The effect of brown-rot decay on water adsorption and chemical composition of Scots pine heartwood

? The effect of brown-rot (Coniophora puteana) decay on the water adsorption capacity and concentration of extractives of Scots pine (Pinus sylvestris L.) heartwood were studied by comparing corresponding properties of decayed and undecayed wood samples.

? The samples derived from 39 felled trees having a large between-tree variation in the extractive concentrations, and subsequently in the mass loss in the decay test. The water adsorption capacity, expressed as equilibrium moisture content (EMC), was measured at a high relative humidity (RH ～100%, 21 °C).

? In contrast to the widely held belief, the water adsorption capacity of brow-rotted heartwood appeared to be significantly higher than that of undecayed heartwood.

? The chemical composition of heartwood was changed radically by the fungus: the concentration of stilbenes, resin acids and free fatty acids decreased, while the concentration of soluble sugars increased as a result of decay. In addition, fungal sugars were found in the decayed samples. The concentration of total phenolics increased, which obviously reflected chemical changes in cell wall constituents other than extractives.

? As a conclusion, the information concerning the hygroscopicity of brown-rotted wood might be valuable e.g. when carrying out repairs on buildings damaged by advanced decay.

     

Measuring wood density by means of X-ray computer tomography

? Wood density is a characteristic of major interest. Usually, it is used as an indicator of wood quality; however, in the context of global change, it is increasingly used for biomass and carbon storage estimations. X-ray computer tomography is a method which enables quick estimates of wood density after applying a calibration procedure.

? A review of the literature is presented in this article. Most of the previous studies have been performed in the 80’s or at the beginning of the 90’s.

? In this study, the relationship between wood density and Hounsfield numbers was investigated using a recent medical scanner. A linear relationship was fitted using a calibration data set which consisted in tropical wood samples representing a large range of densities ranging between 133 and 1319 kg m^?3, and then validated using an independent data set (mainly temperate tree species). The fitted relationships were very strong (R ² > 0.999), whichever the tested scanner settings, with slight but significant effects of the current voltage and reconstruction filters. The RMSE values computed from the validation data set ranged between 5.4 and 7.7 kg m^?3 for densities ranging between 364 and 821 kg m^?3.

? In conclusion, this method of calibration enables the use of a medical scanner to obtain maps of wood density, in a fast and non destructive way, and with a very good accuracy. Very interesting perspectives are opened regarding biomass distribution within trees.

     

Methodology to assess both the efficacy and ecotoxicology of preservative-treated and modified wood

? Wood used in outdoor conditions out of ground contact is susceptible to weathering, inducing both fungal decay and leaching of components to the environment.

? This paper presents a methodology to determine these two parameters for untreated, preservative-treated and modified wood. Therefore, the wood was first leached and subsequently exposed to fungal decay of the most prominent wood-rotting fungi. The crustacean Daphnia magna was exposed to the leachates to provide information on their impact on the environment.

? Combining both parameters reveals that preservative-treated wood and modified wood are capable of protecting the wood adequately for application under use class 3 conditions without posing a threat to the environment.

? This proves the suitability of the concept of combining efficacy and ecotoxicology for the evaluation of new types of wood treatments.

     

Effects of site on fibre, kraft pulp and handsheet properties of Eucalyptus globulus

? Eight-year old trees from two Eucalyptus globulus Labill. clones planted across three different sites in Tasmania, Australia, were sampled for wood and kraft pulp/handsheet properties.

? Site had a significant effect on all measured properties. Compared with the poor site (Parkham) the wood from the good site (West Ridgley) had on average 11 % lower wood density. The poor site had also greater microfibril angles, shorter fibres at lower pulp yields.

? The handsheets produced with pulp from the poor site resulted in comparatively higher bulkiness, lower burst, lower tear and tensile indices, lower zero span tensile strength, but higher opacity, higher light scattering and higher surface roughness. Significant height effects were found with all wood properties, and also with tear index, zero span tensile strength and opacity.

? Discriminant analysis showed that for 76 out of 100 handsheets the raw material source, i.e. growth site, could be predicted correctly using a set of handsheet properties with tear index and bulk index being most prominent.

? This is unique evidence that site conditions are strongly reflected in handsheet properties produced from Eucalyptus pulp.

     

Non-destructive monitoring of early stages of white rot by Trametes versicolor in Fraxinus excelsior

? Non-destructive detection of fungal decay in living trees is relevant for forest management of valuable species, hazard tree assessment, and research in forest pathology. A variety of tomographic methods, based on stress wave timing, radioactive radiation, or electrical resistivity have been used to detect decay in standing trees non-destructively. But apart from mobile gamma ray computed tomography (Habermehl and Ridder, 1993) which is virtually unavailable, the detection of incipient stages of decay is still not possible.

