Effects of high temperature kiln drying on the practical performances of Japanese cedar wood (Cryptomeria japonica) II: Changes in mechanical properties due to heating

Japanese cedar wood specimens were steamed at 80°, 100°, and 120°C over 14 days, and their equilibrium moisture content (M) at 20°C and 60% relative humidity, longitudinal dynamic Young’s modulus (E), bending strength (σ _max), and breaking strain (ε _max) were compared with those of unheated specimens. Steaming for a longer duration at a higher temperature resulted in a greater reduction in M, σ _max, and ε _max. The E of wood was slightly enhanced by steaming at 100°C for 1–4 days and 120°C for 1–2 days, and thereafter it decreased. The slight increase in the E of sapwood was attributable to the reduction in hygroscopicity, while sufficient explanation was not given for a greater increase in the heartwood stiffness. Irrespective of the steaming temperature, the correlations between M and the mechanical properties of steamed wood were expressed in terms of simple curves. M values above 8% indicated a slight reduction in E and s max, whereas M values below 8% indicated a marked decrease in the mechanical performances. In addition, the e max decreased almost linearly with a decrease in the value of M. These results suggest that hygroscopicity measurement enables the evaluation of degradation in the mechanical performances of wood caused by steaming at high temperatures.     

Thermoplastic flow behavior of steamed wood flour under heat and compression

In this study the thermoplastic flow behavior of steamed wood flour was investigated. First it was demonstrated that steamed Japanese beech flour flowed out of the nozzle under compression at high temperature in a thermal flow test with a capillary rheometer. The effects of the steaming temperature, steaming time, compressive pressure, and moisture content of wood flour on the thermal flow temperature were examined. It was shown that the higher the steaming temperature and compressive pressure, the lower the thermal flow temperature. Also, the thermal flow temperature of the sample steamed at 200°C for 20 min became lowest and increasingly higher over time. Furthermore, the thermal flow temperature became linearly low with increasing moisture content of the sample under 15%, whereas it became essentially constant over 15%. It is clarified that compressive pressure and moisture content as well as the steaming conditions profoundly affect the thermoplastic flow behavior of steamed wood flour.     

Chemical changes of wood during steaming measured by IR spectroscopy

Black locust, poplar and spruce samples were steamed at 80°C and 120°C for 48 hours. IR difference spectra and the CIE Lab colour coordinates were measured for determining the chemical changes caused by the steaming. Steaming at 80°C caused only small changes in both IR spectra and colour. But steaming at 120°C produced intensive colour change and well-visible changes in IR spectra. The guaiacyl lignin in hardwoods underwent slight degradation but in spruce suffered substantial degradation during steaming at 120°C. The syringyl lignin absorbing around 1600 cm^?1 did not show any changes, indicating that it is more stable to steaming than guaiacyl lignin. The absorption decrease at 1175 cm^?1 indicated the cleavage of ether linkage in cellulose and hemicelluloses at both steaming temperatures.     

Compressive deformation of wood impregnated with low molecular weight phenol formaldehyde (PF) resin V: effects of steam pretreatment

This study evaluated the potential of steam pre-treatment for making highly compressed phenol-formaldehyde (PF) resin-impregnated wood at a low pressing pressure. Sawn veneers of Japanese cedar (Cryptomeria japonica) were first subjected to saturated steam at different steaming temperatures (140°-200°C), followed by impregnation with a 20% low molecular weight PF resin aqueous solution resulting in a weight gain of around 50%-55%. Four oven-dried treated veneers were laminated and compressed up to a pressing pressure of 1 MPa at a pressing temperature of 150°C and pressing speed of 5 mm/min, and the pressure was held for 30 min. Steam treatment, causing partial hydrolysis of hemicellulose, accelerated the compressibility of Japanese cedar in the PF resin-swollen condition. As a consequence, a discernible increment in density was achieved at a pressing pressure of 1 MPa due to steam pretreatment between 140° and 200°C for 10 min. It was also found that even a short steaming time such as 2 min at 160°C is sufficient for obtaining appreciable compression of PF resin-impregnated wood. The density, Young’s modulus, and bending strength of steam-treated (200°C for 10 min) PF resin-impregnated wood composite reached 1.09 g/cm³, 20 GPa, and 207MPa, respectively. In contrast, the values of untreated PF resin-impregnated wood composite were 0.87 g/cm³, 13 GPa, and 170MPa, respectively.     

