Effects of wet-spinning conditions on structures,mechanical and electrical properties of multi-walled carbon nanotube composite fibers

A series of composite fibers composed of multi-walled carbon nanotube (MWCNT) and poly(vinyl alcohol) (PVA) are prepared by varying co-flowing wet-spinning conditions such as spinning geometry and PVA concentration, which affect aligning shear stress for MWCNTs during the wet-spinning. Then, structural features, mechanical and electrical performances of MWCNT/PVA composite fibers are investigated as a function of the aligning shear stress of the wet-spinning process. SEM images of the composite fibers exhibit that MWCNTs are wetted effectively with PVA chains. Polarized Raman spectra confirm that the alignment of MWCNTs is enhanced along the composite fiber axis with increasing the aligning shear stress of the spinning process. Accordingly, initial moduli and tensile strengths of the composite fibers are significantly increased with the increment of the aligning shear stress. In addition, it is found that electrical conductivities of MWCNT/PVA composite fibers increase slightly with the aligning shear stress, which is associated with the formation of efficient electrical conduction paths caused by well-aligned MWCNTs along the composite fiber axis.     

Effects of Chemical Functionalization of MWCNTs on the Structural and Physical Properties of Elastomeric Copolyetherester-based Composite Fibers

Elastomeric copolyetherester (CPEE)-based composite fibers incorporating various neat and functionalized multiwalled carbon nanotubes (MWCNTs) were prepared through a conventional wet-spinning and coagulation process. The influence of functionalized MWCNTs on the morphological features, and the thermal, mechanical properties and electrical conductivity of CPEE/MWCNT (80/20, w/w) composite fibers were investigated. FE-SEM images show that a composite fiber containing poly(ethylene glycol)-functionalized MWCNTs (MWCNT-PEG) has a relatively smooth surface owing to the good dispersion of MWCNT-PEGs within the fiber, whereas composite fibers including pristine MWCNTs (p-MWCNT), acid-functionalized MWCNTs (a-MWCNT), and ethylene glycol-modified MWCNTs (MWCNT-EG) have quite a rough surface morphology owing to the presence of MWCNT aggregates. As a result, the CPEE/MWCNT-PEG composite fiber exhibits noticeably increased thermal and tensile mechanical properties as well as a faster crystallization behavior, which stems from an enhanced interfacial interaction between the CPEE matrix and MWCNT-PEGs.     

Effects of surface treatment of ramie fibers in a ramie/poly(lactic acid) composite

The chemical and morphological properties of ramie fibers treated by chemical surface modification were examined with Fourier transform infrared (FT-IR) spectroscopy. The mechanical and thermal decomposition properties were evaluated with respect to tensile strength, tensile modulus and thermogravimetric analysis (TGA). Surface morphological changes were investigated with scanning electron microscopy (SEM). Finally, the capabilities of composites reinforced with various chemically treated fibers were analyzed by investigating tensile and impact strengths. Additionally, the thermal mechanical properties of the composites were investigated with thermal mechanical analysis (TMA). Based on the results of these analyses, we concluded that pectin, lignin and hemicellulose were removed and thermal stability was increased with chemical treatments. The composites reinforced with ramie fiber showed better properties compared with pure PLA matrix with respect to tensile and impact strengths. The peroxide-treated fiber composite had the smallest thermal expansion.     

Effects of Drawing and Heat-Treatment Conditions on the Structure and Mechanical Properties of Polyhydroxyamide and Polybenzoxazole Fibers

We report the preparation of polybenzoxazole (PBO) fiber from polyhydroxyamide (PHA) precursor fiber which is free from strong acid such as polyphosphoric acid. We prepared the PHA fibers with different spin-draw ratios (SDRs) using a wet-spinning method and the PBO fibers with an SDR of 3.5 (SDR-3.5 PBO fibers) were prepared by various heat-treatment temperatures, and investigated their morphology, crystalline structure, and mechanical properties. The simultaneous thermogravimetric analysis-mass spectrometry (STA-MS) and field-emission scanning electron microscopy (FE-SEM) results confirmed that the diameter of the SDR-3.5 PBO fiber was much smaller than that of the SDR-3.5 PHA fiber, due to the release of water during the thermal cyclization reaction which forms the PBO structure. The wide-angle Xray diffraction (WAXD) pattern of the SDR-3.5 PBO fiber heat-treated at 350 °C (SDR-3.5 PBO 350 fiber) showed two peaks, at 2θ=14.83 ° and 24.38 °, and the diffraction angles dropped with increasing heat-treatment temperature. In addition, the initial modulus and tensile strength of the SDR-3.5 PBO fiber heat-treated at 550 °C (SDR-3.5 PBO 550 fiber) were found to be 19.1 GPa and 449.2 MPa, which were much higher than those of the SDR-3.5 PHA fiber, 9.3 GPa and 227.0 MPa, respectively.     

An effective and simple process for obtaining high strength silkworm (Bombyx mori) silk fiber

This article describes a new process for strengthening natural silk fibers. This process is simple yet effective for mass production of high strength silk fibers, enabled by drawing at a lower temperature and immediately heat setting at a higher temperature. The processing conditions were investigated and optimized to improve the strength. Silk fibers drawn to the maximum ratio at room temperature and then heat set at 200 °C show best tensile properties. Some salient features of the resulting fibers are tensile strength at break reaching 533±10.2 MPa and Young’s modulus attaining 12.9±0.57 GPa. These values are significantly higher than those of natural silk fibers (tensile strength increased by 44 % and Young’s modulus by 135 %). Wide-angle X-ray diffraction and FTIR confirm the transformation of silk I to silk II crystalline structure for the fiber obtained from this process. DSC and TGA data also provide support for the structural change of the silk fiber.     

