Interactions of whey proteins during heat treatment of oil-in-water emulsions formed with whey protein isolate and hydroxylated lecithin

The interactions of proteins during the heat treatment of whey-protein-isolate (WPI)-based oil-in-water emulsions with and without added hydroxylated lecithin were studied by examining the changes in droplet size distribution and the quantity and type of adsorbed and unadsorbed proteins. Heat treatment at 90 degrees C of WPI emulsions resulted in an increase in total adsorbed protein; unadsorbed beta-lactoglobulin (beta-lg) was the main protein interacting with the adsorbed proteins during the first 10 min of heating, but after this time, unadsorbed alpha-lactalbumin (alpha-la) also associated with the adsorbed protein. In emulsions containing hydroxylated lecithin, the increase in total adsorbed protein during heat treatment was much lower and the unadsorbed beta-lg did not appear to interact with the adsorbed proteins during heating. However, the behavior of alpha-la during heat treatment of these emulsions was similar to that observed in the emulsions containing no hydroxylated lecithin. In the presence of NaCl, the particle size of the emulsion droplets and the quantities of adsorbed protein increased markedly during heating. Emulsions containing hydroxylated lecithin were less sensitive to the addition of NaCl. These results suggest that the binding of hydroxylated lecithin to unfolded monomers or intermediate products of beta-lg reduces the extent of heat-induced aggregation of beta-lg and consequently decreases the interactions between unadsorbed beta-lg and adsorbed protein. This was confirmed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) of heated whey protein and hydroxylated lecithin solutions.     

甘薯热变性蛋白限制性酶解产物的乳化特性研究

采用5种酶(Alcalase 2.4L, As1.398, Neutrase, Pepsin, Trypsin)对甘薯热变性蛋白(SPHP)进行限制性酶解。将各酶解产物离心后分别取上清和沉淀测定和观察其乳化液的乳化颗粒平均粒径(D_4,3)、乳化活性指数(EAI)、乳化稳定性指数(ESI)、乳化液的微观结构和表观黏度。结果显示:酶解产物上清和沉淀中蛋白的溶解度均有增加,但沉淀增加的幅度小于上清。SPHP的D_4,3是71.96μm,而酶解产物上清和沉淀乳化液的D_4,3均减小,且上清的D_4,3小于沉淀的。在5种酶解产物中,Pepsin酶解物上清的D_4,3最小,为14.94μm。SPHP酶解后上清的乳化颗粒大小较为均一,且沉淀的乳化颗粒酶解前后变化不大。SPHP的EAI为11.21m2/g,酶解产物上清和沉淀的EAI均有显著提高(P<0.05),其中Pepsin酶解物上清的EAI最高为70.32m2/g。此外,酶解产物上清和沉淀乳化液的ESI增大。与沉淀相比,5种酶解产物的上清具有较低的表观黏度,且酶解产物上清和沉淀的乳化液均呈剪切变稀的非牛顿流体特性。     

Impact of whey protein emulsifiers on the oxidative stability of salmon oil-in-water emulsions

To obtain a better understanding of how the interfacial region of emulsion droplets influences lipid oxidation, the oxidative stability of salmon oil-in-water emulsions stabilized by whey protein isolate (WPI), sweet whey (SW), beta-lactoglobulin (beta-Lg), or alpha-lactalbumin (alpha-La) was evaluated. Studies on the influence of pH on lipid oxidation in WPI-stabilized emulsions showed that formation of lipid hydroperoxides and headspace propanal was much lower at pH values below the protein's isoelectric point (pI), at which the emulsion droplets were positively charged, compared to that at pH values above the pI, at which the emulsion droplets were negatively charged. This effect was likely due to the ability of positively charged emulsion droplets to repel cationic iron. In a comparison of lipid oxidation rates of WPI-, SW-, beta-Lg-, and alpha-La-stabilized emulsions at pH 3, the oxidative stability was in the order of beta-Lg > or = SW > alpha-La > or = WPI. The result indicated that it was possible to engineer emulsions with greater oxidative stability by using proteins as emulsifier, thereby reducing or eliminating the need for exogenous food antioxidants.     