Influence of combined hydro-thermal treatments on selected properties of Turkey oak (Quercus cerris L.) wood

A combined effect of steaming and heat treatment was imposed on green Turkey oak wood, both for sapwood and heartwood. Steaming was carried out in an autoclave at 100–120–130°C whereas heating was carried out in an oven for 2?h at 120–180°C. Equilibrium moisture content at dry, intermediate and moist state both in desorption and adsorption, swelling, cup, twist, color change, and spectral reflectance measures were registered. Swelling and water absorption decreased due to the hydro-thermal treatment. During adsorption, heartwood showed a higher hygroscopic inertia compared to sapwood and this difference increased with temperature. Cup increased with temperature in the steaming process. Twist seemed to be affected more by quality of original trunks than treatments. The wood color was more sensitive at a steaming temperature of 130°C combined with heat treatment at 180°C. Transitional treatments assured more reliable results on homogenization of hue between sapwood and heartwood.     

Thermal-death kinetics of the bark beetle (Dendroctonus armandi; Coleoptera: Scolytidae)

Data on thermal-death kinetics of bark beetles are essential to develop phytosanitary heat treatments for pine wood and pine wood packaging materials. Using a heating block system, effects of different heating rates between 44 and 50°C at 2°C intervals on destruction of Dendroctonus armandi adult insect were examined. Heat resistance of the insects was found to increase at low heating rates (0.1 or 0.5°C/min). Therefore, the thermal-death kinetics of the beetles were determined at a high heating rate of 5.0°C/min which simulated the rapid dielectric heating of wood products. Results showed that the thermal death curve of D. armandi followed a zero-order reaction kinetic model, indicating the heat destruction rate of the beetle at different treatment temperatures to be independent of their population size. The required thermal holding times to result in destruction of the entire population were 40, 8, 4, and 2?min at 44°C, 46°C, 48°C, and 50°C, respectively. The evaluated thermal-death kinetic data are useful in developing effective beetle elimination quarantine protocols for the wood. A 50°C ?2?min heat treatment with a heating rate of ～5°C/min can be effectively used for disinfesting bark wood materials.     

Variation in carbon concentration and wood density for five most commonly grown native tree species in central highlands of Ethiopia: The case of Chilimo dry Afromontane forest

ABSTRACT

Information regarding carbon concentration and wood density are lacking in Chilimo dry Afromontane forest.

The aim of this study was to estimate carbon concentration and wood density for Allophyllus abyssinicus, Olea europaea, Olinia rochetiana, Rhus glutinosa, and Scolopia theifolia. A total of 105, 30–50 mm thick wood discs were collected and oven dried at 102°C and 67°C to constant weight, chopped and finally grinded into 0.2 mm with a grinding mill. Carbon concentration was analyzed using the ash method, while wood density was estimated using the water displacement method. The highest carbon concentration (57.12%) was found for O. rochetiana, however, the lowest carbon concentration (56.43%) was found for A. abyssinicus. Stem parts had higher carbon concentration (56.98%) than branch (56.74%) and leave (54.53%) parts. O. europaea exhibited the highest wood density (0.67 g cm^?3) value than other species. However, the lowest wood density (0.42 g cm^?3) was exhibited for A. abyssinicus. Wood density was also showed a decreasing trend along with increases in stem height and maximum wood density (0.62 g cm^?3) was found under stump position, while, the minimum wood density (0.4 g cm^?3) was found under tree commercial height.     

Yield and mechanical properties of veneer from Brachystegia nigerica

In an effort to find suitable wood from natural forest to meet the demand for veneer products, the yield and tensile strength of veneers produced from Brachystegia nigerica were investigated. Two trees of B. nigerica were separately selected from 10 different natural forest zones while two logs were obtained from each tree. The logs were debarked and steamed in a vat prior to rotary peeling and slicing for veneer production. The optimum steam temperature was determined by considering different temperatures: 50°C, 60°C, 70°C, 80°C and 90°C for 24 h. Thereafter, optimum steam time was determined at the optimum temperature by considering durations of 24, 48, 72 and 96 h. The average taper of 0.75 mm per 1.0 m length was recorded for B. nigerica, indicating that the logs were reasonably cylindrical; thereby its logs are good for the production of veneer. The yield ranged from 44% to 61% with an average of 52% of the log input. The tensile strength of the veneer was tested perpendicular to grain and both peeled and sliced veneers had the highest tensile strength between 70°C and 90°C, suggesting that softening of wood polymers, especially lignin, is between 70°C and 90°C. The optimum temperature and time for veneer production are 70°C and 48 h, respectively. Commercial production of veneer from B. nigerica is feasible based on the yield and mechanical properties of the obtained veneer, thereby encouraging the expansion of the scope ofits utilization.     