? Wood moisture and electrolyte content influence the electric resistivity of wood. Both are changed by fungal decay. Therefore electric resistivity tomography (ERT) should detect decay in its early stages. Then it could be used to monitor the spatial and temporal progress of degradation.

? We infected four Fraxinus excelsior trees with Trametes versicolor using wooden dowels and measured two-dimensional electric resistivity tomograms 3, 10, 13 and 21 months after infection. Immediately after the last electric resistivity measurement trees were felled for further analyses of stem cross-sections. Wood moisture content and raw density had significantly increased in infected areas, but dry density had not significantly changed after 21 months. Areas of very low electric resistivity around the infected wounds correlated very well with infected wood in the stem cross-sections. Increasing areas of low electric resistivity around the infected wounds during consecutive measurements indicate increasing areas of infected wood.

? We conclude that the growth of white rot by Trametes versicolor can be monitored with electric resistivity tomography (ERT) beginning from incipient stages, even before wood density decreases. ERT could therefore be a powerful research tool for decay dynamics as well as a method for diagnosing wood decay in forestry and arboriculture.

     

Effect of extractives on conferred and natural durability of Cupressus lusitanica heartwood

? Identification of extractives present in Cupressus lusitanica heartwood has been conducted using GC-MS analyses. The chromatogram of toluene/ethanol extracts indicated the presence of large amounts of benzaldehyde and numerous terpenic compounds such as cedrol, agathadiol, epimanool, bornyl acetate, α-cedrene and β-cedrene.

? The effect of these extractives on the natural durability of cypress wood was investigated on heart wood blocks exposed to pure culture of Poria placenta before or after solvent extraction. Weight losses revealed severe fungal degradations on the extracted blocks compared to unextracted ones.

? Efficiency of heartwood extractives as inhibitors of the growth of Poria placenta on malt/agar test confirms their contribution to cypress natural durability.

? Cypress blocks were treated at 240 °C for different times to reach different levels of thermodegradation to evaluate effect of heat treatment on fungal durability. Results indicate that evaporation of volatile extractives during the first few minutes of heat treatment contribute to decreased wood durability, while longer treatment times lead to the expected improvement of durability.

? This study suggests that the content of extractives, which may be modified during wood drying or weathering processes, could be the origin of the conflicting data described in the literature concerning cypress natural durability.

     

Evaluation of decay resistance of wood products made from borax-impregnated wood and bonded with a formaldehyde-free cornstarch and tannin adhesive

? At present, the production of wood composites mainly relies on the petrochemical-based and formaldehyde-based adhesives such as phenol-formaldehyde (PF) resins and urea-formaldehyde (UF) resins, which are non-renewable and therefore ultimately limited in supply.

? This paper concerns the decay resistance of wood products bonded with a new, environment-friendly adhesive derived from abundant and renewable cornstarch and tannin. To improve the total resistance of the composite against both Coriolus versicolor and Coniophora puteana rot fungi, borax (di-sodium tetraborate) was added in proportions of 0.5%, 1% and 2% (w/w) to the cornstarch-tannin adhesives.

? The results show that increasing the concentration of borax in the adhesive decreased the mechanical properties of the composite. The best way to avoid this problem was to use wood impregnated with borax.

? Biodegradation studies were conducted on new composites, first without any treatment, followed by borax at 0.5% aqueous solution treatment. The results show that wood impregnated with borax, in the presence of tannin and sodium hydroxide in the adhesive improves the total resistance of the wood composite against both Coriolus versicolor and Coniophora puteana rot fungi.

     

Variation in the decay resistance of larch to fungi

? Decay resistance of larch (Larix sp.) to fungi was evaluated on heartwood samples belonging to 3 species (L. decidua, L. kaempferi and their hybrid), 3 races of European larch (polonica, sudetica and alpine), 13 wood lots (populations) and 313 trees.

? Larch wood appeared, on average, as moderately durable although a high variability was observed. At the sample level as well as at the mean individual tree level, durability ranged from class 1 to 5 according to EN 350-1 standard. At the population level, larch wood varied from ‘durable’ to ‘slightly durable’. Genetics played a major role in decay resistance at the species, provenance and tree levels. Environmental factors such as the position of heartwood samples and the age of trees were also identified as a source of variability.

? The most durable wood was not necessarily from old native alpine stands of European larch: some young larches from faster growing lowland origins also produced durable wood.