Production and characterization of oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin-pectin membranes

Oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin (beta-Lg)-pectin membranes were produced using a two-stage process. A primary emulsion containing small droplets (d(32) approximately 0.3 microm) was prepared by homogenizing 10 wt % corn oil with 90 wt % aqueous solution (1 wt % beta-Lg, 5 mM imidazole/acetate buffer, pH 3.0) using a high-pressure valve homogenizer. The primary emulsion was then diluted with pectin solutions to produce secondary emulsions with a range of pectin concentrations (5 wt % corn oil, 0.45 wt % beta-Lg, 5 mM imidazole/acetate buffer, 0-0.22 wt % pectin, pH 3.0). The electrical charge on the droplets in the secondary emulsions decreased from +33 +/- 3 to -19 +/- 1 mV as the pectin concentration was increased from 0 to 0.22 wt %, which indicated that pectin adsorbed to the droplet surfaces. The mean particle diameter of the secondary emulsions was small (d(32) < 1 microm) at relatively low pectin concentrations (<0.04 wt %), but increased dramatically at higher pectin concentrations (e.g., d(32) approximately 13 microm at 0.1 wt % pectin), which was attributed to charge neutralization and bridging flocculation effects. Emulsions with relatively small mean particle diameters (d(32) approximately 1.2 microm at 0.1 wt % pectin) could be produced by disrupting flocs formed in secondary emulsions containing highly negatively charged droplets, for example, by sonication, blending, or homogenization. The particles in these emulsions probably consisted of small flocs containing a number of protein-coated droplets bound together by pectin molecules. These emulsions had good stability to further particle aggregation up to relatively high ionic strengths (< or =500 mM NaCl) and low pH (pH 3). The interfacial engineering technology used in this study could lead to the creation of food emulsions with improved physicochemical properties or stability.     

Physical and oxidative stability of fish oil-in-water emulsions stabilized with beta-lactoglobulin and pectin

The oxidation of fatty acids can be inhibited by engineering the surface of oil-in-water emulsion droplets to decrease interactions between aqueous phase prooxidants and lipids. The objective of this research was to evaluate whether emulsions stabilized by a multilayer emulsifier systems consisting of beta-lactoglobulin and citrus or sugar beet pectin could produce fish oil-in-water emulsions that had good physical and oxidative stability. Sugar beet pectin was compared to citrus pectin because the sugar beet pectin contains the known antioxidant, ferulic acid. A primary Menhaden oil-in-water emulsion was prepared with beta-lactoglobulin upon which the pectins were electrostatically deposited at pH 3.5. Emulsions prepared with 1% oil, 0.05% beta-lactoglobulin, and 0.06% pectins were physically stable for up to 16 days. As determined by monitoring lipid hydroperoxide and headspace propanal formation, emulsions prepared with the multilayer system of beta-lactoglobulin and citrus pectin were more stable than emulsions stabilized with beta-lactoglobulin alone. Emulsions prepared with the multilayer system of beta-lactoglobulin and sugar beet pectin were less stable than emulsions stabilized with beta-lactoglobulin alone despite the presence of ferulic acid in the sugar beet pectin. The lower oxidative stability of the emulsions with the sugar beet pectin could be due to its higher iron and copper concentrations which would produce oxidative stress that would overcome the antioxidant capacity of ferulic acid. These data suggest that the oxidative stability of oil-in-water emulsions containing omega-3 fatty acids could be improved by the use of multilayer emulsion systems containing pectins with low metal concentrations.     

Influence of competitive adsorption on flocculation and rheology of high-pressure-treated milk protein-stabilized emulsions

The effect of high-pressure treatment (HPT) on the droplet-size distribution and small-deformation rheology of oil-in-water emulsions containing beta-lactoglobulin and a nonionic surfactant or sodium caseinate has been investigated at neutral pH. Addition of Tween 20 (polyoxyethylenesorbitan monolaurate) to a beta-lactoglobulin-stabilized emulsion results in competitive displacement of the adsorbed globular protein film and, following HPT, the formation of a less flocculated emulsion. The age of the beta-lactoglobulin-stabilized emulsion prior to addition of sodium caseinate influences the competitive adsorption behavior. The strengthening of the beta-lactoglobulin layer with time makes it more resistant to disruption by sodium caseinate. The level of pressure-induced flocculation of beta-lactoglobulin-coated oil droplets depends on the intensity of processing conditions and on the degree of interfacial displacement. In contrast, beta-lactoglobulin added after emulsification appears to show little evidence of competitive adsorption behavior at the caseinate oil-water interface. Changes in the rheological properties of these latter systems following HPT can be attributed to pressure-induced denaturation and gelation of beta-lactoglobulin in the continuous phase of the emulsion.     