Intercalation of wood charcoal with sulfuric acid

Intercalation of wood charcoal with sulfuric acid (H₂SO₄) was investigated. Carbonized sugi (Japanese cedar) samples were prepared by heating at various temperatures in the range 1700°–2700°C. Electrochemical oxidization was carried out in H₂SO₄ and the feasibility of intercalation was determined. In potentiometric analysis, plateaus appeared for samples carbonized at temperatures above 2300°C. In their X-ray diffraction profiles, the peak at around 26° was shifted to a smaller angle of about 22.4°. These results can be considered as signs of intercalation with acid molecules. Fourier transform infrared analysis of charcoal heated at 2700°C, following washing with water and drying of the sample, showed a band at 1220 cm⁻¹ that was assigned to a sulfonate group. This band was not observed for samples heated at 1900°C. These observations suggest the occurrence of intercalation in the former charcoal, but not in the latter. It is concluded that wood charcoal can undergo intercalation when it has ordered stacking of hexagonal carbon layers. Part of this article was presented at the 55th, 56th, and 57th Annual Meetings of the Japan Wood Research Society, Akita, Hiroshima, and Tsukuba, August 2006, August 2007, and March 2008, respectively, and at the International Conference on Carbon “CARBON 2008,” Nagano, July 2008     

Influence of heating history on dynamic viscoelastic properties and dimensions of dry wood

To obtain new information about the mechanical and physical properties of dry wood in unstable states, the influence of heating history on viscoelastic properties and dimensional changes of dry wood in the radial, tangential, and longitudinal directions was studied between 100° and 200°C. Unstable states of dry wood still existed after heating at 105°C for 30 min and were modified by activated molecular motion in the first heating process to temperatures above 105°C. This phenomenon is thought to be caused by the unstable states reappearing after wetting and drying again. Dry wood components did not completely approach the stable state in the temperature range tested, because they did not entirely surpass the glass transition temperatures in most of the temperature range. In constant temperature processes at 135° and 165°C, E′ increased and E″ decreased with time regardless of the direction. This indicated that the unstable states of dry wood components were gradually modified with time at constant temperatures. On the other hand, anisotropy of dimensional change existed and dimension increased in the longitudinal direction, was unchanged in the radial direction, and decreased in the tangential direction with time at constant temperatures. Part of this report was presented at the 13th Annual Meeting of the Chubu Branch of the Japan Wood Research Society, Shizuoka, August 2003     

不同处理方法对杨树木材压缩变形恢复率的研究

采用加热和水蒸气处理方法对人工林杨树木材进行压缩变形恢复率的研究,目的是为了改善人工林软质木材的材性,提高其尺寸稳定性。结果表明:加热和水蒸气处理都是固定人工林木材压缩变形的有效方法;在处理温度相同时,水蒸气处理方法只需要4 min或8 min,而高温加热处理需要10 h或20 h。水蒸气处理方法更加经济。     

Surface quality and hardness of eastern redcedar as function of steaming

The objective of this study was to evaluate influence of steam treatment on surface quality and hardness of eastern redcedar (Juniperus virginiana L.). Defect-free samples with dimensions of 40 mm by 50 mm in by 20 mm were used for the tests. Specimens were exposed to steam having a temperature of 130 °C for 1-h and 3-h periods of time. Surface roughness of the samples at initial and exposed conditions was determined using stylus type equipment across the grain orientation on tangential surface of each sample. Janka hardness of the control and treated samples was also determined on Comten testing system. Based on the findings in this work, no significance was found between surface roughness values of the specimens steamed for 1 and 3 h. However, both types of steamed specimens had higher average roughness values ranging from 52 and 60 % than those of control samples. It appears that 3-h steaming adversely influenced hardness of the samples reducing its 9 % as compared to those of control samples. Densification effect of steaming on the samples was also evaluated using scanning electron microscope (SEM) and it was determined that steaming had some crushing effect on the cell wall.     

