Sound absorption property of wood for five eucalypt species

The sound absorption coefficients of wood and wood boards for five eucalypt species (Eucalyptus urophylla, Eucalyptus urophylla x E. grandis, Eucalyptus urophylla x E. tereticornis, Eucalyptus urophylla x E. camaldulensis and Eucalyptus cloeziana) that were collected from plantation in Dongmen Forestry Center of Guangxi Province, China were tested with standing wave method and their sound absorption properties were also compared. The results showed that the sound absorption coefficients of the five eucalypt wood species did not change evidently below 1000 Hz, but above 1000 Hz their sound absorption coefficients increased with the increasing frequency. The difference in sound absorption coefficient among five species of eucalypt wood is not evident at the tested frequency range (200–2000 Hz), but the sound absorption property ofEucalyptus urophylla at low frequency is better than that of other four species. The sound absorption coefficient of the tangential-sawn board is higher than that of the radial-sawn board. The sound absorption property of eucalypt wood of 0.5 cm in thickness is much better than that of 1.0 cm in thickness. It is concluded that wood sound absorption properties of eucalypts are affected by their board thickness and the type of sawn timber within the testing frequency, but the variance of wood sound absorption property among the five tested species is not significant. Fundation item This study is Part of 2000-4-13 in “948” Project from the State Forestry Administration of P.R. China Biography: JIANG Ze-hui (1939-), female, Professor in Research Institute of Wood Industry in Chinese Academy of Forestry. Responsible editor: Chai Ruihai     

Detection of incipient decay in tree stems with sonic tomography after wounding and fungal inoculation

Picus^® acoustic tomography was used to map incipient stages of fungal decay in the sapwood of standing Douglas fir, beech, oak, and sycamore trees 2, 16, and 27 months after wounding and artificial inoculation with brown-, soft-, and white-rot decay fungi. Some wood properties were additionally measured before (velocity of sound) and after (moisture content, weight loss, and density of sound, discoloured and/or decayed wood) tree felling (28 months). With the exception of Trametes versicolor in sycamore, wood decay was not evident from the tomograms in any host-fungus combination. In comparison to measurements after two months, the device recorded a reduction in sound velocity in some host-fungus combinations after 16 and 27 months. In beech, there was a significant reduction in sound velocity after inoculation with Ganoderma applanatum, Kretzschmaria deusta, and Trametes versicolor. Similarly, a reduction in sound velocity was recorded in sycamore inoculated with Kretzschmaria deusta and Trametes versicolor. In all these combinations, losses in wood weight and wood density were also found. Results showed that the detection of incipient fungal decay at the periphery of tree stems needs to be improved such that tomograms of the Picus^® acoustic tomograph are capable of identifying decay progressing from the sapwood inwards.     

Analysis of the water vapour sorption isotherms of thermally modified acacia and sesendok

Abstract

Two Malaysian hardwoods, acacia (Acacia mangium) and sesendok (Endospermum malaccense), that had been subjected to oleo-thermal modification were studied to determine their sorption isotherm behaviour using a dynamic vapour sorption apparatus. All the specimens were thermally modified using palm oil at three different temperatures (180, 200 and 220°C) and three different times (1, 2 and 3 h). The results showed that there was a reduction in equilibrium moisture content at each target relative humidity due to the heat treatment, but that the two wood species showed different behaviour in this respect. The adsorption isotherms were analysed using the Hailwood and Horrobin model, with excellent fits to the experimental data. The monolayer water and polylayer water were both reduced at a range of relative humidity values of the treated samples, although behaviour between the two wood species differed. Heat treatment resulted in an increase in hysteresis ratio, which was probably due to the increase in matrix stiffness of the cell walls.     

Finger-jointing green softwood: Evaluation of the interaction between polyurethane adhesive and wood

Abstract

Existing European standards for finger-jointing of load-bearing lumber require the wood to be dried before gluing. This article presents a study on the properties of green-glued finger joints, wet wood being bonded prior to drying. Issues to consider, in comparison to finger-jointing of dry wood, are mechanical performance of the joint, absorption of the polymer by the wood in its natural/wet state, and the chemical reactions of the adhesive on contact with water. Finger-jointed samples were tested in bending, and the glue joints analysed by optical microscopy, scanning electron microscopy and microdensitometry. A patented one-component polyurethane adhesive developed for gluing-green wood which has a moisture content usually higher than 70% was used in the study. The resulting green-glued joints showed improved strength properties in comparison to dry-jointed joints. The results confirm that green-glued joints provide a wide, continuous wood/adhesive interface from one substrate to the other. The adhesive penetrates several cells deep and the density of the wood adjacent to the joint surfaces is increased. The results also indicate that the patented adhesive forms covalent bonds to the wood substrate.     