Effect of interfacial protein cross-linking on the in vitro digestibility of emulsified corn oil by pancreatic lipase

The objective of this study was to investigate the influence of globular protein interfacial cross-linking on the in vitro digestibility of emulsified lipids by pancreatic lipase. 3% (wt/wt) corn oil-in-water emulsions stabilized by either lecithin or beta-lactoglobulin were prepared (pH 7). A portion of the beta-lactoglobulin stabilized emulsions was subjected to a heat treatment known to cross-link the adsorbed globular proteins (85 degrees C, 20 min). Pancreatic lipase and bile extract were then added to each emulsion at 37 degrees C (pH 7) and the evolution of the particle charge, particle size, appearance and free fatty acids released were measured over a period of 2 h. The rate and extent of lipid digestion did not differ greatly between lecithin and beta-lactoglobulin stabilized emulsions, nor did it differ greatly for unheated (BLG-U) or heated (BLG-H) beta-lactoglobulin stabilized emulsions. For example, the initial rate of lipid digestion was found to be 3.1, 3.4, and 2.3 mM fatty acids s(-1) m(-2) of lipid surface for droplets stabilized by BLG-U, BLG-H, and lecithin, respectively. Pancreatic lipase was able to adsorb to the droplet surfaces and access the emulsified lipids, regardless of the initial interfacial composition and the fact that some of the original emulsifier appeared to remain at the oil-water interface during digestion. These results help to explain why the human body is so efficient at digesting dietary triacylglycerols.     

Role of proteins in oil-in-water emulsions on the stability of lipid hydroperoxides

The purpose of this research was to better understand the mechanisms by which proteins affect the rates of lipid oxidation in order to develop protein-stabilized emulsion delivery systems with maximal oxidative stability. This study evaluated the affect of pH and emulsifier concentration on the stability of cumene hydroperoxide in hexadecane-in-water emulsions stabilized by beta-lactoglobulin (beta-Lg). Emulsions prepared with 0.2 wt % beta-Lg (at pH 7.0) showed a 26.9% decrease in hydroperoxide concentrations 5 min after 0.25 mM ferrous ion was added to the emulsion. EDTA, but not continuous phase beta-Lg, could inhibit iron-promoted lipid hydroperoxide decomposition. Lipid hydroperoxides were more stable to iron-promoted degradation at pH values below the pI of beta-Lg, where the emulsion droplet would be cationic and thus able to repel iron away from the lipid hydroperoxides. Heating the beta-Lg-stabilized emulsions to produce a cohesive protein layer on the emulsion droplet surface did not alter the ability of iron to decompose lipid hydroperoxides. These results suggest that proteins at the interface of emulsion droplets primarily stabilize lipid hydroperoxides by electrostatically inhibiting iron-hydroperoxide interactions.     

Heat-induced destabilization of oil-in-water emulsions formed from hydrolyzed whey protein.

The emulsifying ability, heat stability, and coalescence stability of oil-in-water emulsions prepared with whey protein of varied degrees of hydrolysis (DH), and at varied protein contents, was studied. Whey protein hydrolysates (WPH) with a DH of 4% and 10% had poorer emulsifying ability than non-hydrolyzed whey protein concentrate (WPC), but were more heat stable. Increasing DH between 10 and 27% improved emulsifying ability and further improved the heat stability of the emulsion droplets. Increasing DH from 27 to 35% led to a big decrease in both emulsifying ability and heat stability. The quiescent coalescence stability of WPH emulsions was relatively good up to a DH of 27%. Above DH 27% emulsions become highly unstable. It appears that two mechanisms of instability are at work here. At low DH heat-induced denaturation and aggregation occur. In the DH range of 4-20% heat stability increases as protein globular structure is disrupted. At a DH greater than 27% we see a change from a hydrolysis-induced increase in heat-stability to coalescence instability, with a resultant large increase in emulsion breakdown during heating.     

