯度复合材料,纤维含量在竹壁径向呈现梯度变异,不同纤维含量的胶合面对竹展平板的胶合性能有重要影响。以无刻痕竹展平板为研究对象,参照拉伸剪切强度测试方法,探讨不同纤维含量的竹展平板胶合面在湿态和干态条件下的拉伸剪切强度和破坏方式;同时,分别研究热压压力和施胶量对不同组坯方式下竹展平板胶合性能的影响。结果表明:热压胶合的竹展平板胶合性能主要由基材性能决定,纤维含量较高的竹青?竹青组坯时的拉伸剪切强度高于其他两种组坯方式。基于不同纤维含量基材的干缩湿胀不一致,纤维含量较高的竹青面与纤维含量较低的竹黄面胶合时的湿态拉伸剪切强度保留率最低。竹黄?竹黄组坯时拉伸剪切强度随热压压力的增大而逐渐增加,而竹青?竹青和竹青?竹黄组坯时则先增大后减小。此外,竹黄?竹黄组坯时的干态剪切强度随施胶量的增大而增加。     

15种阔叶树材中切削厚度、刀具前角和木材含水率对切削阻力的影响

１５种阔叶树材切削厚度、刀具前角和木材含水率对切削阻力的影响进行了研究。针叶树材不同树种中此三因素对切削阻力影响的规律，在阔叶树材中有相似表现。在气干到充分吸湿阶段中，含水率对切削阻力影响的趋势在针叶材和阔叶材中有所不同。     

Characterization of strength properties of branchwood and stemwood of some tropical hardwood species

The mechanical strength properties of the branchwood of Aningeria robusta and Terminalia ivorensis with diameters ranging from 10 to 25 cm were examined to determine the suitability of branchwood as raw material for downstream processing. The study precisely assessed the static bending strengths, compression strengths and shear strengths parallel to the grain of the branchwood and stemwood of T. ivorensis and A. robusta. It was observed that under static bending, the overall (sapwood and heartwood combined) modulus of rupture and modulus of elasticity of the branchwood of A. robusta and T. ivorensis were lower than that of their corresponding stemwood. The results further show that the overall compression and shear strengths parallel to the grain of the branchwood of A. robusta and T. ivorensis were higher than that of their corresponding stemwood. Under static bending, compression parallel to the grain, and shear parallel to the grain, the experimental results indicate that the sapwood of the branchwood from both T. ivorensis and A. robusta had lower strength values than that of their corresponding heartwood. Similar results were recorded for the stemwood of T. ivorensis where the heartwood had higher strength values than the sapwood. However, in the case of the stemwood of A. robusta, the sapwood had higher strength values than the corresponding heartwood.     

锯片锯料角对锯切表面粗糙度影响机理分析

分析了锯料角影响锯切表面粗糙度的机理，阐述了锯料角与锯料量对锯切表面粗糙度的影响。分析结果表明，只要锯料角不变化，则锯料量的变化对锯切表面粗糙度不起任何作用。锯料角影响锯切表面粗糙度的机理为开发新型锯片、提高锯切表面的质量和锯切效率提供依据。