Rapid liquid chromatographic determination of dimetridazole and ipronidazole in swine feed

A simple and rapid method is described for the determination of dimetridazole (DMZ) and ipronidazole (IPR) in swine feeds at various levels (0.11-110 ppm). The drugs are released from feed by prewetting with a buffer, followed by extraction with either methanol or methylene chloride, depending on the drug level; if necessary, an acid-base cleanup is used before the liquid chromatographic analysis. The analytes are separated on a C18 column and monitored at 320 nm for detection and quantitation. Recoveries of DMZ from several feed formulations averaged 108% at the 92.8 ppm level with a standard deviation (SD) of 4.00% and a coefficient of variation (CV) of 3.70%, 101% at the 11.2 ppm level with an SD of 11.9% and a CV of 11.8%, and 100% at the 0.112 ppm level with an SD of 9.27% and a CV of 9.25%. Recoveries of IPR averaged 77.1% at the 12.9 ppm level with an SD of 1.75% and a CV of 2.27%; IPR recoveries averaged 35.2% at the 0.129 ppm level with an SD of 3.39% and a CV of 9.63%.     

Analysis of fenhexamid in caneberry, blueberry, and pomegranate by liquid chromatography-tandem mass spectrometry

An analytical method for the determination of fenhexamid [N-(2,3-dichloro-4-hydroxyphenyl)-1-methylcyclohexanecarboxamide] in caneberry, blueberry, and pomegranate was developed utilizing acetone extraction, column cleanup, liquid-liquid partitioning, and liquid chromatography-tandem mass spectroscopy (LC-MS/MS) for detection. Method validation recoveries ranged from 91 to 96% for caneberry, from 80 to 91% for blueberry, and from 74 to 95% for pomegranate. Control samples collected from IR-4 trials for all matrixes had residue levels of <0.020 ppm. Fenhexamid-treated field samples had residue levels that ranged from 0.46 to 16.11 ppm (caneberry), from 0.87 to 2.91 ppm (blueberry), and from 1.59 to 1.85 ppm (pomegranate). The method was validated to a limit of quantitation of 0.020 ppm, and the limit of detection was 0.009 ppm.     

Liquid chromatographic determination of chlortetracycline hydrochloride in ruminant and poultry/swine feeds.

A liquid chromatographic (LC) method is described for the determination of chlortetracycline hydrochloride (CTC) in poultry/swine and ruminant feeds in the 10-100 ppm range and in premix. CTC is extracted from ground feed/premix with acidified acetone, and the extract is filtered through a Millex-HV filter or disposable C18 column. The filtrate is partitioned with methylene chloride when additional cleanup is necessary. A Nova-Pak C18 column is used for LC separation with determination at 370 nm. The average recovery of CTC from premix was 95% with a standard deviation (SD) of 1.70 and a coefficient of variation (CV) of 1.79%. The overall average recovery from feeds was 77% with an SD of 3.18 and a CV of 4.10%.     

Spectrofluorometric determination of histamine in fish and meat products

A method has been developed for spectrofluorometric determination of histamine in fish and meat products. After a perchloric extract is obtained from samples, histamine is extracted with n-butanol and transferred to hydrochloric acid. Finally, histamine is subjected to a condensation reaction with o-phthalaldehyde (OPT). The method was tested for lack of interference from other amines. Precision of the method in fish products was 6.60% CV; recovery was 96.50%. In meat products, precision was 5.42% CV; recovery was 96.20%. By analysis of variance (P = 0.05), no significant statistical differences were found for recovery values vs histamine content in both foods.     

Gas chromatographic-mass spectrometric method for the analysis of dimethomorph fungicide in dried hops

An analytical method for the determination of dimethomorph [(E,Z)-4-[3-(4-chlorophenyl)-3-(3,4-dimethoxyphenyl)acryloyl]morpholine] residues in dried hops was developed utilizing liquid-liquid partitioning, automated gel permeation chromatography (GPC), Florisil and aminopropyl solid phase extraction (SPE) column cleanups, and gas chromatography (GC) with mass selective detection (MSD). Method validation recoveries from dried hops ranged from 79 to 103% over four levels of fortification (0.1, 1.0, 5.0, and 20 ppm). Control and dimethomorph-treated hop samples collected from three field sites had residue levels of <0.10 and 4.06-17.32 ppm, respectively. The method was validated to the limit of quantitation at 0.10 ppm. The limit of detection for this method was 0.045 ppm.     

