Impact of preferential interactions on thermal stability and gelation of bovine serum albumin in aqueous sucrose solutions

The influence of sucrose (0--40 wt %) on the thermal denaturation and gelation of bovine serum albumin (BSA) in aqueous solution has been studied. The effect of sucrose on heat denaturation of 1 wt % BSA solutions (pH 6.9) was measured using ultrasensitive differential scanning calorimetry. The unfolding process was irreversible and could be characterized by a denaturation temperature (T(m)), activation energy (E(A)), and pre-exponential factor (A). As the sucrose concentration increased from 0 to 40 wt %, T(m) increased from 72.9 to 79.2 degrees C, E(A) decreased from 314 to 289 kJ mol(-1), and ln(A/s(-1)) decreased from 104 to 94. The rise in T(m) was attributed to the increased thermal stability of the globular state of BSA relative to its native state because of differences in their preferential interactions with sucrose. The change in preferential interaction coefficient (Delta Gamma(3,2)) associated with the native-to-denatured transition was estimated. The dynamic shear rheology of 2 wt % BSA solutions (pH 6.9, 100 mM NaCl) was monitored as they were heated from 30 to 90 degrees C, held at 90 degrees C for either 15 or 120 min, and then cooled to 30 degrees C. Sucrose increased the gelation temperature due to thermal stabilization of the native state of the protein. The complex shear modulus (G) of cooled gels decreased with sucrose concentration when they were held at 90 degrees C for 15 min because the fraction of irreversibly denatured protein decreased. On the other hand, G of cooled gels increased with sucrose concentration when they were held at 90 degrees C for 120 min because a greater fraction of irreversibly denatured protein was formed and the strength of the protein-protein interactions increased.     

Combined influence of NaCl and sucrose on heat-induced gelation of bovine serum albumin

The combined influence of a strongly interacting cosolvent (NaCl) and a weakly interacting cosolvent (sucrose) on the heat-induced gelation of bovine serum albumin (BSA) was studied. The dynamic shear rheology of 4 wt % BSA solutions containing 0 or 20 wt % sucrose and 0-200 mM NaCl was monitored as they were heated from 30 to 90 degrees C at 1.5 degrees C min(-)(1), held at 90 degrees C for 120 min, and then cooled back to 30 degrees C at -1.5 degrees C min(-)(1). The turbidity of the same solutions was monitored as they were heated from 30 to 95 degrees C at 1.5 degrees C min(-)(1) or held isothermally at 90 degrees C for 10 min. NaCl had a similar effect on BSA solutions that contained 0 or 20 wt % sucrose, with the gelation temperature decreasing and the final gel strength increasing with increasing salt concentration and the greatest changes occurring between 25 and 100 mM NaCl. Nevertheless, the presence of sucrose did lead to an increase in the gelation temperature and final gel strength and a decrease in the final gel turbidity. The impact of NaCl on gel characteristics was attributed primarily to its ability to screen electrostatic interactions between charged protein surfaces, whereas the impact of sucrose was attributed mainly to its ability to increase protein thermal stability and strengthen the attractive forces between proteins through a preferential interaction mechanism.     

Influence of sucrose on droplet flocculation in hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin

The influence of sucrose on the flocculation stability of hydrocarbon oil-in-water emulsions stabilized by a globular protein was examined using laser diffraction. Salt (150 mM NaCl) and sucrose (0-40 wt %) were added to n-hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin (beta-Lg, pH 7.0) either before or after isothermal heat treatment (30-95 degrees C for 20 min). When salt was added to emulsions before heat treatment, appreciable droplet flocculation was observed below the thermal denaturation temperature of the adsorbed beta-Lg (T(m) approximately 70 degrees C), and more extensive flocculation was observed above T(m). On the other hand, when salt was added to emulsions after heat treatment, appreciable droplet flocculation still occurred below T(m), but little flocculation was observed above T(m). Addition of sucrose to the emulsions increased T(m) and either promoted or suppressed droplet flocculation depending on whether it was added before or after heat treatment. These results are interpreted in terms of the influence of sucrose on protein conformational stability, protein-protein interactions, and the physiochemical properties of aqueous solutions. This study has important implications for the formulation and production of protein stabilized oil-in-water emulsions.     