Vibrational properties of harp soundboard with respect to its multi-layered structure

The vibrational properties of a harp soundboard were investigated with respect to its multi-layered structure. The surfaces of harp soundboards are usually reinforced with veneer; however, this reduces the specific dynamic Young’s modulus (E′/ρ) and significantly increases the internal friction (Q ^?1) of soundboards. Since smaller E′/ρ and greater Q ^?1 values impart a smaller acoustic conversion efficiency, the attachment of veneer is predicted to reduce the amplitude of the sound produced, as suggested by harp makers. The vibrational properties of veneer-reinforced wood are elucidated using a multi-layered model comprising base wood, a glue layer, veneer and a varnish layer. The results of calculations suggest that a thinner veneer attached with minimal glue would increase the sound amplitude.     

Effects of slash chips placed around trees planted after whole-tree logging: movement and nutrient supply

 Whole-tree harvesting at clearcutting sites using cable yarding systems and processors disrupts the process of nutrient return via leafy and woody slash otherwise left on the forest floor. This study examined the effect of placing slash chips around trees planted in a clearcut area. Chips made from branches with needles (branch chips) and three types of wood scrap chips (wood chips) were prepared for the study. Changes in the thickness of slash chip layers and in the concentration and weight of decomposing chips were measured. The nutrient effect of applying chips to the soil was analyzed, and the effects of chip coverage on weed control were measured. The branch and 18-mm-thick wood chips were stable on slopes; 9- and 4-mm-thick wood chips readily shifted to the lower and outer positions in the plots. On branch chips and wood chips, the annual rate of decomposition (k) calculated by exponential model was 0.69–0.7 and 0.04–0.17/year, respectively. Branch chips provided more nutrients for decomposers, and were rapidly decomposed during the first month. Nevertheless, the nutrient effect on the soil could not be confirmed. Placing branch or wood chips around planted trees effectively eliminated the need for weeding for 1 year, but these light materials did not suppress shrub sprouting. Received: November 14, 2001 / Accepted: September 26, 2002 Acknowledgments The authors thank the graduates of Kochi University, especially Ms. Y. Shinnobu, Ms. A. Fujita, Ms. A. Sugiyama, and Ms. Y. Suzuki for their help with the field work and chemical analyses. This study was supported by a Grant-in-Aid for Scientific Research (No. 09660164) from the Ministry of Education, Culture, Sports, Science and Technology of Japan. Correspondence to:J. Gotou     

Comparative study on the durability of heat-treated White Birch (Betula papyrifera) subjected to the attack of brown and white rot fungi

Abstract

The effect of heat treatment on decay resistance of white birch was evaluated for different incubation periods ranging from 2 to 12 weeks using three species of brown rot and one species of white rot fungus. The results of weight loss tests showed that the white rot fungus, Trametes versicolor, effectively degraded the untreated wood (73.5%). While the degradation of untreated wood by brown rot fungi species, Gloephyllum trabeum (11.6%) and Conifora puteana (6.2%), was considerably less compared to T. versicolor, the third brown rot fungi studied, Poria placenta, caused an appreciable degradation of the same species (52.4%). The results clearly showed that the heat treatment reduced the effect of fungi attack on white birch. Increasing the heat treatment temperature from 195 to 215°C resulted in reduction of weight loss, consequently, reduction in fungal attack. As an example, the weight loss reductions due to T. versicolor, P. placenta, G. trabeum and C. puteana attack was 62.2%, 71.3%, 89.6% and 100%, respectively, compared to the weight loss of untreated wood when it is heat treated at 215°C. Thus, these results confirmed that the heat treatment increased the biological resistance of white birch.     