Analysis of pesticides in dried hops by liquid chromatography-tandem mass spectrometry

An analytical method was developed for the determination of eleven agrochemicals [abamectin (as B1a), bifenazate, bifenthrin, carfentrazone-ethyl, cymoxanil, hexythiazox, imidacloprid, mefenoxam, pymetrozine, quinoxyfen, and trifloxystrobin] in dried hops. The method utilized polymeric and NH2 solid phase extraction (SPE) column cleanups and liquid chromatography with mass spectrometry (LC-MS/MS). Method validation and concurrent recoveries from untreated dried hops ranged from 71 to 126% for all compounds over three levels of fortification (0.10, 1.0, and 10.0 ppm). Commercially grown hop samples collected from several field sites had detectable residues of bifenazate, bifenthrin, hexythiazox, and quinoxyfen. The control sample used was free of contamination below the 0.050 ppm level for all agrochemicals of interest. The limit of quantitation and limit of detection for all compounds were 0.10 and 0.050 ppm, respectively.     

Analysis of flonicamid and its metabolites in dried hops by liquid chromatography-tandem mass spectrometry

An analytical method was developed for the determination of the neo-nicotinoid insecticide flonicamid ( N-cyanomethyl-4-trifluoromethylnicotinamide) and its metabolites N-(4-trifluoronicotinoyl) glycine (TFNG), 4-trifluoronicotinic acid (TFNA), and 4-trifluoromethylnicotinamide (TFNA-AM) in dried hops. The method utilized C18 and polymeric solid phase extraction (SPE) column cleanups, liquid-liquid partitioning, and liquid chromatography (LC) with mass spectrometry (MS/MS). Method validation and concurrent recoveries from untreated dried hops ranged from 66 to 119% for all compounds over five levels of fortification (0.005, 0.02, 0.2, 2.0, and 4.0 ppm). Flonicamid-treated hop samples collected from three field sites had the following residues: flonicamid levels of 0.561-2.85 ppm, TFNA levels of 0.302-0.470 ppm, TFNA-AM levels of 0.038-0.177 ppm, and TFNG levels of 0.098-0.204 ppm. Untreated hop samples from all fields had residues <0.005 ppm for flonicamid, TFNA, TFNA-AM, and TFNG. The limit of quantitation and limit of detection for all compounds were 0.005 and 0.0025 ppm, respectively.     

Determination of sulfite in food by flow injection analysis

A method is described for the determination of sulfite levels in food products by flow injection analysis (FIA). The method is based on the decolorization of malachite green by SO2, which is isolated from the flowing sample stream by means of a gas diffusion cell. The FIA method has a detection limit in food sample extracts of 0.1 ppm SO2 (3 times peak height of blank), which corresponds to 1-10 ppm SO2 in a food product, depending on the extraction procedure used. At the 5 ppm SO2 level in a food extract, the precision of replicate injections is +/- 1-2%. The method was tested on a variety of both sulfite-treated and untreated food products and the results compared favorably with those obtained by the Monier-Williams, colorimetric (pararosaniline), and enzymatic (sulfite oxidase) methods. The average differences from the FIA results were 19, 11, and 12%, respectively, for those samples (n = 12) above 50 ppm SO2. At lower levels the results were somewhat more erratic due to inaccuracies of the various methods at low concentrations.     

Atomic absorption spectrophotometric determination of chromium in foods

A method is reported for determination of chromium in foodstuffs. Organic matter is digested with nitric acid, followed by oxidation to Cr(VI) and extraction with methyl isobutyl ketone (MIBK) after HCl addition. Chromium determinations are performed by flame absorption spectroscopy. Absence of interferences is verified and recovery tests are performed on food samples. Quantitation limit (3.8 ng/mL), accuracy (NBS Standard Reference Material 1,573 Tomato Leaves, 4,500 +/- 500 ng/g, found 3,860 +/- 409 ng/g), and precision (CV for vegetable matrix = 9.05%, CV for animal matrix = 14.95%) of the procedure are evaluated.     

Liquid chromatographic determination of tetracycline residues in animal feeds

A liquid chromatographic method for the multiresidue determination of tetracyclines (TCs) in feeds is described. The levels of quantitation were 10 ppm each for tetracycline-HCl (TC), oxytetracycline (OTC), and chlortetracycline-HCl (CTC); the detection limit was 40 ppb for each. The calibration curves were linear between 2.5 and 100 ppm. The procedure involved double extraction with pH 2.0 and pH 4.5 McIlvain buffers, cleanup on a Sephadex LH-20 column, separation on a Nova-Pak C18 column, and detection at 370 nm. Recoveries of 10 micrograms/g of each TC in multiresidue feed samples ranged from 55.8 to 75.5% for OTC, 71.6 to 100% for TC, and 22.4 to 60.6% for CTC. The identities of the TCs were confirmed by thin layer chromatography.     

