Effect of different drying methods on liquid penetration of Chinese fir plantation wood

Chinese fir plantation sapwood and heartwood boards were treated by three drying methods: radio frequency-vacuum drying (RFVD), conventional kiln drying (KD) and high temperature drying (HTD). The maximum amount of dyeing solution uptake by the capillary rising method was used to evaluate the liquid penetration of the treated wood. The pit aspiration ratio was determined by a semithin section method. Changes in wood microstructure were investigated using scanning electron microscopy. The results show that liquid penetration of Chinese fir sapwood after RFVD is significantly higher than that after KD and HTD. Liquid penetration of Chinese fir heartwood after RFVD is higher than that after HTD. Liquid penetration of Chinese fir sapwood is significantly higher than that of heartwood after three drying treatments. Low pit aspiration ratio and cracks of some bordered pits are the main reasons for the increase in liquid penetration after RFVD treatment. __________ Translated from Scientia Silvae Sinicae, 2006, 42(10): 85–90 [译自: 林业科学]     

Effects of inorganic acid catalysts on liquefaction of wood in phenol

In order to obtain the effects of acid catalysts on wood liquefaction in phenol, we investigated the liquefaction of wood powder from Chinese fir (Cunninghamia lanceolata) and poplar (Triploid Populus tomentosa Carr) in the presence of phenol with the following weak inorganic acids as catalysts: phosphoric acid (85%), sulfuric acid (36%), hydrochloric acid (37%) and oxalic acid (99.5%). Results show that phosphoric acid (85%) and sulfuric acid (36%) are better than the other catalysts. It was found that lower residue ratios can be obtained under defined reaction conditions: phenol/wood ratio is 4, a 10% catalyst based on the weight of phenol, a temperature of 150°C for 2 h and phosphoric or sulfuric acid. The residue ratios are 3.2% and 4.0%, respectively. __________ Translated from Journal of Beijing Forestry University, 2004, 26(5) [译自: 北京林业大学学报, 2004, 26(5)]     

3种不同处理方法对木材渗透性影响的研究

本文通过对长白鱼鳞云杉和臭冷杉生材分别进行普通气干处理和酒精置换处理以及对其气干材进行水浸处理,研究了这３种不同处理方法对木材气渗透性的影响及其影响机理。研究结果表明,长白鱼鳞云杉边材、心材和臭冷杉心村的生材经普通气干处理后,其气体渗透性较低,分别约为０．１１４、０．０４５和０．１１１ｄａｒｃｙ;长白鱼鳞云杉边材、心材和臭冷杉心材的生材经酒精置换处理后,其气体渗透性分别约为１１．７１３、０．０７４和０．１４４ｄａｒｃｙ,比普通气干处理对照组试样的平均渗透性分别增加约１０１．５倍、６２％和３０％,ｔ检验表明,前者差异非常显著,但后两者差异不显著;已气干１８个月的长白鱼鳞云杉边材、心材和臭冷杉心材经水浸处理后,其平均气体浸透性较处理前分别增加约８５％、４９％、６５．５％,ｔ检验表明差异均显著。长白鱼鳞云杉生材边材经     

Relationships between longitudinal and radial Picea genera sound vibration parameters

Longitudinal sawn wood are usually selected as samples in the study of sound properties of a musical instrument board. But in real production, radial sawn timber are cut and are also widely used as vibration component. Therefore, it is very important to evaluate the vibration properties of the board in the round, especially for the sound radiation characteristic of radial sawn timber and its relationship to longitudinal sawn timber. However, for the national and international experts, researches on radial sawn timber and its role and function in sound emission have not yet been developed. This paper describes a study of seven important spruces that grow up in the Sichuan and Heilongjiang provinces of China, and one Picea sitchensis specimen from North America. Under the high bending vibration mode, resonance frequency and other parameters of longitudinal and radial wood were tested. Analysis result disclosed the relationship between longitudinal and radial wood vibration property. An important conclusion of wood for musical instruments with proper anisotropy, fine toughness, and weak shear of longitudinal and radial vibration was inducted. __________ Translated from Scientia Silvae Sinicae, 2006, 42(3): 21–24 [译自: 林业科学, 2006, 42(3): 21–24]     

