Preparation and characterization of wood/montmorillonite nanocomposites

With montmorillonite (MMT) organically modified as organophilic MMT (OMMT) and water-soluble phenol formaldehyde resin (PF) as intermediate, Chinese fir (Cunninghamia lanceolata) wood/MMT nanocomposites (WMNC) were prepared via nano intercalation compounding and characterized by XRD, SEM and FTIR. Results show that: 1) the preparation of OMMT is very successful; 2) the self-made PF can effectively intercalate into MMT to increase markably its gallery distance and even exfoliate its nano silicate laminae; 3) the XRD analysis indicates that some exfoliated MMT enters the non-crystallized region of microfibrils in wood cell walls and the crystallinity degree of wood in WMNC decreases; 4) the SEM graphs show that multiform MMT exists in WMNC. Some grains block in wood cell lumen, some layers adhere to the wood surface of the inner cell wall and some exfoliated nanolaminae even insert into wood cell walls; and 5) the FTIR analysis suggests that MMT and wood in WMNC perhaps interact via certain chemical bonding.     

Effects of wood species,particle sizes and dimensions of residue obtained from trimming of wood–cement composites on physical and mechanical properties of cement-bonded particleboard

Abstract

The present work was conducted to study the effects of wood species, particle size and residue particle size obtained from trimming of wood–cement composites on physical and mechanical properties of cement-bonded particleboard (CBPB). Particleboard was manufactured with a wood/cement ratio of 1:3 and specific gravity 1200 kg m^?3. After manufacturing, the boards were tested. The second order plan was used to test the significant difference between factors and levels. It was shown that slenderness and compaction ratio increased and bulk density and specific surface decreased with the increase of particle size. With the increase in slenderness ratio and compaction ratio and decrease in bulk density and specific surface, thickness swelling and mechanical properties improved, but water absorption by the board increased. The addition of 6% of 5/3 fraction size of particle obtained from trimming of boards improved significantly the properties of the boards. The optimized panel properties, obtained using poplar particles with a fraction size of 7pass/on5, exceeded the BISON type HZ and EN Standard for Wood Particleboard. CBPB made of alder or poplar particles with 5/3 fraction size of residue exceeded the BISON type HZ. All CBPB with 5/3 fraction size of residue showed lower mean values of thickness swelling, well below the maximum requirements of both standards. In addition, wood species, fraction size of particles and residue size are believed to have been the main cause of change in the properties of the boards.     

Manufacture and properties of Miscanthus–wood particle composite boards

Miscanthus sacchariflorus straw was used as a raw material for the manufacture of Miscanthus–wood particle composite board with Douglas-fir particles in ratios of 100/0, 80/20, 60/40, 40/60, 20/80, and 0/100. A commercial phenol–formaldehyde resin was used as a binder at 9 and 11 % for target densities of 0.50 and 0.65 g/cm³, respectively. The effects of the Miscanthus/wood particle ratio on the composite board properties were investigated. In addition, the density profile was also examined to improve the understanding of the composite board manufacturing process. Results indicate that the internal bonding value increased drastically in the board containing up to 50 % wood particles, providing a valuable parameter for subsequent research. The board properties were greatly improved with increasing density and binder addition level.     

Demarcation of juvenile and mature woods of planted Chinese fir and its wood quality prediction

lntroductionChinesefir(Cunntwh8mi8IanceoIat8(Lamb.)Hook)isaveryimportantspeciesofwoodresourcesinSouthernChina.TheheredityandameliorationonChinesefirareaIwayspaidgreatattention.However,inthepast,thefocaIpointOftheworkonheredityandamelioF8tionwashowtoCuItivatetheChinesefirwithcharaCtersoff8stgrowth,goodfigure,wideadaPt-abilityandStrongdiseaseresistance.LittleworkwasdoneonameIior8tionofwoodquaIity.AlongwiththecompositionchangeoftheforeStresourcesinChina,Chinesewoodindustryismoredependen…     

Geographic variation and genetic performance of Picea koraiensis in growth and wood characteristics