Properties and stability of oil-in-water emulsions stabilized by coconut skim milk proteins

Protein fractions were isolated from coconut: coconut skim milk protein isolate (CSPI) and coconut skim milk protein concentrate (CSPC). The ability of these proteins to form and stabilize oil-in-water emulsions was compared with that of whey protein isolate (WPI). The solubility of the proteins in CSPI, CSPC, and WPI was determined in aqueous solutions containing 0, 100, and 200 mM NaCl from pH 3 to 8. In the absence of salt, the minimum protein solubility occurred between pH 4 and 5 for CSPI and CSPC and around pH 5 for WPI. In the presence of salt (100 and 200 mM NaCl), all proteins had a higher solubility than in distilled water. Corn oil-in-water emulsions (10 wt %) with relatively small droplet diameters (d32 approximately 0.46, 1.0, and 0.5 mum for CSPI, CSPC, and WPI, respectively) could be produced using 0.2 wt % protein fraction. Emulsions were prepared with different pH values (3-8), salt concentrations (0-500 mM NaCl), and thermal treatments (30-90 degrees C for 30 min), and the mean particle diameter, particle size distribution, zeta-potential, and creaming stability were measured. Considerable droplet flocculation occurred in the emulsions near the isoelectric point of the proteins: CSPI, pH approximately 4.0; CSPC, pH approximately 4.5; WPI, pH approximately 4.8. Emulsions with monomodal particle size distributions, small mean droplet diameters, and good creaming stability could be produced at pH 7 for CSPI and WPI, whereas CSPC produced bimodal distributions. The CSPI and WPI emulsions remained relatively stable to droplet aggregation and creaming at NaCl concentrations of < or =50 and < or =100 mM, respectively. In the absence salt, the CSPI and WPI emulsions were also stable to thermal treatments at < or =80 and < or =90 degrees C for 30 min, respectively. These results suggest that CSPI may be suitable for use as an emulsifier in the food industry.     

Control of heat-induced aggregation of whey proteins using casein

The ability of alphas1/beta-casein and micellar casein to protect whey proteins from heat-induced aggregation/precipitation reactions and therefore control their functional behavior was examined. Complete suppression (>99%) of heat-induced aggregation of 0.5% (w/w) whey protein isolate (pH 6.0, 85 degrees C, 10 min) was achieved at a ratio of 1:0.1 (w/w) of whey protein isolate (WPI) to alphas1/beta-casein, giving an effective molar ratio of 1:0.15, at 50% whey protein denaturation. However, in the presence of 100 mM NaCl, heating of the WPI/alphas1/beta-casein dispersions to 85 degrees C for 10 min resulted in precipitation between pH 6 and 5.35. WPI heated with micellar casein in simulated milk ultrafiltrate was stable to precipitation at pH>5.4. Protein particle size and turbidity significantly (P相似文献   

Impact of protein surface denaturation on droplet flocculation in hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin

The influence of globular protein denaturation after adsorption to the surface of hydrocarbon droplets on flocculation in oil-in-water emulsions was examined. n-Hexadecane oil-in-water emulsions (pH 7.0) stabilized by beta-lactoglobulin (1-wt % beta-Lg) were prepared by high-pressure valve homogenization. NaCl (0-150 mM) was added to these emulsions immediately after homogenization, and the evolution of the mean particle diameter (d) and particle size distribution (PSD) was measured by laser diffraction during storage at 30 degrees C for 48 h. No change in d or PSD was observed in the absence of added salt, which indicated that these emulsions were stable to flocculation. When 150 mM NaCl was added to emulsions immediately after homogenization, d increased rapidly during the following few hours until it reached a plateau value, while the PSD changed from monomodal to bimodal. Addition of N-ethylmaleimide, a sulfhydryl blocking agent, to the emulsions immediately after homogenization prevented (at 20 mM NaCl) or appreciably retarded (at 150 mM NaCl) droplet flocculation. These data suggests that protein unfolding occurred at the droplet interface, which increased the hydrophobic attraction and disulfide bond formation between droplets. In the absence of added salt, the electrostatic repulsion between droplets was sufficient to prevent flocculation, but in the presence of sufficient salt, the attractive interactions dominated, and flocculation occurred.     