? Genetic improvement of larch wood durability appeared therefore likely by the selection of the best populations for decay resistance as well as from the selection of individuals.

     

Physical properties of wood in thinned Scots pines (Pinus sylvestris L.) from plantations in northern Spain

? The physical properties of wood and the associated variations within and between trees were evaluated by analysing 770 small specimens of clear wood from 11 Pinus sylvestris L. trees thinned from 3 plantations.

? Within-tree variations in basic density or volumetric shrinkage increased with cambial age and decreased with increasing ring width. The effect of the height in the stem on wood properties was considered indirect and height was not included as an explanatory variable in the mixed models proposed to estimate basic density and volumetric shrinkage.

? The models had random components for the intercept parameter and explained 52.5% of the total variance in basic density and 56% of the total variance in volumetric shrinkage. Linear shrinkage in the direction of the grain was extremely variable.

? Between-tree variation and between-plot variation in the physical properties of wood were high, considering that all trees sampled were growing in similar sites and stands. It would then be desirable to predict physical properties of wood on living trees in order to use the quality of wood as a criterion for timber tree selection in thinnings.

     

Ranking larch genotypes with the Rigidimeter: relationships between modulus of elasticity of standing trees and of sawn timber

? Direct assessment of modulus of elasticity (MOE) on standing trees is attractive for breeders to evaluate genotypes prior to selection: this can be done using the Rigidimeter, a bending-based measurement device.

? In this study, we tested its reliability to properly rank genotypes by relating trunk MOE with MOEs estimated with a vibrating analysis system (Bing) on different types of conditioned wood specimens from the same trees (boards and standardised 2×2×30 cm-clear-wood specimens). One hundred and ten trees from different genotypes of hybrid larch (Larix × eurolepis) were tested.

? Mean trunk MOE was 7 300 MPa with a similar value obtained for sawn boards. Clear-wood specimens MOE increased from pith to bark from less than 6 000 MPa to nearly 9 000 MPa. Moderate correlations (r = 0.48–0.61) were found at the individual tree level between trunk MOE and MOE of wood samples.

? Single specimen MOE was shown to be strongly related to a linear combination of trunk MOE and sample position.

? At the genotype mean level, trunk MOE was highly correlated with wood samples MOE (r = 0.80–0.91). Ranking of genotypes based on trunk MOE was mostly consistent with that based on standardised specimens.

? It was concluded that besides other operational advantages which are discussed, the Rigidimeter is a valuable tool for breeders to routinely evaluate and rank genotypes for stiffness prior to further selection.

     

Diminished vessel diameter as a possible factor in the decline of European ash (Fraxinus excelsior L.)

? The aim of this work was to examine the anatomy and functioning of secondary xylem in stems in relation to the decline of European ash (Fraxinus excelsior L.).

? We tested the hypothesis that declining trees show changes in the structure of wood, which result in impaired water transport.

? Anatomical analyses were carried out on wood samples (comprising all annual rings formed during the 30 years life of the analysed trees) collected at breast height from the main stem of healthy, weakened and dead ash trees. The width of annual wood increments, the diameter and density of earlywood vessels were measured and the theoretical hydraulic conductivity index through the secondary xylem calculated by application of Hagen-Poisseuille’s formula.

? Anatomical characteristics changed both with the age of trees and in response to unfavorable factors. The largest vessels were observed in healthy trees, which implied that they had the highest hydraulic conductivity index, whereas trees considered to be in decline produce smaller vessels and hence had reduced conductivity.

     

Variation in the natural termite resistance of teak (Tectona grandis Linn. fil.) wood as a function of tree age

? Tree age is one of the most important factors to affect the natural durability of wood.

? The purpose of this study was to determine the natural termite resistance of heartwood and sapwood of teak (Tectona grandis Linn. fil.) for trees aged 8, 30 and 51 years. Reticulitermes speratus Kolbe was employed as a test termite using a no-choice feeding method.

? The heartwood and sapwood of all of the trees tested exhibited antitermitic activity. Based on the mean mass loss due to termite activity, the sapwood and heartwood regions of 8-year-old trees are the most susceptible to termites while the heartwood regions of the 30-year-old trees showed termite resistance similar to the termite resistance of 51-year-old trees.

? The mass loss is moderately correlated with n-hexane extractive content, total extractive content, brightness and redness of the wood.

     

Colour and decay resistance and its relationships in Eperua grandiflora

? Eperua grandiflora, which is widely distributed in the French Guiana forest region, shows high variability in decay resistance. Further information concerning this wood quality parameter is necessary, but standard testing methods are complex and time-consuming. We assessed the use of colorimetry to determine durability in heartwood samples from a range of trees.