Reactions between Cr(VI) and wood and its model compounds

Wood, macromolecular and simple model compounds, were reacted with CrO₃ or K₂CrO₄ aqueous solutions. Extracted lignin, guaiacol, vanillin, vanillyl alcohol and homovanillyl alcohol were chosen as model compounds for lignin, whilst cellulose, gum Ghatti, xylan, extracted hemicellulose from pine, methyl-β-D-glucopyranoside and methyl-β-cellobioside were used as models for wood polysaccharides. The kinetics of the reduction reactions of Cr(VI) were monitored using UV-Vis spectroscopy and the results obtained for several temperatures are discussed. In general terms, wood, lignin and lignin model compounds reduced Cr(VI) faster and to a greater extent than polysaccharides or simple sugar molecules. Moreover, lignin model compounds were reduced even faster than lignin. Simple sugars showed a reduction pattern similar to that of cellulose. Extracted hemicellulose revealed to be a poorer reductant while gum Ghatti was the strongest among the polysaccharides. As expected, CrO₃ aq. behaved as a more powerfull oxidant than K₂CrO₄ aq. for these substances. Even at 100 °C, sugars or polysaccharides did not seem to be oxidised by K₂CrO₄ aq. 0.01 M. These results suggest that, because of the differences in reactivity, lignin reacts preferentially when wood is treated with Cr(VI)-containing formulations, like those which are applied in wood preservation treatments.     

Stiffness moduli of various softwood and hardwood species determined with ultrasound

Abstract

Comprehensive data sets of the elastic constants are available for only a few European wood species. The goal of this study was to provide stiffnesses for the principal directions and planes for further selected European softwoods and hardwoods, to extend the currently existing data sets. For this purpose, a dynamic technique was chosen: the moduli were estimated on the basis of sound velocity and density measurements. The collected data may be helpful for specialists in the relevant research and practical fields, particularly when stresses and strains of structural elements have to be calculated using modelling approaches.     

Crack influence on load-bearing capacity of glued laminated timber using extended finite element modelling

Abstract

Most of the cracks are caused by changes in temperature and relative humidity which lead to shrinkage and swelling of the wood and thereby induce stresses in the structure. How these cracks influence the strength of the wooden structure, especially the shear strength, is not well understood. However, it is reasonable to expect that cracks have an impact on the shear strength as they preferably run along the beams in the direction of grain and bond lines. The purpose of this study was to investigate the load-bearing capacity of cracked glulam beams and to find a model that could predict the failure load of the beams due to the cracks. Three-point bending tests were used on glulam beams of different sizes with pre-manufactured cracks. An orthotropic elastic model and extended finite element method was used to model the behaviour of the cracked beams and to estimate the load-bearing capacity. The conclusions were validated by numerical simulations of the mechanical behaviour of three-point bending of glulam beams with different crack locations. The crack initiation load was recorded as the failure load and compared to the experimental failure load. The results of the compaction simulations agree well with the experimental results.     

Reducing set-recovery of compressively densified poplar wood by impregnation–modification with melamine–formaldehyde resin

ABSTRACT

Densification of resin impregnated wood under hot-pressing is a method that along with the potential for the reduction of set-recovery could additionally increase the density of wood and further improve other technical properties. In this study, the effect of the methylated melamine-formaldehyde modification on the shape memory effect of densified Populous nigra wood at various compression ratio levels was investigated. Furthermore, the effects on moisture content and compression ratio were also assessed. The most important conclusion drawn was that MF can act as a means for reducing set-recovery of compressed poplar wood since it is obvious that the use of MF significantly improved the stability of densified wood due to the formation of new bonds between cell wall components and MF. In the case of densification under stress of 10?kg/cm², the stabilization was improved by the use of MF to about 50% compared to water-treated specimens. The effect of MF on the stabilization of densified wood was not very clear for stresses higher than 10?kg/cm² since due to the outflow of MF solution during the first minutes of compression.     

Real-time wood moisture-content determination using dual-energy X-ray computed tomography scanning

ABSTRACT

The estimation of the pixel-wise distribution of the moisture content (MC) in wood using X-ray computed tomography (CT) requires two scans of the same wood specimen at different MCs, one of which is known. Image-processing algorithms are needed to compensate for the anisotropic distortion that wood undergoes as it dries. An alternative technique based on dual-energy CT (DECT) to determine MC in wood has been suggested by several authors. The purpose of the present study was to evaluate the hypothesis that DECT can be used for the determination of MC in real time. A method based on the use of the quotient between the linear attenuation coefficients (μ) at different acceleration voltages (the so-called quotient method) was used. A statistical model was created to estimate the MC in solid sapwood of Scots pine, Norway spruce and brittle willow. The results show a regression model with R²?>?0.97 that can predict the MC in these species with a RMSE of prediction of 0.07, 0.04 and 0.11 (MC in decimal format) respectively and at MC levels ranging from the green to the totally dry condition. Individual measurements of MC show an uncertainty of up to ±0.4. It is concluded that under the conditions prevailing in this study, and in studies referred to in this paper, it is not possible to measure MC with DECT.     