适宜物理-酶联合改性提高酸性条件下大豆分离蛋白乳化性

为提高酸性条件下大豆分离蛋白（soy protein isolates,SPI）的乳化性能,该文研究了物理-酶联合改性对SPI（pH值为4）的乳化性能影响,通过对比确定了物理-酶联合改性,即超声波-酶复合改性和挤压膨化-酶复合改性两种改性方法在酸性条件下的乳化性能效果最好;并通过对改性后 SPI（pH 值为4）进行溶解性、游离巯基、二硫键、粒径、扫描电镜（scanning electron microscope,SEM）和激光共焦扫描显微镜（confocal laser scanning microscopy,CLSM）分析,从蛋白结构变化上进一步揭示了乳化性能提高现象的原因。结果表明：超声波联合植酸酶-酸性蛋白酶改性的 SPI （Uphy-aci-SPI）的乳化活性（emulsifying activity index,EAI）为0.53 m2/g,比未改性SPI（0.18 m2/g）显著提高了196%（P<0.05）,乳化稳定性（emulsifying stability index,ESI）为17 min,比未改性SPI（13.5 min）显著提高了25.9%（P<0.05）;挤压膨化联合菠萝蛋白酶改性的SPI（Ebro-SPI）的EAI为0.46 m2/g,比未改性SPI显著增加了155%（P<0.05）,ESI为17 min,比未改性SPI显著增加了25.9%（P<0.05）。在pH值为4的条件下对物理-酶联合改性的SPI的性质分析发现,物理-酶联合改性的SPI与未改性SPI相比,物理-酶联合改性的SPI的溶解性显著增加（P<0.05）;物理-酶联合改性的SPI的乳状液平均粒径减小,CLSM观察乳状液中油与蛋白溶液稳定共融,改善了油滴之间的空间排斥力。物理-酶联合改性的SPI游离巯基的含量显著增加（P<0.05）,二硫键含量显著降低（P<0.05）。SEM观察物理-酶联合改性的SPI为结构松散、破碎均一的微观结构。由此可见,乳化性能的提高是通过深层改变蛋白的结构来实现的。该研究可为探索提高酸性条件下SPI的乳化性能的方法提供理论依据。     

Production and characterization of O/W emulsions containing cationic droplets stabilized by lecithin-chitosan membranes

Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion was prepared by homogenizing 5 wt % corn oil with 95 wt % aqueous solution (1 wt % lecithin, 100 mM acetic acid, pH 3.0) using a high-pressure valve homogenizer. This emulsion was diluted with aqueous chitosan solutions to form secondary emulsions with varying compositions: 1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0-0.04 wt % chitosan (pH 3.0). The particle size distribution, particle charge, and creaming stability of the primary and secondary emulsions were measured. The electrical charge on the droplets increased from -49 to +54 mV as the chitosan concentration was increased from 0 to 0.04 wt %, which indicated that chitosan adsorbed to the droplet surfaces. The mean particle diameter of the emulsions increased dramatically and the emulsions became unstable to creaming when the chitosan concentration exceeded 0.008 wt %, which was attributed to charge neutralization and bridging flocculation effects. Sonication, blending, or homogenization could be used to disrupt flocs formed in secondary emulsions containing droplets with high positive charges, leading to the production of emulsions with relatively small particle diameters (approximately 1 microm). These emulsions had good stability to droplet aggregation at low pH (< or =5) and ionic strengths (<500 mM). The interfacial engineering technology utilized in this study could lead to the creation of food emulsions with improved stability to environmental stresses.     

提高大豆蛋白冻融后乳化性改性工艺优化

为了制备出经冷冻-融化后仍能保持较高乳化性的大豆蛋白,试验以葡聚糖为糖基化供体,采用湿法糖基化技术改性大豆蛋白。根据单因素试验的结果,建立了Box-Behnken模型对加工工艺进行优化,所得的模型拟合度高,切实可行,可用于实际分析和预测。利用响应面分析法探讨了蛋白浓度、蛋白与糖质量比、反应时间3因素对改性产物冻融前后乳化活性和乳化稳定性的影响,优化的工艺条件为:大豆分离蛋白(soybean protein isolate,SPI)质量浓度40 mg/mL,SPI与葡聚糖的质量比为1∶3,反应时间4 h。在此条件下得到的改性产物冻融稳定性显著(P0.05)高于未改性蛋白,冻融前后的乳化活性(emulsifying activity index,EAI)分别是空白对照样的1.687和1.780倍,乳化稳定性(emulsion stability index,ESI)分别是空白对照样的1.367和1.274倍。傅里叶红外光谱证明葡聚糖通过共价键接到大豆蛋白分子中,研究结果为制备冷冻食品加工专用大豆蛋白的产业化生产提供参考。     