Prediction of mechanical properties of Chinese fir wood by near infrared spectroscopy

Mechanical properties and the visible and near infrared (NIR) (350–2500 nm) spectra obtained from longitudinal and transverse face of 155 small clear wood samples of Chinese fir (Cunninghamia lanceolata) were measured, and 103 of them were used to establish calibration models. Calibrations were tested on an independent set (52 samples). Differences between calibrations developed by using the longitudinal and transverse face were small. The calibrations developed by using NIR spectra (350–2500 nm) collected from transverse face were slightly inferior to those developed by using NIR spectra collected from longitudinal face. When reducing the spectral range to between 780 and 1050 nm, the calibrations developed by using NIR spectra collected from longitudinal face were slightly inferior to those developed by using NIR spectra collected from transverse face, and reducing the spectral range causes no decrease in the quality of the models developed using NIR spectra collected from transverse face. Partial lease square (PLS) modeling and test showed that calibrations developed using the visible and NIR spectra from transverse and longitudinal faces and calibrations developed by using the reducing spectral range (780–1050 nm) from the transverse face were moderate, and have a RPD range from 1.51 to 1.90. It is concluded that NIR spectroscopy can be used as an initial screening. __________ Translated from Journal of Northwest Forestry University, 2007, 22(5): 149–154 [译自: 西北林学院学报]     

Regeneration and reuse of exhausted solutions of electroless nickel plating wood veneer

The regeneration of exhausted solutions of electroless nickel plating wood veneer was realized using soluble calcium salt to precipitate and remove phosphite and then using fluoride to remove residual calcium ions from the solution. The effect of the pH value of the solution, treatment temperature and the molar ratio of calcium ions to phosphite ions on the removal efficiency of phosphite was investigated. Wood veneer was electroless plated using regenerated solutions. A coating with better electrical conductivity and electromagnetic shielding was obtained. __________ Translated from Journal of Northeast Forestry University, 2005, 33(3): 47–48 [译自: 东北林业大学学报, 2005, 33(3): 47–48]     

Role of canopy interception on water and nutrient cycling in Chinese fir plantation ecosystem

The role of canopy interception on nutrient cycling in Chinese fir plantation ecosystem was studied on the basis of the position data during four years. Results indicate that the average canopy interception amount was 267.0 mm/year. Canopy interception play a significant role in water cycle and nutrient cycle processes in ecosystem, and was an important part of evaporation from the Chinese fir plantation ecosystem, being up to 27.2%. The evaporation from the canopy interception was an important way of water output from ecosystem, up to 19.9%. The flush-eluviation of branches and leaves caused by canopy interception brought nutrient input of 143.629 kg/(hm² · year), which was 117.2% of the input 63.924 kg/(hm² · year) from the atmospheric precipitation. The decreased amount of 80.1 mm precipitation input caused by canopy interception reduced the amount of rainfall into the stand surface and infiltration into the soil, reduced the output with runoff and drainage, and decreased nutrient loss through output water. Therefore, the additional preserve of nutrient by canopy interception was 8.664 kg/(hm² · year). __________ Translated from Scientia Silvae Sinicae, 2006, 42(12): 1–5 [译自: 林业科学]     

Structure and characterization of Chinese fir (Cunninghamia lanceolata) wood/MMT intercalation nanocomposite (WMNC)

With water-soluble phenol-formaldehyde resin as an intermediate, Chinese fir (Cunninghamia lanceolata) wood/montmorillonite nanocomposite (WMNC) was prepared through vacuum impregnation and characterized with XRD, SEM, FTIR and TG-DTA analyses. The XRD analysis indicated that the wood crystallinity of WMNC decreased, the MMT exfoliated and some nano silicate layers entered into the non-crystallized microfibrillar region of the wood cell wall. Wood structure is anisotropic and its impregnation is anisotropic. Due to the nonuniformity of the MMT organic modification, PF intercalation and wood impregnation, the MMT configuration and distribution in wood were diverse. The SEM graphs of WMNC showed that some silicate grains were blocked in the wood cell lumen, some silicate layers adhered to the inner surface of the wood cell wall, and some exfoliated MMT layers even penetrated the wood cell wall. The obtained hydroxyl of WMNC increased and its ether linking decreased. It was considered that MMT and wood interacted not only with hydroxyl bonds, but also involved some chemical linking. Compared with untreated wood and the PF-impreg, the pyrolysis process of WMNC changed; its starting decomposing temperature decreased and its pyrolysis weight loss at high temperatures greatly decreased. The WMNC indicated certain nanoeffects of the composition of the inorganic MMT nanolamellae. __________ Translated from Journal of Beijing Forestry University, 2007, 29(1): 131–135 [译自: 北京林业大学学报]     