Relaxation mechanism of residual stress inside logs by heat treatment: choosing the heating time and temperature

 Some methods to reduce residual stress inside logs have been reported, although the conditions for stress relaxation are not yet clarified. Our study using precise experiments revealed that residual stress relaxation occurs only when both heat and moisture exist inside the logs. We then determined the heating time and temperature required to relax the residual stress inside the logs. Short air-drying treatments did not relax residual stress even though free water in the logs was greatly reduced. The residual stress of the 33-h 80°C-heated bolts was relaxed, whereas that of the 48-h 70°C-heated bolts was not. As for the influence of treatment time, bolts heated at 100°C were relaxed after 18 h of treatment. The 13-h heated bolts did not show any relaxation. Therefore, residual stress relaxation occurred rapidly owing to the thermomechanical change of the individual wood components comprising the cell wall. The moisture content inside all the bolts was much higher than the fiber saturation point. This is because relaxation occurs only when the heating temperature is maintained above 80°C for a particular duration of treatment. Received: December 12, 2001 / Accepted: February 18, 2002 Present address: Institute for Structural and Engineering Materials, National Institute of Advanced Industrial Sciences and Technology, Independent Administrative Institution, Nagoya 463-8560, Japan Tel. +81-52-736-7320; Fax +81-52-736-7419 e-mail: m.nogi@aist.go.jp Part of this report was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, April 2000 Correspondence to:M. Nogi     

Effect of wood species on thermal flow behavior and physical properties of thermoplastic moldings

The thermoplastic flow behavior of cedar flour steamed at different temperatures in the range of 160–220°C was measured using a rheometer and compared with that of beech flour. The temperature at which the cedar flour starts to flow was approximately 70°C higher than that of beech flour, and the cedar flour exhibited low flowability. Furthermore, thermoplastic moldings were prepared from cedar and beech flours, and their physical properties were examined. Similar to the case of beech, a resin-like molding with a density of approximately 1.45?g/cm³ was obtained from the cedar flour steamed at 180°C or higher, and it was revealed by SEM observation that in these moldings wood flour particles adhere to each other. The specific bending strength was maximum for the moldings obtained from 180°C-steamed flour for both types of wood.     

Evaluation of the temperature and relative humidity preferences of the western dry-wood termite <Emphasis Type="Italic">Incisitermes minor</Emphasis> (Hagen) using acoustic emission (AE) monitoring

Twenty-four different combinations of six temperatures (15°, 20°, 25°, 30°, 35°, and 40°C) and four relative humidity (RH) (60%, 70%, 80%, and 90%) conditions were used for pseudergates of the western dry-wood termite Incisitermes minor (Hagen). The feeding activities of the termites were monitored by the detection of generated acoustic emission (AE) events from feeder wood blocks in a test chamber. Temperature and RH showed independent and interactive significant effects on the feeding activity of I. minor. The optimal temperature and RH conditions for the feeding activities were 35°C and 70%, respectively, and the optimal combinations were 35°C-70% and 35°C-80% with an exceptionally higher feeding activity at the combination condition of 30°C-70%.     

Influence of steam heating on the properties of pine (<Emphasis Type="Italic">Pinus pinaster</Emphasis>) and eucalypt (<Emphasis Type="Italic">Eucalyptus globulus</Emphasis>) wood

Heat treatment of Pinus pinaster and Eucalyptus globulus woods, two important species in Portugal, was performed in the absence of air by steaming, inside an autoclave, for 2–12 h at 190–210°C. Mass losses increased with treatment time and temperature reaching 7.3% for pine and 14.5% for eucalypt wood. The wood behaviour with moisture was improved. The equilibrium moisture content decreased by 46% for pine and 61% for eucalypt, the dimensional stability increased (maximum anti-shrinking efficiency in the radial direction of 57 and 90% for pine and eucalypt, respectively) and the surface wettability was lowered. In relation to mechanical properties, the modulus of elasticity was little affected (maximum decrease of 5% for pine and 15% for eucalypt) but the bending strength was reduced (by 40% at 8% mass loss for pine and 50% at 9% mass loss for eucalypt wood). The variation of properties was related to treatment intensity and mass loss but significant improvements could already be obtained for a 3–4% mass loss without impairing the mechanical resistance. The response of eucalypt was higher than that of pinewood. Heat treatment of eucalypt wood shows an interesting potential to improve the wood quality for solid timber products.     