Energy Audit of Wood Harvesting Systems

A computer-based model for the evaluation of energy use in mechanized wood harvesting systems (EnergyCalc) was developed with aid of life cycle analysis methodologies. The system boundaries were determined "from stump to roadside" with wood volume over bark (m³) as the functional unit. The computer model (based on a database system) used a Visual Basic program, and the energy audit was based on fuel and oil consumption, and the energy consumed in the manufacture of the machines and replacement parts. The general scenario from the literature, results from Sweden and a preliminary study from Ireland are presented. In the overall energy audit of mechanized wood harvesting systems in Ireland, fuel consumption was the most significant item (82%), followed by oils (7%) and machine repairs and replacement (11%). The mean energy use from the data for Ireland was found to be 16% higher than the equivalent in Sweden (120 vs 103 MJ m^?3). An energy reduction strategy that has the potential to reduce overall energy consumption for Irish systems by up to 13% was suggested.     

Effects of Lime and Wood Ash on Soil-solution Chemistry,Soil Chemistry and Nutritional Status of a Pine Stand in Northern Germany

Lime and wood ash may be useful to improve acidic forest soils. A field experiment was conducted in a pine stand on a sandy podzol at Fuhrberg, Germany, which involved an application of dolomitic lime (3 t ha^-1) with three replications or wood ash (4.8 t ha^-1) without replications on the forest floor. During the 2 yr study period, lime affected the soil solution composition only slightly. Ash had a marked effect on solution chemistry of the mineral soil at 10 cm and the pH values dropped temporarily from 3.7 to 3.1. Nineteen months after the treatments, exchangeable calcium in the organic layer and mineral soil increased by 222 (lime addition) or 411 kg ha^-1 (ash addition) and exchangeable magnesium increased by 101 (lime addition) or 39 kg ha^-1 (ash addition). After ash addition, no marked change in heavy metal content was found below 4 cm of the organic layer. In the ash treatment, the potassium concentration of the 1-yr-old pine needles increased from 5.6 to 5.9 g kg^-1. This study suggests that ash from untreated wood may be recommended for amelioration of forest soils.     

Tensile strength of softwood butt end joints. Part 1: Effect of grain angle on adhesive bond strength

Abstract

To study the effect of grain angle on the adhesive bond strength in wood, three-part Norway spruce wood specimens were bonded and tested in tension. The two axially orientated outer parts of the specimens were joined with the middle part by means of three adhesives typically used for load-bearing constructions, i.e. one-component polyurethane (PUR), melamine–urea–formaldehyde (MUF) and phenol–resorcinol–formaldehyde (PRF). The grain angle of the middle part was varied from 0° (end grain to end grain) to 90° (flat grain to end grain) in incremental steps of 10°. In general, PRF- and MUF-bonded samples exhibited highest tensile strength at end grain to end grain orientation of the three parts, while specimens bonded with PUR showed only 25% of the strength measured for PRF and MUF, respectively. At high grain angles (90°) all specimens showed similar strength values in the range of 30% of maximum strength of MUF- and PRF-bonded specimens. To explain the changing strength levels at different grain angle a composite failure criterion was applied.     