Niche of insect borers within Pinus massoniana infected by pine wood nematode

In November 2003 and June 2004, the insect borers and their spatial distribution within Pinus massoniana were investigated in Zhoushan City, in East China’s Zhejiang Province, where pine wood nematode (Bursaphelenchus xylophilus) are typically found. The niche width, proportional similarity of niche and the niche overlap of dominant species of dying trees were computed. Results show that five insect species infect and damage Pinus massoniana, which had been infected by pine wood nematodes, among which four are wood boring beetles and one termite. Species within host trees vary from winter to summer and all the species have their own niche width, proportional similarity of niche and the niche overlap. They can achieve competitive equilibrium and coexistence according to their biological characteristics and life habits. __________ Translated from Journal of Beijing Forestry University, 2005, 27(6): 108–111 [译自: 北京林业大学学报, 2005, 27(6): 108–111]     

Impact of heating speed on permeability of sub-alpine fir

Sub-alpine fir (Abies lasiocarpa (Hook)) is characterized by its low permeability and that it is then hard-to-dry. Long drying time for the species causes kiln capacity problems for numbers of spruce-pine-fir (SPF) lumber producers. A high-temperature drying schedule with a rapid rise in dry-bulb temperature to a temperature above boiling point at the beginning is a potential approach to enhance the drying productivity. Determinations in permeability of ten sub-alpine fir boards after slow heating and fast heating were carried out in this study. The results indicated that a rapid rise in temperature increased the permeability of sub-alpine fir. By statistical analysis, the permeability was increased significantly due to the fast heating in seven boards. The permeability in other three boards was also increased, but not significantly. Using a scanning electron microscope (SEM), the impact of heating speed on pit membrane of sub-alpine fir lumber was investigated. A small number of fine fractures were observed on the pit membrane after slow heating, while in case of fast heating, the torus was partially ruptured and a separation occurred in pit border and cell wall. By observing the SEM images, it was suggested that the force of vaporization and/or thermal stresses due to the fast heating were able to open the aspirated pits and/or break the membranes in the wood cells, and therefore increase the permeability, intensify the moisture transportability and improve the dry-ability of sub-alpine fir lumber.     

Mutual influences in growth and reproduction between pine wood nematode Bursaphelenchus xylophilus and bacteria it carries

The interactions between pine wood nematode and three bacterium strains isolated from the nematode, Bursaphelenchus xylophilus, which are two strong pathogenic bacterium strains, Pseudomonas fluorescens GcM5-1A and Pseudomonas putida ZpB1-2A and a weak-pathogenic bacterium strain, Pantoea sp. ZM2C, were studied. The result showed that the strong-pathogenic GcM5-1A strain and ZpB1-2A strain significantly increased fecundity, reproduction rate, and the body volume of the adult nematode. Meanwhile, pine wood nematodes significantly promoted reproduction of the two strong-pathogenic bacterium strains. However, the weak-pathogenic bacterium strain, ZM2C, completely inhibited reproduction of pine wood nematodes. Aseptic pine wood nematodes significantly inhibited reproduction of the strain ZM2C. The results indicated that mutualistic symbiosis exists between pine wood nematodes and the two pathogenic bacteria it carries. The phenomenon showed that the pathogenic bacteria carried by the nematode were not accidentally contaminated, but rather had existed as symbionts of the nematode with which it had coevoluted over a long period. The role of mutualistic symbiosis in the process of pine wilt disease was also discussed. __________ Translated from Journal of Nanjing Forestry University, 2005, 29(3): 1–4 [译自: 南京林业大学学报, 2005, 29(3): 1–4]     