Role of continuous phase protein on the oxidative stability of fish oil-in-water emulsions

Whey protein isolate (WPI), soy protein isolate (SPI), and sodium caseinate (CAS) can inhibit lipid oxidation when they produce a positive charge at the interface of emulsion droplets. However, when proteins are used to stabilize oil-in-water emulsions, only a fraction of them actually absorb to the emulsion droplets, with the rest remaining in the continuous phase. The impact of these continuous phase proteins on the oxidative stability of protein-stabilized emulsions is not well understood. WPI-stabilized menhaden oil-in-water emulsions were prepared by high-pressure homogenization. In some experiments WPI was removed from the continuous phase of the emulsions through repeated centrifugation and resuspension of the emulsion droplets (washed emulsion). Unwashed emulsions were more oxidatively stable than washed emulsions at pH 7.0, suggesting that continuous phase proteins were antioxidative. The oxidative stability of emulsions containing different kinds of protein in the continuous phase decreased in the order SPI > CAS > WPI, as determined by both hydroperoxide and headspace propanal formation. Iron-binding studies showed that the chelating ability of the proteins decreased in the order CAS > SPI > WPI. The free sulfhydryls of both WPI and SPI were involved in their antioxidant activity. This research shows that continuous phase proteins could be an effective means of protecting omega-3 fatty acids from oxidative deterioration.     

Fibril assemblies in aqueous whey protein mixtures

Fibril formation in mixtures of whey proteins upon heating at pH 2 was investigated. Fibrils were found to coexist with other structures, such as spherulites. These spherulites consist of radially oriented fibrils. At total protein concentrations above 6 wt %, transparent gels were formed. Changing the ratio between the various whey proteins did not affect this gelation concentration as long as beta-lactoglobulin (beta-lg) was present, suggesting that beta-lg was dominant in the gelation. Pure alpha-lactalbumin and pure bovine serum albumin did not form fibrils, nor did they gel upon heating at pH 2 and 80 degrees C for up to 10 h. They did however induce a decrease in the beta-lg concentration needed for gel formation upon heating at pH 2. Our results suggest that beta-lg is the only fibril forming protein at the conditions used and that no mixed fibrils are formed.     

Impact of protein surface denaturation on droplet flocculation in hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin

The influence of globular protein denaturation after adsorption to the surface of hydrocarbon droplets on flocculation in oil-in-water emulsions was examined. n-Hexadecane oil-in-water emulsions (pH 7.0) stabilized by beta-lactoglobulin (1-wt % beta-Lg) were prepared by high-pressure valve homogenization. NaCl (0-150 mM) was added to these emulsions immediately after homogenization, and the evolution of the mean particle diameter (d) and particle size distribution (PSD) was measured by laser diffraction during storage at 30 degrees C for 48 h. No change in d or PSD was observed in the absence of added salt, which indicated that these emulsions were stable to flocculation. When 150 mM NaCl was added to emulsions immediately after homogenization, d increased rapidly during the following few hours until it reached a plateau value, while the PSD changed from monomodal to bimodal. Addition of N-ethylmaleimide, a sulfhydryl blocking agent, to the emulsions immediately after homogenization prevented (at 20 mM NaCl) or appreciably retarded (at 150 mM NaCl) droplet flocculation. These data suggests that protein unfolding occurred at the droplet interface, which increased the hydrophobic attraction and disulfide bond formation between droplets. In the absence of added salt, the electrostatic repulsion between droplets was sufficient to prevent flocculation, but in the presence of sufficient salt, the attractive interactions dominated, and flocculation occurred.     