Eight provenances of 19-year-oldPicea koraiensis Nakai from the provenance trials of Maoershan (45°20′N, 127°30′E), Liangshui (47°10′N, 128°53′E) and Jiagedaqi (50°24′N, 124°07′E) in Northeast China were investigated to analyze the genetic variation in growth characteristics (tree height and diameter) and wood characteristics (tracheid length, tracheid diameter, tracheid wall thickness, annual ring width as well as wood density). Great variation in height growth and breast height diameter growth was observed among the provenances, and along with the increase of tree age, these provenances presented different geographic adaptability. The growth characteristics ofPicea koraiensis stand at age of 10 in Maoershan and Liangshui provenance trials had a positive correlation with longitude, and with increase of tree age to 15 and 19, the tree growth of the provenances displayed a significant positive correlation with latitude as well as altitude. For wood characteristics, great variation was also found among the provenances. There exists a close relation between growth characteristics and wood properties of the provenance. The height and breast height diameter growth of the provenance had a positive correlation with tracheid diameter and annual ring width, and a negative correlation with tracheid wall thickness and wood density. Genetic performance of the provenance in all above characteristics was also investigated in order to provide more useful information for comprehensive selection of this species for pulpwood and plywood production. Foundation item: The paper was supported by National Key Project of The State Forestry Administration. (96-011-01-06) Biography: WANG Qiu-yu (1957-), female, professor in College of Life Sciences, Northeast Forestry University, Harbin 150040, P. R. China. Responsible editor: Song Funan     

Isolation of lignin–carbohydrate bonds in wood. Model experiments and preliminary application to pine wood

A novel method for analysis of benzylic ether type lignin–carbohydrate bonds has been developed by using model compounds. Four diastereomers of model compound 3-(4-hydroxy-3-methoxyphenyl)-2-(2-methoxyphenoxy)-3-(methyl -d-glucopyranoside-6-O-yl)-1-propanol (GGMGP), were ozonized in acetic acid/water/methanol 16:3:1 for 1h at 0°C. The product from ozonation of each diastereomer was saponified and the corresponding -etherified tetronic acid (TAMGP) was isolated using ion exchange chromatography. Minor amounts of methyl -d-glucopyranoside (MGP) and small amounts of a gluconic acid etherified with tetronic acid (TAGLCA), tetronic acid, gluconic acid, and glyceric acid were detected in the product mixture of ozonated benzylic ether type model compounds. The results suggest that a benzyl ether bond between lignin and carbohydrate is rather stable during the ozone treatment. Acid treatments with sulfuric acid or trifluoroacetic acid of the derived TAMGP led to cleavage of the glucosidic bond but only a small amount of products (tetronic acid and glucose) resulting from cleavage of the -ether bond were formed. The successful chemical treatments were used for studies of benzylic ether bonds in Japanese red pine. The results suggest the presence of benzylic ether bonds to polysaccharides in the wood.Part of this paper was presented at the 10th International Symposium of Wood and Pulping Chemistry (ISWPC), Yokohama, 1999; the 11th ISWPC, Nice, 2001; and as a rapid comunication in J Wood Sci (2000) 46:263–265     

European standards on durability and performance of wood and wood-based products – Trends and challenges

Abstract

Standardization work in the field of wood durability and preservation is managed, at the European level, by the technical committee TC 38 ‘Durability of wood and wood-based products’ of the European Committee for Standardization (CEN). Producing sustainable wood-based materials is challenging. A crucial aspect of their provision is reliable standards that take consideration of both the expectations of end-users and the broad set of parameters that may influence the service life of wooden components such as exposure to moisture, climatic variations and design. In order to reach these objectives, most CEN/TC 38 standards are currently being revised based on the recent scientific, technological and legal developments in the field of wood protection. There is an increasing need for performance classification of wood products in construction and to radically consider how wood durability test methods and standards can inform on service life and how they might be translated into a performance classification system. This paper describes the changes during the past 5–10 years in Europe and how the trajectory of standards development is now on a different pathway. Classification and service life demands are described as well as current approaches to consider key issues such as material resistance, moisture risk and adaptation of existing standards.     