? Eperua grandiflora colour parameters were measured using a CIELAB system, revealing that the tree effect was greater than the radial position and height effects.

? The wood samples were exposed to Coriolus versicolor and Antrodia sp. according to two European standards (En 350-1 and XP CEN TS 15083-1). Eperua grandiflora is more susceptible to brown rot. These two standards did not give the same durability classes. The high variation in natural durability was due to the tree effect.

? These two properties were found to be correlated and the assessment also distinguished the extreme durability classes but they are not sufficient to classify the class of durability of this species.

     

Potential contribution of organosilicon compounds to reduced leaching of biocides in wood protection

? Leaching of biocide treated wood leads to reduced effectiveness and potential threat to the environment.

? Therefore the effectiveness of organosilicons as protective systems of biocides was evaluated. Scots pine sapwood specimens were impregnated with solely organosilicons and biocides as well as with combinations of both.

? The biocides 3-iodo-2-propynylbutylcarbamate, propiconazole and 3-(trimethoxysilyl)propyldimethyloctadecyl ammonium chloride confirmed their effectiveness regardless the addition of an organosilicon. Low leachate toxicities to the crustacean Daphnia magna were found for the organosilicons, whereas significant leachate toxicities were measured for the biocides. Combining both did not considerably diminish the leachate toxicities.

? It must therefore be concluded that under the circumstances as described in this article, organosilicons do not interfere with the efficacy of the biocides, but they do not contribute to a reduced leaching of the biocides either.

     

Rapid prediction of shrinkage and fibre saturation point on teak (Tectona grandis) wood based on near-infrared spectroscopy

? Dimensional stability, along with the natural durability and colour of the wood, is one of the most important characteristics of teak used as timber. However, it is very time-consuming to take measurements of this kind. For the purposes of selection for the production of improved varieties, the number of samples to be measured rapidly exceeds the capacity of a traditional laboratory.

? Near-infrared spectroscopy, based on a set of reference data, is a tool enabling many of the chemical properties of wood to be predicted and the number of laboratory measurements to be reduced exponentially. The issue here is a question of checking the effectiveness of NIRS tool to build models and predict the shrinkage and fibre saturation point of teak wood from Togo.

? The results show the possible use of NIRS to measure the dimensional stability of teak wood and that it is appropriate to choose the type of wood and type of surface to be measured by NIRS. The best prediction models for radial and tangential shrinkage and fibre saturation point give R ² values of 0.72, 0.83 and 0.87 respectively with ratios of performance deviation of 1.8, 2.4 and 2.8.

? Consequently, after verification on other sets of teak samples, which may or may not be included in the prediction model, NIRS can be used to predict shrinkage and fibre saturation point values accurately for a large number of samples, making it possible to include these characteristics in the selection criteria for classifying wood and high throughput phenotyping.

     

Genetic variation in wood density and correlations with tree growth in Prosopis africana from Burkina Faso and Niger

? Variation in wood basic density and its correlation with tree growth were investigated at 13 years in a provenance/progeny test of Prosopis africana in Niger. The test included progeny from 256 trees sampled from 24 provenances in the Sahelian ecozone of Burkina Faso and Niger.

? Variation in wood density was significant due to provenances and families within provenances. Individual tree heritability was higher for wood density than for growth traits. Provenance means for wood density increased from the more humid to the drier parts of the sample region. Phenotypic correlations indicated that larger trees tended to have denser wood.

? Clines suggest that natural populations of P. africana from the drier parts of the sample region have the genetic capacity to produce denser wood, compared with populations from the more humid parts of the region. Correlations and heritability estimates suggest that selection of faster-growing trees may produce a small gain in wood volume but little (if any) gain in density in the subsequent generation. Multi-location provenance/tests are needed to confirm this tentative conclusion.

     

Genetic correlations among juvenile wood quality and growth traits and implications for selection strategy in Pinus radiata D. Don

? Juvenile wood quality in Pinus radiata is affected by factors such as low density, stiffness, and high microfibril angle, spiral grain, and shrinkage. Adverse genetic correlations between growth and wood quality traits remain as one of the main constraints in radiata pine advanced generation selection breeding program.

? Juvenile wood property data for this study were available from two progeny tests aged 7 and 6 y. We estimated the genetic correlations between stiffness, density, microfibril angle, spiral grain, shrinkage in the juvenile core and DBH growth in radiata pine, and) to evaluated various selection scenarios to deal with multiple objective traits.