Influence of pH and iota-carrageenan concentration on physicochemical properties and stability of beta-lactoglobulin-stabilized oil-in-water emulsions

The influence of pH and iota-carrageenan concentration on the properties of beta-lactoglobulin (beta-Lg)-stabilized oil-in-water emulsions was investigated by measuring the particle charge, particle size distribution, and creaming stability. Emulsions containing droplets stabilized by beta-Lg were produced by homogenization, and then, iota-carrageenan was added. At pH 3, the droplet charge did not change for iota-carrageenan concentrations 相似文献   

Beta-lactoglobulin-dextran conjugates: effect of polysaccharide size on emulsion stability

A series of dextrans and beta-lactoglobulin were covalently conjugated and screened for their ability to stabilize oil-in-water emulsions. Dextrans with the molecular mass of 19.6 kDa, 87 kDa, 150 kDa, 500 kDa, and 2000 kDa were attached to beta-lactoglobulin via the Maillard reaction. The conjugates were then purified and evaluated as emulsifiers under neutral conditions. The ability to stabilize emulsions was determined by monitoring oil droplet size over time. Adsorption of the conjugates to the droplet surface was characterized by determining the protein surface load. The results show that increasing polysaccharide size increases emulsion stability up to 150 kDa before leveling off. Conversely, surface protein density remains constant until 150 kDa before decreasing with polysaccharide size. A model is presented to interpret the results.     

Charge modifications to improve the emulsifying properties of whey protein isolate

Whey protein isolate was modified by ethylene diamine in order to shift its isoelectric point to an alkaline pH. The extent of the modification was studied using SDS-PAGE and MALDI-TOF mass spectrometry. The modified whey proteins were used as an emulsifier to stabilize oil-in-water emulsions at acidic and neutral pH ranges, and their emulsifying properties were compared with that of the unmodified whey proteins and with the previously studied ethylene diamine modified sodium caseinate. The emulsifying activity of the modified whey proteins was similar to that of the unmodified ones, but the stability of an emulsion at pH 5 was significantly improved after the modification. Charge and coverage of droplet surface and the displacement of the interfacial proteins by surfactant Tween 20 were further studied as a function of pH. As compared with the unmodified whey proteins, the modified ones were proven to cover the interface more efficiently with extensive surface charge at pH 5, although the interfacial layer was less resistant to the surfactant displacement.     

Lipid oxidation in corn oil-in-water emulsions stabilized by casein,whey protein isolate,and soy protein isolate

Proteins can be used to produce cationic oil-in-water emulsion droplets at pH 3.0 that have high oxidative stability. This research investigated differences in the physical properties and oxidative stability of corn oil-in-water emulsions stabilized by casein, whey protein isolate (WPI), or soy protein isolate (SPI) at pH 3.0. Emulsions were prepared with 5% corn oil and 0.2-1.5% protein. Physically stable, monomodal emulsions were prepared with 1.5% casein, 1.0 or 1.5% SPI, and > or =0.5% WPI. The oxidative stability of the different protein-stabilized emulsions was in the order of casein > WPI > SPI as determined by monitoring both lipid hydroperoxide and headspace hexanal formation. The degree of positive charge on the protein-stabilized emulsion droplets was not the only factor involved in the inhibition of lipid oxidation because the charge of the emulsion droplets (WPI > casein > or = SPI) did not parallel oxidative stability. Other potential reasons for differences in oxidative stability of the protein-stabilized emulsions include differences in interfacial film thickness, protein chelating properties, and differences in free radical scavenging amino acids. This research shows that differences can be seen in the oxidative stability of protein-stabilized emulsions; however, further research is needed to determine the mechanisms for these differences.     

Stabilization of model beverage cloud emulsions using protein-polysaccharide electrostatic complexes formed at the oil-water interface

The potential of utilizing interfacial complexes, formed through the electrostatic interactions of proteins and polysaccharides at oil-water interfaces, to stabilize model beverage cloud emulsions has been examined. These interfacial complexes were formed by mixing charged polysaccharides with oil-in-water emulsions containing oppositely charged protein-coated oil droplets. Model beverage emulsions were prepared that consisted of 0.1 wt % corn oil droplets coated by beta-lactoglobulin (beta-Lg), beta-Lg/alginate, beta-Lg/iota-carrageenan, or beta-Lg/gum arabic interfacial layers (pH 3 or 4). Stable emulsions were formed when the polysaccharide concentration was sufficient to saturate the protein-coated droplets. The emulsions were subjected to variations in pH (from 3 to 7), ionic strength (from 0 to 250 mM NaCl), and thermal processing (from 30 or 90 degrees C), and the influence on their stability was determined. The emulsions containing alginate and carrageenan had the best stability to ionic strength and thermal processing. This study shows that the controlled formation of protein-polysaccharide complexes at droplet surfaces may be used to produce stable beverage emulsions, which may have important implications for industrial applications.