Dynamic-mechanical analysis and SEM morphology of wood flour/polypropylene composites

Introduction It is well known that over the past few decades, polymers have replaced many conventional materials, such as metal and wood in many applications. This is due to the advantages of polymers over conventional materials (Maurizio et al. 1998; Adr…     

Determination of 2-thiocyanomethylthiobenzothiazole (TCMTB) in treated wood and wood preservative using Ultraviolet–visible spectrophotometer

Ultraviolet–visible Spectrophotometer method for the determination of 2-thiocyanomethylthiobenzothiazole (TCMTB) in treated wood and wood preservative was developed. The determination was done after conversion of TCMTB to 2-mercaptobenzothiazole (2-MBT). This conversion was obtained by reaction with 0.1?M cystein alkaline condition (pH 10). The extraction of 2-MBT was carried out with ethyl acetate containing 0.2% of ?-mercaptoethanol after acidification with 2?M phosphoric acid (pH 2.5). The sample absorbance was measured at 324?nm wavelength with a calibration curve range from 10 to 90?ppm of TCMTB. The Regression value, R ², achieved was 0.9998, while the precision, RSD, was <10% (n?=?6). The recovery was in the range of 90.7–103.2% (n?=?6). The result obtained with this colorimetric procedure is comparable to the HPLC–PDA method.     

Comparison of water absorption and mechanical properties of wood–plastic composites made from polypropylene and polylactic acid

Abstract

This study focuses on the water absorption and mechanical properties of composites made from softwood sawdust and plastics, such as virgin and recycled polypropylene and polylactic acid (PLA). The composites were processed by extrusion, and their properties were investigated by a water immersion test, mechanical tests and a cyclic test for moisture resistance. Scanning electron microscopy was used to study the morphology of the fracture surfaces of the composites. The composites made with recycled polypropylene had the lowest water absorption and thickness swelling of the studied composites. The PLA composites made with heat-treated sawdust showed the highest flexural strength. Of the polypropylene based composites, virgin polypropylene resulted in composites with higher flexural strength. The Charpy impact strength of the composites was found to have an inverse trend compared to flexural strength. Cyclic treatment of the studied composites resulted in 20–60% loss of flexural strength, depending on type of composite.     

A model of supplying poplar wood for Iranian paper ＆ wood factories

The objective of this research is to design a method for an appropriate alternative to supply poplar wood as raw material for wood and paper factories in Iran.Due to the destruction of the forests and lack of proper plantation,replacement of the forest wood by the fast growing wood is vital to satisfy all requirements of these factories.A hierarchy was used to prioritize benefits,opportunities,costs and risks (BOCR) using the Analytic Hierarchy Process (AHP) ratings approach.To evaluate the "control criteria" of the system,a control hierarchy was also created and prioritized by applying the Analytic Network Process (ANP).A total of four major control criteria in the system are prioritized where each one controls a network structure evaluated by using ANP.The final synthesis results of the system showed that internal poplar tree farming supplied by the forest product factories was the best choice among three potential alternatives (factory procurement,external procurement and mix procurement).     

Tannery row – The story of some natural and synthetic wood adhesives

Tannin adhesives are a relatively old but limited speciality which has become again topical with the very marked environment-friendly outlook of wood science at the beginning of the new century. Although the lecture will start by intermingling the technical experience of the author in this field mainly with some humorous stories on the early and not so early beginnings of this speciality, this will only be a brief introduction to more recent scientific/technical developments on mainly synthetic thermosetting adhesives, although natural adhesives will not be forgotten. The lecture will also relate in a very brief form, and without being limiting, some of the author's developments in synthetic (and some natural) resins wood adhesives, and in other fields of wood science and wood technology which might have or have had an impact on the advancement of this field. Received 20 June 2000     

Load behaviors of a prefabricated wood framing house during lifting and transportation

Lifting for handling and flatbed truck transportation to the job site are important processes during manufacture of prefabri-cated wooden construction units like mini homes and building modules. Significant damage can occur to sections or components of units during these operations. Although damage usually will not impair its structural safety, it is costly to fix and causes the public to perceive prefabricated wooden buildings as low quality products. Field observations and preliminary numerical models for prefabri-cated units subject to lifting and transportation forces are summarized here. Once fully developed and verified, models will support the creation of damage mitigation strategies centered on structural details indicating how units are to be supported during lifting and transportation.     