? Negative genetic correlations were found for modulus of elasticity (MoE) and density with microfibril angle, spiral grain, shrinkage, and DBH. We observed low to moderate unfavourable genetic correlations between all wood quality traits and DBH growth.

? These low to moderate genetic correlations suggest that there may be some genotypes which have high DBH growth performance while also having high wood stiffness and density, and that the adverse correlation between DBH and MoE may not entirely prohibit the improvement of both traits. Results indicate that, in the short term, the optimal strategy is index selection using economic weights for breeding objective traits (MAI and stiffness) in radiata pine.

? In the long-term, simultaneously purging of the adverse genetic correlation and optimizing index selection may be the best selection strategy in multiple-trait selection breeding programs with adverse genetic correlations.

     

A Linking Test that establishes if groundwater recharge can be determined by optimising vegetation parameters against soil moisture

? The impact of afforestation/deforestation on groundwater recharge can be predicted by using one-dimensional soil-vegetation water flow models based on Richards’ equation. However simulations depend upon parameters that are not easily measurable.

? Pollacco et al. (2008) showed that the hydraulic parameters can be determined, if the vegetation parameters are known, by fitting simulated time series of soil moisture profiles to those measured in situ. This paper presents a case study to determine if the interception and crop factor parameters can tentatively be calibrated by fitting soil moisture profiles. Synthetic data were used and the other vegetation parameters and the soil hydraulic parameters were assumed to be known.

? We applied and improved the Linking Test developed by Pollacco et al. (2008) to look for links between the parameters that need to be calibrated, and thus to investigate whether inverse modelling is feasible, which depends on the accuracy of the calibration data.

? The Linking Test established that interception and evapotranspiration parameters are linked and, therefore, uncertainty on interception compensates for uncertainty on evapotranspiration. Thus in spite of a good match between observed and simulated soil moisture data, inverse modelling is unfeasible. This is true even if the interception or the crop factor parameters are known, because an error on interception or evapotranspiration will be compensated by an error on groundwater recharge without affecting soil moisture.

? This paper recommends that vegetation parameters should not be calibrated by optimisation against soil moisture data.

     

Productivity of temperate broad-leaved forest stands differing in tree species diversity

? Understanding the effects of tree species diversity on biomass and production of forests is fundamental for carbon sequestration strategies, particularly in the perspective of the current climate change. However, the diversity-productivity relationship in old-growth forests is not well understood.

? We quantified biomass and above-ground production in nine forest stands with increasing tree species diversity from monocultures of beech to stands consisting of up to five deciduous tree species (Fagus sylvatica, Fraxinus excelsior, Tilia spp., Carpinus betulus, Acer spp.) to examine (a) if mixed stands are more productive than monospecific stands, (b) how tree species differ in the productivity of stem wood, leaves and fruits, and (c) if beech productivity increases with tree diversity due to lower intraspecific competition and complementary resource use.

? Total above-ground biomass and wood production decreased with increasing tree species diversity. In Fagus and Fraxinus, the basal area-related wood productivity exceeded those of the co-occurring tree species, while Tilia had the highest leaf productivity. Fagus trees showed no elevated production per basal area in the mixed stands.

? We found no evidence of complementary resource use associated with biomass production. We conclude that above-ground productivity of old-growth temperate deciduous forests depend more on tree species-specific traits than on tree diversity itself.

     

High resolution temporal variation in wood properties in irrigated and nonirrigated Eucalyptus globulus

? Environmental determinants of wood properties variation were examined in Eucalyptus globulus, a globally important hardwood plantation species, in southern Tasmania, Australia.

? Radial variation in wood properties, measured with the SilviScan system, were re-scaled from distance to time abscissa using stem radial growth data measured with dendrometers. With this re-scaled data it was possible to evaluate how water availability and temperature affected wood density, microfibril angle (MFA) and fibre and vessel transverse dimensions in irrigated and non-irrigated trees.

? Wood density, fibre radial diameter and MFA were sensitive to water availability. Wood density increased and fibre radial diameter decreased in response to reduced water availability. When high water availability was maintained, wood density was negatively correlated with temperature. Together, temperature and soil matric potential explained about 60% of temporal variation in wood density variation. In contrast MFA was not related to temperature but decreased with increasing water stress. Slower growing trees also had lower MFA than faster growing trees. Slower growing trees had a larger number of vessels per unit area of wood than faster growing trees within this even aged stand. However, vessel radius to the 4th power was significantly higher in faster growing trees than in slower growing trees.

? Overall, E. globulus wood properties were sensitive to temporal changes in environmental conditions (particularly water availability) and associated growth rates. The data provided support for the hypothesis that growth rates are hydraulically mediated.