Gas chromatographic determination of pentachlorophenol in gelatin

A method is described for the determination of pentachlorophenol (PCP) in gelatin. The method employs acid and heat to hydrolyze the gelatin matrix, a base partition and wash for separation and cleanup, and a reacidification and extraction with hexane for direct determination of PCP, without preparation of a derivative, using gas chromatography (GC) with a 1% SP- 124ODA liquid phase and a 63Ni electron capture detector. Recoveries averaged 106% for fortifications between 0.02 and 1.0 ppm. The limit of quantitation is 20 ppb. The limit of detection is 4-6 ppb. The method, which has undergone a successful intralaboratory trial, is simple and rapid, and requires only general laboratory reagents and equipment. GC of the acetate derivative of PCP is used for confirmation of identity.     

Determination of bisphenol A in food-simulating liquids using LCED with a chemically modified electrode

Liquid chromatography with electrochemical detector (LC-ED), using a chemically modified electrode coated with a metalloporphyrin film, is reported for determination of bisphenol A (BPA) migration from polycarbonate baby bottles. The extraction process of the samples was performed according to regulations of the Southern Common Market (MERCOSUR), where certain food-simulating liquids [(A) distilled water, (B) acetic acid 3% V/V in distilled water, and (C) ethanol 15% V/V in distilled water] are defined along with controlled time and temperature conditions. The baseline obtained using the naked electrode showed a considerable drift which increased the detection limit. This effect was suppressed with the chemically modified electrode. A linear range up to 450 ppb along with a detection limit of 20 ppb for the amperometric detection technique was observed. The procedure described herein allowed lowering the detection limit of the method to 0.2 ppb. The value found for BPA in the food-simulating liquid is 1.2 ppb, which is below the tolerance limit for specific migration (4.8 ppm).     

Beta-cyclodextrin post-column fluorescence enhancement of aflatoxins for reverse-phase liquid chromatographic determination in corn

beta-Cyclodextrin enhances the fluorescence of aflatoxins B1 and G1 in aqueous systems. This effect was utilized in developing a unique reverse-phase liquid chromatographic (LC) method for determination of aflatoxins B1, B2, G1, and G2 (B1 detection limit 1 ppb), without preparing derivatives of B1 and G1. The aflatoxins are dissolved in methanol or the mobile phase for injection onto the LC system. Using a mobile phase of methanol-beta-cyclodextrin (1 + 1), the aflatoxins are resolved on a C18 column. Fluorescence of the aflatoxins is enhanced by post-column introduction of an aqueous concentrated beta-cyclodextrin solution. All 4 aflatoxins elute within 10 min in the order G2, G1, B2, B1. Fluorescence responses for B1 and G1 standards were linear over the concentration range 0.5-10 ng, yielding correlation coefficients (r) of 0.9989 and 1.000, respectively. The average peak response ratio for G1:B1 for the mobile phase-enhancement solution described was 0.765 with a coefficient of variation (CV) of 0.98%. CVs were 6.2, 9.0, and 7.5% for multiple assays of aflatoxin B1 in 3 samples of naturally contaminated corn. For samples of corn spiked to a total B1 content of 8.3 ng/g, average B1 recovery was 90% (CV 11.7%).     

Determination of ethylene oxide in ethoxylated surfactants and demulsifiers by headspace gas chromatography

A headspace gas chromatographic method for the determination of traces of ethylene oxide in ethoxylated surfactants and demulsifiers was developed. Samples are analyzed directly by the technique to a 1.0 ppm (w/w) quantitation limit. The procedure also performs well for propylene oxide, acetaldehyde, and 1,4-dioxane. It is simple, sensitive, and linear. The percent relative standard deviations for 0.5 and 30 ppm ethylene oxide in the surfactant were 2.8 and 8.3%, respectively.     

Gas chromatographic determination of residue levels of the herbicides trifluralin, benefin, ethalfluralin, and isopropalin in soil with confirmation by mass selective detection

A method is presented for the simultaneous or individual determination of the dinitroaniline herbicides trifluralin, benefin, ethalfluralin, and isopropalin in soil. The herbicides are extracted with acetonitrile-water (99 + 1), and the extracts are purified with small, disposable Florisil cartridges prior to analysis by gas chromatography using an electron capture detector or a mass selective detector. When electron capture detection is used as the primary detection system, confirmation with selective detection can be obtained using gas chromatography-mass spectrometry with a mass selective detector and a capillary column operated in the split mode. The limit of detection is 0.01 ppm, and recoveries averaged 95-112% for the 4 herbicides in several different soil types fortified at levels of 0.01-0.33 ppm.     

Residue analysis of glyphosate and its principal metabolite in certain cereals, oilseeds, and pulses by liquid chromatography and postcolumn fluorescence detection.