Measurement of standard and off-axis elastic moduli and Poisson’s ratios of spruce and yew wood in the transverse plane

It is well known that in the radial–tangential plane of softwoods, the elastic modulus in the principal directions is clearly higher than the off-axis elastic moduli, which decrease to a minimum at a growth ring angle α of about 45°. However, this angular dependency was experimentally proven by only a few early publications. The aims of this study were (1) to analyze this relationship with up-to-date equipment in compression tests on miniature softwood specimens with varying growth ring angles and (2) to compare the experimental results with those calculated by a tensor transformation to assess whether it is admissible to treat the investigated wood species as orthotropic materials. Two softwoods with distinctly different anatomic structures (Norway spruce and common yew) were chosen, and further properties such as Poisson’s ratios were determined. The results confirm the above-mentioned angle-dependent tendency for spruce elasticity, but also show that it is not valid for softwoods in general since the behavior of yew was completely different. The tissue textures of both species, particularly density and density distribution, were discussed as possible reason for these observed differences. The determined Poisson’s ratios for principal and off-axis load directions may be useful for modeling of material behavior.     

Comparison of wood,fibre and vessel properties of drought-tolerant eucalypts in South Africa§

Three drought-tolerant eucalypt genotypes have been investigated for a broad spectrum of properties to provide a basis for comparison on their suitability for various end-uses. The genotypes included were a Eucalyptus grandis × E. camaldulensis hybrid, E. gomphocephala and E. cladocalyx, selected based on previous studies that indicated good potential to tolerate arid conditions, reasonably good volume growth and straightness of stems. In this study, information was added on differences between species and parts of stems in growth (volume and biomass) and properties of wood (density and stiffness), fibres (dimensions and microfibril angle) and vessels (size and numbers). We found high wood densities and stiffness values for E. cladocalyx and E. gomphcephala, making them suitable for construction wood. Logs from the mid-part of the stem had the best timber properties, as the butt logs showed the highest microfibril angle and lowest wood stiffness due to longitudinal juvenility. Such juvenility was also to some degree observed for wood density and fibre length. The information gained will be especially helpful for selecting species and processing options for small farm and community plantations for producing higher-value products that may be sold to generate much-needed income as well as for local uses, such as fuelwood and charcoal.     

Laboratory and environmental decay of wood–plastic composite boards: flexural properties

The flexural properties of wood–plastic composite (WPC) deck boards exposed to 9.5 years of environmental decay in Hilo, Hawaii, were compared to samples exposed to moisture and decay fungi for 12 weeks in the laboratory, to establish a correlation between sample flexural properties and calculated void volume. Specimens were tested for flexural strength and modulus, both wet and dry, at 23°C and 52°C. Some specimens degenerated to only 15% of original flexural strength. UV radiation had no impact on flexural properties of field-exposed boards; loss occurred mainly on the side opposite to the sun-exposed surface. The mechanism of the aging process on colonization of WPC by fungi was examined and is consistent with development of slow crack growth in the polyethylene matrix combined with wood decay by fungi. Wood particle decay, moisture, and elevated temperature were the major factors causing composite degradation, indicated by accumulation of voids and a severe decrease in flexural properties. To simulate long-term field impact (including decay) on WPC flexural properties in the laboratory, conditioning of specimens in hot water for an extended period of time is required. Exposure to water (70°C/5 days) was adequate for simulating long-term composite exposure in Hawaii of 4?×?15?×?86 mm³ specimens.     

Preparation of Chinese fir wood/MMT nanocomposites and the factors affecting it

The nano intercalation compounding of wood and MMT has important implications for the modification of wood and for the development of new materials. With water-soluble phenol formaldehyde resin as an intermediary, the nanocomposites of Chinese fir (Cunninghamia lanceolata) wood and montmorillonite (MMT) were prepared via three impregnation methods, i.e. normal pres-sure, once and twice vacuum methods. Based on the weight percent gain (WPG) of impregnated wood, the effects of compounding wood and MMT in term...