Improvement of wood properties by urea-formaldehyde resin and nano-SiO2

In order to improve wood properties of triploid clones of Populus tomentosa, urea-formaldehyde (UF) resin was compounded with nano-SiO₂, coupling agents and flame retardants in different ways to prepare five kinds of modifiers. The poplar wood samples were impregnated with the modifiers and heated to prepare UF-SiO₂-wood composites. The antiswelling efficiency, resistance of water absorption, oxygen index and hardness of the composites were measured. Results show that all of the modifiers reduced water absorption of poplar wood and enhanced flame resistance and hardness. Nano-SiO₂ showed a marked effect in improving the hardness of wood. In addition, all of the modifiers, except UF-C-SiO₂-polymer, improved the dimensional stability of poplar wood. The UF resin and nano-SiO₂ compound improved general properties of poplar wood. __________ Translated from Journal of Beijing Forestry University, 2006, 28(2): 123–128 [译自: 北京林业大学学报]     

Hygrothermal effect of bamboo by dynamic mechanical analysis

Dynamic properties of bamboo, Phyllostachys pubescens, with moisture content (MC) ranging from −130 to 130°C, were studied by dynamic mechanical analysis (DMA). The results showed that the hygrothermal effect on dynamic mechanical properties was negative. The storage modulus decreases with increasing temperature and MC, and glass transition temperature decreases with increasing MC. The glass transition temperature and tan delta of bamboo were 30.5°C, 0.02 and 10.61°C, 0.04, when MC was 10% and 34%, respectively. __________ Translated from Journal of Nanjing Forestry University (Natural Sciences Edition), 2006, 30(1): 65–68 [译自: 南京林业大学学报(自然科学版), 2006, 30(1): 65–68]     

Effects of solid water and foliar fertilizer on survival and growth of seedlings in sand prevention and control

To promote afforestation in sandy lands and increase the effects of prevention and control of desertification, the application of a new drought-resistant product—solid water and foliar fertilizer “Shifengle”—was studied. A comparison of three treatments (solid water, foliar fertilizer, and control) showed that both solid water and foliar fertilizer increased plant survival rate by 10% and 18.2%, respectively. Afforestation survival rates of Salix psammophila and Hedysarum mongolicum reached over 90%. In addition, height and crown growth as well as biomass of seedlings were improved by the treatments. __________ Translated from Journal of Beijing Forestry University, 2006, 28(3): 76–80 [译自: 北京林业大学学报]     

Dynamic viscoelastic behavior of wood under drying conditions

In this study heartwood from a Chinese fir [Cunninghamia lanceolata (Lamb.) Hook] plantation was treated using a high-temperature drying (HTD) method at 115°C, a low-temperature drying (LTD) method at 65°C, and freeze vacuum drying (FVD), respectively. The dynamic viscoelastic properties of dried wood specimens were investigated. The measurements were carried out at a temperature range of −120 to 250°C at four different frequencies (1, 2, 5, and 10 Hz) using dynamic mechanical analysis (DMA). We have drawn the following conclusions: 1) the storage modulus E′ and loss modulus E″ are the highest for HTD wood and the lowest for FVD wood; 2) three relaxation processes were detected in HTD and LTD wood, attributed to the micro-Brownian motion of cell wall polymers in the non-crystalline region, the oscillations of the torso of cell wall polymers, and the motions of the methyl groups of cell wall polymers in the non-crystalline region in a decreasing order of temperatures at which they occurred; and 3) in FVD wood, four relaxation processes were observed. A newly added relaxation is attributed to the micro-Brownian motions of lignin molecules. This study suggests that both the HTD and the LTD methods restrict the micro-Brownian motion of lignin molecules somewhat by the cross-linking of chains due to their heating history. __________ Translated from Journal of Beijing Forestry University, 2008, 30(3): 96–100 [译自: 北京林业大学学报]     

Soil fractal features of subalpine coniferous forests in western Sichuan under different anthropogenic disturbances