A postcolumn liquid chromatographic method to determine the extractable residues of glyphosate (GLYPH) and its principal metabolite, (aminomethyl)phosphonic acid (AMPA), in various cereals and beans is described. The finely ground sample is extracted with a mixture of chloroform and water, and the resulting aqueous layer is passed through a cation exchange column. The eluate is adjusted to pH 7-10 and passed through an anion exchange column. The second column is eluted with 0.3M HCl solution and the resulting acidic eluate is analyzed with liquid chromatography coupled with postcolumn fluorescence detection. The mean recoveries for GLYPH in barley, canola, dry pea, flax, soybean, wheat, and white bean ranged from 90.0 to 98.1%, with coefficients of variation (CV) from 2.9 to 10.0% and limits of detection (LOD) from 0.07 to 0.14 ppm. Similarly, mean recoveries for AMPA in the same crops ranged from 87.4 to 98.9%, with CV from 4.6 to 7.7 and LOD from 0.05 to 0.12 ppm. Using this method, an analyst can routinely analyze 6 samples per 1.5 days. The advantages of this procedure are discussed.     

Determination of phenol in honey by liquid chromatography with amperometric detection

A sensitive, selective analytical method has been developed for determination of phenol in honey by liquid chromotography (LC) with amperometric detection (AMD). Phenol is extracted with benzene from the distillate of honey. The benzene extract is washed with 1% sodium bicarbonate solution and then reextracted with 0.1N sodium hydroxide followed by cleanup on a C18 cartridge. Phenol is determined by reverse-phase LC with amperometric detection. An Inertsil ODS column (150 X 4.6 mm, 5 microns) is used in the determination. The mobile phase is a mixture (20 + 80 v/v) of acetonitrile and 0.01M sodium dihydrogen phosphate containing 2mM ethylenediaminetetraacetic acid, disodium salt (EDTA) with the pH adjusted to 5.0. The flow rate is 1 mL/min under ambient conditions. The applied potential of the AMD using a glassy carbon electrode is 0.7 V vs an Ag/AgCl reference electrode. Average recoveries of phenol added to honey were 79.8% at 0.01 ppm spiking level, 90.4% at 0.1 ppm, and 91.0% at 1.0 ppm. Repeatabilities were 3.4, 1.3, and 1.8%, respectively. The detection limit of phenol in honey was 0.002 ppm. For analysis of 112 commercial honey samples, the range and average values of 32 detected samples were 0.05-5.88 ppm and 0.71 ppm, respectively.     

Liquid chromatographic determination of spiramycin residues in chicken tissues

A liquid chromatographic (LC) method is described for determination of spiramycin residues in chicken muscles. The drug is extracted from muscles with acetonitrile, the extract is concentrated to 3-4 mL and rinsed with n-hexane followed by ethyl ether, and the drug is extracted with chloroform. LC analysis is carried out on a Zorbax BP-C8 column, and spiramycin is detected spectrophotometrically at 231 nm. Recoveries of spiramycin added to chicken muscles at 0.2 and 0.1 ppm were 93.9 and 89.0%, respectively. The detection limit was 5 ng for spiramycin standard, and 0.05 ppm in chicken muscles.     

Capillary gas chromatographic determination with electron capture detector of beta-propiolactone in biological materials

A method has been developed for the determination of beta-propiolactone by derivatizing it to the volatile N-hexyl-3-heptafluorobutanoyloxypropanamide, which can be separated and identified by a capillary CP-Sil 8 column, and detected by an electron capture detector (ECD). First, beta-propiolactone is reacted with N-hexylamine to yield N-hexyl-3-hydroxypropanamide. The fluorobutanoyl ester derivative is next prepared by using heptafluorobutyric acid anhydride in the presence of trimethylamine. The method is very sensitive, simple, and specific, and can be used to detect and quantitate residual beta-propiolactone in lyophilized biological materials. The limit of detection is 0.2 ppm beta-propiolactone in a 50 mg sample; however, because of variability at low levels, the limit of quantitation is 1 ppm. Detector response was linear for 2-500 mg beta-propiolactone. Recoveries were 98% or greater from lyophilized vaccines spiked at the 2-20 ppm level. No side products or interference peaks were observed in the derivatization reaction.     

Determination of ampicillin residues in fish tissues by liquid chromatography

A liquid chromatographic (LC) method is described for determination of ampicillin residues in fish tissues. The drug is extracted from tissues with methanol, and the extract is evaporated to dryness. This residue is cleaned up by Florisil cartridge chromatography. LC analysis is carried out on a Nucleosil C18 column, and ampicillin is quantitated by ultraviolet detection at 222 nm. Recoveries of ampicillin added to tissues at levels of 0.2 and 0.1 ppm were 73.2 and 61.5%, respectively. The detection limit was 3 ng for ampicillin standard, and 0.03 ppm in tissues.