Gelling properties of heat-denatured beta-lactoglobulin aggregates in a high-salt buffer

Thermal denaturation, rheological, and microstructural properties of gels prepared from native beta-lactoglobulin (beta-LG) and preheated or heat-denatured beta-LG (HDLG) aggregates were compared. The HDLG was prepared by heating solutions of 4% beta-LG in deionized water, pH 7.0, at 80 degrees C for 30 min and then diluted to the desired concentration in 0.6 M NaCl and 0.05 M phosphate buffer at pH 6.0, 6.5, and 7.0. When reheated to 71 degrees C, HDLG formed a gel at a concentration of 2% protein. At pH 7.0, 3% HDLG gelled at 52.5 degrees C and had a storage modulus (G') of 2200 Pa after cooling. beta-LG (3%) in 0.6 M NaCl and 0.05 M phosphate buffer, pH 7.0, did not gel when heated to 71 degrees C. The gel point of 3% HDLG decreased by 10.5 degrees C and the G' did not change when the pH was decreased to 6.0. The HDLG gel microstructure was composed of strands and clumps of small globular aggregates in contrast to beta-LG gels, which contained a particulate network of compacted globules. The HDLG formed a gel at a lower concentration and lower temperature than beta-LG in the high-salt buffer, suggesting an application in meat systems or other food products prepared with salt and processed at temperatures of < or =71 degrees C.     

Stabilization of oil-in-water emulsions by cod protein extracts

The ability of two protein fractions extracted from cod to form and stabilize oil-in-water emulsions was examined: a high salt extracted fraction (HSE protein) and a pH 3 acid extracted fraction (AE protein). Both fractions consisted of a complex mixture of different proteins, with the predominant one being myosin (200 kDa). The two protein fractions were used to prepare 5 wt % corn oil-in-water emulsions at ambient temperature (pH 3.0, 10 mM citrate-imidazole buffer). Emulsions with relatively small mean droplet diameters (d(3,2) < 1 microm) and good creaming stability (> 9 days) could be produced at protein concentrations > or =0.2 wt % for both fractions. The isoelectric point of droplets stabilized by both protein fractions was pH approximately 5. The emulsions were stable to droplet flocculation and creaming at relatively low pH (< or =4) and NaCl concentrations (< or =150 mM) when stored at room temperature. In the absence of salt, the emulsions were also stable to thermal treatment (30-90 degrees C for 30 min), but in the presence of 100 mM NaCl droplet flocculation and creaming were observed in some of the emulsions, particularly those stabilized by the AE fraction. The results suggest that protein fractions extracted from cod can be used as emulsifiers to form and stabilize food emulsions.     

Heat-induced gelation of chicken Pectoralis major myosin and beta-lactoglobulin

The denaturation, aggregation, and rheological properties of chicken breast muscle myosin, beta-lactoglobulin (beta-LG), and mixed myosin/beta-LG solutions were studied in 0.6 M NaCl, 0.05 mM sodium phosphate buffer, pH 7.0, during heating. The endotherm of a mixture of myosin and beta-LG was identical to that expected if the endotherm of each protein was overlaid on the same axis. The maximum aggregation rate (AR(max)) increased, and the temperature at the AR(max) (T(max)) and initial aggregation temperature (T(o)) decreased as the concentration of both proteins was increased. The aggregation profile of <0.5% myosin was altered by the presence of 0.25% beta-LG. Addition of 0.5-3.0% beta-LG decreased storage moduli of 1% myosin between 55 and 75 degrees C, but increased storage moduli (G') when heated to 90 degrees C and after cooling. beta-LG had no effect on the gel point of > or =1.0% myosin, but enhanced gel strength when heated to 90 degrees C and after cooling. After cooling, the G' of 1% myosin/2%beta-LG gels was about 1.7 times greater than that of gels prepared from 2% myosin/1% beta-LG.     

Effects of pH and the gel state on the mechanical properties, moisture contents, and glass transition temperatures of whey protein films.