Fractal theory, used to study natural figures and images with self-similarity but without characteristic lengths, offers an effective tool to investigate quantitatively the complex systems such as soil. In this paper, we have discussed about our study of the fractal features of the subalpine coniferous forests, soil particles, and microaggregates under different intensities of anthropogenic disturbances in the Miyaluo area of west Sichuan and investigated the effects of the disturbances on the forest soils attributed to different fractal dimensions. The study introduces a new way to investigate the recovery and reestablishment of subalpine coniferous forests. __________ Translated from Chinese Journal of Ecology, 2005, 24(8): 878–882 [译自: 生态学杂志, 2005, 24(8): 878–882]     

Import analysis of China’s major timber products in 2004

Timber import is an important and integral part of China’s timber trade. According to different kinds of product type, this paper analyzes its import in 2004 separately; based on the conditions of China’s timber import trade in 2004, this paper finds out some existing problems and puts forward corresponding countermeasures. __________ Translated from Journal of Beijing Forestry University (Social Sciences Edition), 2006, 5,(1) [译自: 北京林业大学学报(社会科学版), 2006, 5 (1)]     

Nonisothermal moisture movement in wood

In order to analyze the effect of temperature gradient on moisture movement during highly intensive drying, such as microwave-vacuum drying, the profile of the temperature and moisture content in sealed wood whose opposite faces were subjected to temperature gradient for a short time was measured. The ratio of the moisture content (MC) gradient to the temperature gradient (dM/dT) was calculated and the factors influencing moisture movement under nonisothermal conditions were discussed. The results indicate that moisture moved in wood from the warm surface to the cold one even if opposite faces of the sealed wood assembly were exposed continuously to different but constant temperatures for a short period. The moisture content on the cold surface was higher than that on the warm surface. The moisture content gradient opposite to the temperature gradient was established, and the dM/dT was below 0.9%/°C. The temperature in the sample and the distance from the hot surface of the sample was strongly linearly correlated. With an increase in temperature, initial moisture content and experimental time, the dM/dT was significantly increased. __________ Translated from Journal of Beijing Forestry University, 2005, 27(2): 96–100 [译自: 北京林业大学学报, 2005, 27(2): 96–100]     

Application of CITYgreen model in benefit assessment of Nanjing urban green space in carbon fixation and runoff reduction

Based on the analytical framework and calculation principles of the CITYgreen model to assess the benefits of urban green spaces in terms of carbon fixation and runoff reduction, an approach was made to obtain appropriate parameters for this model to calculate the ecological benefits of different urban land use types in the main city of Nanjing. The results indicate that carbon fixation benefits received by the main city of Nanjing is 5%–60% of that by natural forests on a per unit area basis. The ecological value of carbon fixation and runoff reduction of the Nanjing urban green space was about 177 million RMB in total. The ecological benefits of different land use types were in the order of green area > public facilities > residential areas > roads and squares > industrial areas > municipal utilities. This research can provide references for city planning and urban green space establishment and facilitate the popularization of quantitative assessment of ecological benefits of green spaces in Chinese cities. __________ Translated from the Chinese Journal of Applied Ecology, 2007, 18(6): 1293–1298 [译自: 应用生态学报]     

Profile of bordered pit aspiration in Cryptomeria japonica using confocal laser scanning microscopy: pit aspiration and heartwood color

Nine trees of Cryptomeria japonica from six elite tree clones with a broad range of heartwood colors were selected. The profiles of pit aspiration percentage (ASP) of earlywood and latewood from pith to bark for green and air-dry conditions were determined to study the relationship between heartwood color and pit aspiration. Confocal laser scanning microscopy (CLSM) observations showed that the ASP of earlywood was low in sapwood and high in heartwood in the green condition. Pit aspiration increased in intermediate wood when compared with sapwood. On the other hand, latewood pits did not aspirate during heartwood formation. Comparing the air-dry condition with the green condition, sapwood pits aspirated during drying in both earlywood and latewood; however, there was no significant difference in pit aspiration of heartwood. There was no significant difference between samples with red and black heartwoods for ASP. The difference in ASP between individual trees was larger than that by heartwood color. The general advantage of CLSM over light microscopy is that serial optical sections along the Z axis can be obtained for any moisture condition, without the need for thin sectioning or embedding.