Real-time measurement of vibrational properties and fine structural properties of wood at high temperature

Vibrational properties and fine structural properties of wood were measured at high temperatures. Sitka spruce (Picea sitchensis Carr.) and Shioji (Japanese ash, Fraxinus spaethiana Lingelsh.) were used as specimens. The specimens, the system to support them, a magnetic driver, and a deflection sensor were in an electric drying oven, where vibration tests were conducted. The heating temperatures ranged from room temperature to 200 °C in 25 °C increments in both heating and cooling processes. X-ray diffractometry was carried out using positive sensitive proportional counter (PSPC) at room temperature to 200 °C in 20 °C increments in both heating and cooling processes. Received 13 December 1999     

High-temperature mechanical properties and thermal recovery of balsa wood

This article presents an experimental study into thermal softening and thermal recovery of the compression strength properties of structural balsa wood (Ochroma pyramidale). Balsa is a core material used in sandwich composite structures for applications where fire is an ever-present risk, such as ships and buildings. This article investigates the thermal softening response of balsa with increasing temperature, and the thermal recovery behavior when softened balsa is cooled following heating. Exposure to elevated temperatures was limited to a short time (15 min), representative of a fire or postfire scenario. The compression strength of balsa decreased progressively with increasing temperature from 20° to 250°C. The degradation rates in the strength properties over this temperature range were similar in the axial and radial directions of the balsa grains. Thermogravimetric analysis revealed only small mass losses (<2%) in this temperature range. Environmental scanning electron microscopy showed minor physical changes to the wood grain structure from 190° to 250°C, with holes beginning to form in the cell wall at 250°C. The reduction in compression properties is attributed mostly to thermal viscous softening of the hemicellulose and lignin in the cell walls. Post-heating tests revealed that thermal softening up to 250°C is fully reversible when balsa is cooled to room temperature. When balsa is heated to 250°C or higher, the post-heating strength properties are reduced significantly by decomposition processes of all wood constituents, which irreversibly degrade the wood microstructure. This study revealed that the balsa core in sandwich composite structures must remain below 200°–250°C when exposed to fire to avoid permanent heat damage.     

Effects of heat treatment on brittleness of <Emphasis Type="Italic">Styrax tonkinensis</Emphasis> wood

A new approach is proposed for the evaluation of the brittleness of heat-treated Styrax tonkinensis wood. Heat treatment made wood more brittle when wood was heated at a higher temperature or for a longer time. The brittleness increased to four times that of the control when wood was heated at 200°C for 12 h. For treatment at 160°C, the increase in brittleness without any change in weight is thought to be possibly caused by the relocation of lignin molecules. At higher temperatures, loss of amorphous polysaccharides due to degradation is thought to become the main factor affecting brittleness. The crystallites that were newly formed after 2 h of treatment showed brittleness that was different from that of the inherent crystallites remaining after 12 h of heat treatment. This inherent crystalline cellulose possibly plays a role in brittleness. There is also the possibility of using color to predict the brittleness of heat-treated wood.     

Changes of decay and termite durabilities of Japanese larch (Larix leptolepis) wood due to high-temperature kiln drying processes

We investigated the effects of high-temperature drying schedules (120°–130°C) on decay and termite feeding of Japanese larch timbers. Thermogravimetric analysis was conducted to investigate changes of the wood components. Decay and termite feeding tests showed that specimens dried under high-temperature schedules were susceptible against a decaying fungus Fomitopsis palustris and attacks from termites Coptotermes formosanus and Reticulitermes speratus. These drying schedules changed chemical components, which were suggested by the thermal analytical result compared to the control sample. The results of this study indicated that the acceleration of termite feeding takes place even under temperatures that are comparatively lower than that used in our previous research in which 170°C steaming treatment was applied to Japanese larch wood. Decay durability against a brown rot fungus also decreased, possibly from production of low molecular weight fragments when hemicellulose decreased during the high-temperature drying processes.