The mechanical properties, moisture contents (MC), and glass transition temperature (T(g)) of whey protein isolate (WPI) films were studied at various pH values using sorbitol (S) as a plasticizer. The films were cast from heated aqueous solutions and dried in a climate chamber at 23 degrees C and 50% relative humidity (RH) for 16 h. The critical gel concentrations (c(g)) for the cooled aqueous solutions were found to be 11.7, 12.1, and 11.3% (w/w) WPI for pH 7, 8, and 9, respectively. The cooling rate influenced the c(g), in that a lower amount of WPI was needed for gelation when a slower cooling rate was applied. Both cooling rates used in this study showed a maximum in the c(g) at pH 8. The influence of the polymer network on the film properties was elucidated by varying the concentration of WPI over and under the c(g). Strain at break (epsilon(b)) showed a maximum at the c(g) for all pH values, thus implying that the most favorable structure regarding the ability of the films to stretch is formed at this concentration. Young's modulus (E) and stress at break (sigma(b)) showed a maximum at c(g) for pH 7 and 8. The MC and epsilon(b) increased when pH increased from 7 to 9, whereas T(g) decreased. Hence, T(g) values were -17, -18, and -21 degrees C for pH 7, 8, and 9, respectively. E and sigma(b) decreased and epsilon(b) and thickness increased when the surrounding RH increased. The thickness of the WPI films also increased with the concentration of WPI.     

Protein-stabilized nanoemulsions and emulsions: comparison of physicochemical stability, lipid oxidation, and lipase digestibility

The properties of whey protein isolate (WPI) stabilized oil-in-water (O/W) nanoemulsions (d(43) ≈ 66 nm; 0.5% oil, 0.9% WPI) and emulsions (d(43) ≈ 325 nm; 0.5% oil, 0.045% WPI) were compared. Emulsions were prepared by high-pressure homogenization, while nanoemulsions were prepared by high-pressure homogenization and solvent (ethyl acetate) evaporation. The effects of pH, ionic strength (0-500 mM NaCl), thermal treatment (30-90 °C), and freezing/thawing on the stability and properties of the nanoemulsions and emulsions were compared. In general, nanoemulsions had better stability to droplet aggregation and creaming than emulsions. The nanoemulsions were unstable to droplet flocculation near the isoelectric point of WPI but remained stable at higher or lower pH values. In addition, the nanoemulsions were stable to salt addition, thermal treatment, and freezing/thawing (pH 7). Lipid oxidation was faster in nanoemulsions than emulsions, which was attributed to the increased surface area. Lipase digestibility of lipids was slower in nanoemulsions than emulsions, which was attributed to changes in interfacial structure and protein content. These results have important consequences for the design and utilization of food-grade nanoemulsions.     

Heat inactivation and reactivation of broccoli peroxidase

Heat inactivation characteristics differed for acidic (A), neutral (N), and basic (B) broccoli peroxidase. At 65 degrees C, A was the most heat stable followed by N and B. The activation energies for denaturation were 388, 189, and 269 kJ/mol for A, N, and B, respectively. Reactivation of N occurred rapidly, within 10 min after the heated enzyme was cooled and incubated at room temperature. The extent of reactivation varied from 0 to 50% depending on the isoenzyme and heating conditions (temperature and time). The denaturation temperature allowing the maximum reactivation was 90 degrees C for A and horseradish peroxidase (HRP) and 70 and 80 degrees C for B and N, respectively. In all cases, heat treatment at low temperatures for long times prevented reactivation of the heated enzymes. Calcium (5 mM) increased the thermal stability of N and B but had no effect on reactivation. The presence of 0.05% bovine serum albumin decreased thermal stability but increased the extent of reactivation of A..     

Heat-induced changes in the ultrasonic properties of whey proteins

The physical aggregation of commercial whey protein isolate (WPI) and purified beta-lactoglobulin was studied by ultrasound spectroscopy. Protein samples were dialyzed to achieve constant ionic strength backgrounds of 0.01 and 0.1 NaCl, and gelation was induced in situ at constant temperatures (from 50 to 75 degrees C) or with a temperature ramp from 20 to 85 degrees C. Changes in the ultrasonic properties were shown in the early stages of heating, at temperatures below those reported for protein denaturation. During heating, the relative ultrasound velocity (defined as the difference between sample velocity and reference velocity) decreased continuously with temperature, indicating a rearrangement of the hydration layer of the protein and an increase in compressibility of the protein shell. At temperatures <50 degrees C the ultrasonic attenuation decreased, and <65 degrees C both velocity and attenuation differentials showed increasing values. A sharp decrease in the relative velocity and an increase in the attenuation at 70 degrees C were indications of "classical" protein denaturation and the formation of a gel network. Values of attenuation were significantly different between samples prepared with 0.01 and 0.1 M NaCl, although no difference was shown in the overall ultrasonic behavior. WPI and beta-lactoglobulin showed similar ultrasonic properties during heating, but some differences were noted in the values of attenuation of WPI solutions, which may relate to a less homogeneous distribution of aggregates caused by the presence of alpha-lactalbumin and other minor proteins in WPI.     