尾叶桉与赤桉正反析因交配杂种F_1材性遗传参数的估算

[目的]通过尾叶桉与赤桉杂种F1材质性状的遗传参数估算及其分析,为桉树杂交育种材性改良亲本选配和交配设计提供理论依据。[方法]以尾叶桉与赤桉6×6正反析因交配杂种F1测定林为材料,并以相应亲本自由授粉的半同胞子代作对照。9年生时,对各小区的杂种和家系(5株小区,6次重复)选取2株平均木,在胸高1. 3 m处沿南北向钻取木芯,共984个,测定木材基本密度、纤维长、纤维宽和纤维长宽比,利用ASReml-R估算4个材质指标的特殊配合力、杂种优势、父母本单株狭义遗传力、遗传相关和表型相关系数。[结果]表明:尾叶桉与赤桉正反交的杂种木材基本密度优于对照,呈明显的杂种优势;反交组合杂种其木材基本密度优于正交组合杂种,正交组合杂种的纤维特性优于反交组合的;在正交组合杂种中,木材基本密度、纤维长和纤维长宽比的母本效应低于父本效应;而反交组合杂种中,4个材质指标的母本效应均高于父本效应。木材基本密度和纤维特性指标受中至低遗传控制。正反交组合杂种中,除纤维长宽比外,其余3个材质指标的显性效应大于加性效应。对于遗传相关,杂种的木材基本密度与纤维宽呈极显著的负相关,与纤维长宽比呈极显著的正相关,与纤维长呈不显著负相关,纤维长与纤维宽呈显著正相关。对于表型相关,除纤维宽与纤维长宽比呈不显著正相关外,其余性状间均呈极显著正相关。[结论]尾叶桉与赤桉杂种的材质性状遗传差异因亲本和交配方式而异,表明通过种间杂交和正向选择进行材质性状的遗传改良具有潜力。     

Comparative study of anatomy and lignin distribution in normal and tension wood of Salix gordejecii

Fibre morphology, anatomy and ultrastructure in cell wall of Salix gordejecii normal wood were examined by transmission electron microscopy (TEM). S. gordejecii tension wood can be recognized anatomically by the presence of gelatinous (G) fibres, which contain a conspicuously thickened inner cell wall layer. TEM images showed that cell wall of S. gordejecii normal wood was typically divided into three layers including the primary wall (P), the middle lamellar (ML) and the secondary wall (S₁, S₂ and S₃). Lignin distribution was determined by using confocal laser scanning microscopy (CLSM) and transmission electron microscopy with energy dispersive X-ray analysis (TEM-EDXA). Confocal images (530 nm) of S. gordejecii normal wood showed strongly lignified CCML, and weakly lignified ML and S2 layer. Weakly lignified fibres (F) and strongly lignified vessels (V) were also detected by using CLSM. Results obtained from confocal microscopy were further confirmed by using TEM-EDXA, indicating that the ratio of lignin concentration in CCML, ML and S2 is 1.72 (1321):1.31 (1006):1 (768). Lignin distribution in tension wood is similar to that in normal wood, except for the non-lignified G layer.     

Wood transportation machine replacement using goal programming

ABSTRACT

Farm tractor?+?trailers play a key role in wood transportation after forests are logged. Despite of the fact that a forwarder is a forestry vehicle that carries felled logs for shorter distances off the ground, tractors are still used in some forest areas of the world, such as the Hyrcanian forest in northern Iran. This study was conducted to investigate the possibility of using both the light forwarder and forestry trailer instead of a farm tractor?+?trailer in wood transportation. The optimal machine option for wood transportation is determined using goal programming model in the study area. In this paper, multi-objective goals (such as economic, operational, environmental and ergonomic) were considered. The results showed that considering only the economic goal, the contractor could save up to 44% in costs by purchasing and replacing a forestry trailer with a 2-wheel trailer attached to the farm tractor. In addition, considering various goals, a light forwarder could be selected as the optimal machine. Currently, the most important objectives of all forest contractors are to establish economic goals and reduce wood transportation costs. Since other goals, such as environmental and ergonomic, are also important; it is suggested that multi-objective approaches should use for planning.     

Decaying wood and tree regeneration in the Acadian Forest of Maine,USA

We examined the effect of management history on the availability of decayed downed wood and the use of downed wood as a regeneration substrate in mixed-species stands in the Acadian Forest of Maine. Regeneration of red spruce (Picea rubens Sarg.), eastern hemlock (Tsuga canadensis (L.) Carr.), balsam fir (Abies balsamea L. Mill), and red maple (Acer rubrum L.) was quantified. Treatments included variants of selection cutting, commercial clearcutting (unregulated harvesting), and no harvesting for >50 years (reference). Area of wood substrate (wood ≥ Decay Class III and ≥10 cm on at least one end) was less in the commercial clearcut than in the reference; other treatments were not differentiated. Spruce and hemlock seedlings were found at higher densities on wood than paired forest floor plots of equal area, regardless of treatment. Conversely, fir and maple were less abundant on wood than forest floor plots in reference and selection treatments, but more or equally abundant on wood than forest floor plots in the commercial clearcut. These findings suggest that silvicultural treatment affects both the availability of decayed downed wood and seedling-substrate relationships, and that forest management in the Acadian Region should consider availability of downed woody material.