Influence of EDTA and citrate on physicochemical properties of whey protein-stabilized oil-in-water emulsions containing CaCl2

The influence of chelating agents (disodium ethylenediaminetetraacetate (EDTA) and sodium citrate) on the physicochemical properties of whey protein isolate (WPI)-stabilized oil-in-water emulsions containing calcium chloride was determined. The calcium-binding characteristics of EDTA and citrate at 30 degrees C were characterized in aqueous solutions (20 mM Tris buffer, pH 7.0) by isothermal titration calorimetry (ITC). EDTA and citrate both bound calcium ions in a 1:1 ratio, but EDTA had a much higher binding constant. Oil-in-water emulsions (pH 7.0) were prepared containing 6.94% (w/v) soybean oil, 0.35% (w/v) WPI, 0.02% (w/v) sodium azide, 20 mM Tris buffer, 10 mM CaCl(2), and 0-40 mM chelating agent. The particle size, apparent viscosity, creaming stability, free calcium concentration, and particle surface potential of the emulsions were measured. The chelating agents reduced or prevented droplet aggregation in the emulsions. When they were present above a certain concentration (>3.5 mM EDTA or >5 mM citrate), droplet aggregation was prevented. The reduction of aggregation was indicated by decreases in particle size, shear-thinning behavior, apparent viscosity, and creaming. Emulsions containing chelating agents had lower free calcium concentrations and more negatively charged droplets, indicating that the chelating agents improved emulsion stability by binding calcium ions. EDTA could be used at lower concentrations than citrate because of its higher calcium ion binding constant.     

Aging of whey protein films and the effect on mechanical and barrier properties

This work focuses on the aging of whey protein isolate (WPI) films plasticized with glycerol (G) and sorbitol (S). The films were cast from heated aqueous solutions at pH 7 and dried at 23 degrees C and 50% relative humidity (RH) for 16 h. They were stored in a climate room (23 degrees C, 50% RH) for 120 days, and the film properties were measured at regular intervals. The moisture content (MC) of the WPI/G films decreased from 22% (2 days) to 15% (45 days) and was thereafter constant at 15% (up to 120 days). This affected the mechanical properties and caused an increased stress at break (from 2.7 to 8.3 MPa), a decreased strain at break (from 33 to 4%), and an increased glass transition temperature (T(g)) (from -56 to -45 degrees C). The barrier properties were, however, unaffected, with constant water vapor permeability and a uniform film thickness. The MC of the WPI/S films was constant at approximately 9%, which gave no change in film properties.     

Formation of whey protein isolate (WPI)-dextran conjugates in aqueous solutions

The conjugation reaction between whey protein isolate (WPI) and dextran in aqueous solutions via the initial stage of the Maillard reaction was studied. The covalent attachment of dextran to WPI was confirmed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) with both protein and carbohydrate staining. The formation of WPI-dextran conjugates was monitored by a maximum absorbance peak at approximately 304 nm using difference UV spectroscopy. The impact of various processing conditions on the formation of WPI-dextran conjugates was investigated. The conjugation reaction was promoted by raising the temperature from 40 to 60 degrees C, the WPI concentration from 2.5 to 10%, and the dextran concentration from 10 to 30% and lowering the pH from 8.5 to 6.5. The optimal conjugation conditions chosen from the experiments were 10% WPI-30% dextran and pH 6.5 at 60 degrees C for 24 h. WPI-dextran conjugates were stable under the conditions studied.     

Maltodextrin-anionic surfactant interactions: isothermal titration calorimetry and surface tension study

Interactions between maltodextrin (DE = 10) and an anionic surfactant (sodium dodecyl sulfate, SDS) were studied in a buffer solution (pH 7.0, 10 mM NaCl, 20 mM Trizma, 30.0 degrees C) using isothermal titration calorimetry (ITC), surface tension, differential scanning calorimetry (DSC), and turbidity techniques. ITC measurements indicated that the binding of SDS to maltodextrin was exothermic and that, on average, one SDS monomer bound per 24 glucose units of maltodextrin at saturation. Surface tension measurements indicated that there was a critical surfactant concentration ( approximately 0.05 mM SDS) below which surfactant and maltodextrin did not interact and that the amount of surfactant bound to the maltodextrin above this concentration increased with increasing maltodextrin concentration. Turbidity measurements indicated that the solutions remained transparent at all maltodextrin (0-1 wt %) and SDS (0-20 mM) concentrations studied, which suggested that phase separation did not occur. DSC measurements indicated that no phase transitions occurred between 10 and 110 degrees C for maltodextrin solutions (0.5 wt %) in the presence or absence of surfactant. A phase diagram was developed to describe the interactions between SDS and maltodextrin.     

Gelation of chicken pectoralis major myosin and heat-denatured beta-lactoglobulin

Thermal, rheological, and microstructural properties of myosin (1 and 2% protein) were compared to mixtures of 1% myosin and 1% heat-denatured beta-lactoglobulin aggregates (myosin/HDLG) and 1% myosin and 1% native beta-lactoglobulin (myosin/beta-LG) in 0.6 M NaCl and 0.05 M sodium phosphate buffer, pH 6.0, 6.5, and 7.0 during heating to 71 degrees C. Thermal denaturation patterns of myosin and myosin/HDLG were similar except for the appearance of an endothermic peak at 54-56 degrees C in the mixed system. At pH 7.0, 2% myosin began to gel at 48 degrees C and had a storage modulus (G') of 500 Pa upon cooling. Myosin/HDLG (2% total protein) had a gel point of 48 degrees C and a G' of 650 Pa, whereas myosin/beta-LG had a gel point of 49 degrees C but the G' was lower (180 Pa). As the pH was decreased, the gel points of myosin and myosin/HDLG decreased and the G' after cooling increased. The HDLG was incorporated within the myosin gel network, whereas beta-LG remained soluble.     

Conformational states of sunflower (Helianthus annuus) Helianthinin: effect of heat and pH

The structure and solubility of helianthinin, the most abundant protein of sunflower seeds, was investigated as a function of pH and temperature. Dissociation of the 11S form (hexamer) into the 7S form (trimer) gradually increased with increasing pH from 5.8 to 9.0. High ionic strength (I = 250 mM) stabilizes the 11S form at pH > 7.0. Heating and low pH resulted in dissociation into the monomeric constituents (2-3S). Next, the 7S and 11S forms of helianthinin were isolated and shown to differ in their secondary and tertiary structure, and to have denaturation temperatures (T(d)) of 65 and 90 degrees C, respectively. Furthermore, the existence of two populations of the monomeric form of helianthinin with denaturation temperatures of 65 and 90 degrees C was described. This leads to the hypothesis that helianthinin can adopt two different conformational states: one with T(d) = 65 degrees C and a second with T(d) = 90 degrees C.     

Phosphorylation of egg white proteins by dry-heating in the presence of phosphate

Food proteins were phosphorylated by heating in a dry state in the presence of phosphate. When casein, whey protein isolate (WPI), and egg white proteins (EWP), which were lyophilized from their solutions in a phosphate buffer, were dry-heated at various temperatures and pH levels for 1-5 days, EWP was more highly phosphorylated than casein and WPI. Phosphorylation of EWP was promoted with a decrease of pH from 7.0 to 3.0 when the incubation temperature was raised from 55 to 100 degrees C. The phosphorus content of EWP increased from 0.08 to 0.64% by dry-heating at pH 3.0 and 85 degrees C for 5 days in the presence of phosphate. The electrophoretic mobility of EWP increased with an increase in the phosphorylation level. The heat-induced polymerization of EWP by dry-heating was not affected by the presence of phosphate. Although the solubility of EWP decreased by dry-heating at pH 3.0-5.5, the phosphorylation depressed the insolubilization at low pH. The phosphate bonds in phosphorylated EWP (P-EWP) were stable at pH 2.0-10.0 and were more acid-labile and base-stable than phosphoesters of egg riboflavin-binding protein (RfBP). (31)P NMR spectral data suggested that besides phosphoesters, phosphodiester and polyphosphate bonds were introduced in P-EWP. Heat stability of EWP was improved, and calcium phosphate-solubilizing ability of EWP was enhanced by phosphorylation.