Air-gap spinning of cellulose/ionic liquid solution and its characterization

In order to study the effects of the spinning conditions on the structure and the properties of the regenerated fiber, cellulose was dissolved in ionic liquid and then spun into fiber using an air-gap spinning process. The solution concentration, the take-up speed and the fixation of the fiber ends during coagulation improved the crystallinity and the tensile strength at the same time. The fiber surface became smooth by addition of DMF (dimethylformamide). However, it decreased the crystallinity and the tensile strength of the fibers. We revealed that the developed structure during coagulation determined the morphology and the properties of the fibers. The co-solvent resulted in smooth surface of the fiber and also changed the mechanical properties.     

Effect of Ni-coated short carbon fibers on the mechanical and electrical properties of epoxy composites

Ni-coated short carbon fibers (Ni-SCFs) were prepared using an electrodeposition method. Short carbon fiber (SCF) reinforced epoxy composites were prepared by changing the fiber content (0.1–0.7 wt%). To investigate the effect of Ni-coated short carbon fibers on the mechanical and electrical properties of the composites, we prepared two kinds of reinforcements: the short carbon fibers treated by 400 °C (400 °C treated SCFs) and Ni-SCFs. Fracture characteristics of the composites revealed the Ni coatings and the epoxy matrix had a better interface, so that the results of tensile and bending strength were better in epoxy/Ni-SCFs composites than those in epoxy/400 °C treated SCFs composites. The 400 °C treated SCFs decreased the electrical resistivity of the epoxy composites, compared to the pure epoxy. However the epoxy/Ni-SCFs composites had lower electrical resistivity than epoxy/400 °C treated SCFs with the same fiber content.     

Investigation of jute-lignin-poly (3-hydroxybutyrate) hybrid biodegradable composites with low water absorption

This study developed a novel PHB-lignin-jute biodegradable composite with preferable mechanical properties and low water absorption. The appearances of fracture surface of composites were analyzed by scanning electron microscope. The result suggested a Gaussian-like distribution of the size particles supporting the presence of lignin with a radius smaller than 0.5 μm. According to X-ray diffraction, the presence of lignin and jute fibers was decreased the crystallization of PHB. Moreover, the glass transition temperature of PHB increased, and the endotherm during glass transition was decreased. The maximum tensile strength and modulus of composites were obtained with 30 wt% jute fiber contents and 4 wt% lignin contents. The presence of jute fibers was largely increased the water absorption of composites. However, the presence of lignin was effectively decreased the water absorption of composites at saturation levels.     

Bioprocess preparation of wheat straw fibers and their characterization

Plant fiber reinforced thermoplastic composites have gained much attraction in structural applications such as building and automotive products. Agricultural residues such as wheat straw, bagasse, and corn stover can also be exploited as readily available natural fiber resources for similar applications. The objective of this study was to extract fibers from wheat straw and also to determine the usefulness of fungal retting of wheat straw before extracting the fibers. Wheat straw was mechanically defibrillated using a laboratory-scale mechanical refiner before and after fungal retting. Fiber characteristics such as physico-chemical and mechanical properties, surface characteristics, and thermal properties of the resultant fibers were measured in order to explore the possibilities of using the fibers as reinforcing materials. Retted fibers were stronger than un-retted fibers. The length and diameter of the retted fibers were lower than the un-retted fibers. FT-IR spectroscopic analysis of the wheat straw fibers indicated the fractional removal of hemicelluloses and lignin from the retted fiber. X-ray photoelectron spectroscopy (XPS) of the fibers showed the partial removal of extractives from the surface of the retted fibers. Also, the oxygen to carbon ratio (O/C) of the fibers illustrated that there is more lignin type surface structure for both retted and un-retted fibers. However, slightly higher ratio of oxygen to carbon in the retted fiber indicated a more carbohydrate-rich fiber than the un-retted fiber. Thermal degradation characteristics demonstrated the suitability of processing wheat straw fibers with thermoplastics.     

Relationship between chemical composition,crystallinity, orientation and tensile strength of kenaf fiber

The physical properties of natural growth fibers such as chemical composition content and fiber diameter are highly affected by environmental issues such as environmental changes and fiber extraction methods. These irregularities of the natural fibers seriously affect its utilization in composite as reinforcements. In this study, taking into account the importance of the fiber tensile strength, the correlation degrees between the kenaf fiber tensile strength and the fiber chemical composition, crystallinity, orientation degree were analyzed by the grey relational analysis method. Both the kenaf single fiber and fiber bundle were used as XRD and tensile strength test sample. The chemical composition content and the FTIR were carried out to obtain a correct result of the chemical composition content. It found that for the different XRD and tensile strength test samples, the single fiber showed lower crystallinity, higher orientation degree and tensile strength compared with the fiber bundle. The cellulose content and the orientation degree got the higher correlation degree with single fiber tensile strength, which was 0.674 and 0.640. The highest factor associated with the fiber bundle tensile strength was the orientation degree, the correlation degree was 0.747. The hemicellulose content and the crystallinity also got high correlation degree with the fiber bundle strength, which was 0.687 and 0.640.     

Mechanical behavior of composites reinforced with fibers caroa

Composites were prepared with 13, 23 30 and 40 % fiber and evaluated the mechanical performance in tensile, flexural and impact. The mechanical properties of these composites were also evaluated function of time at 110 °C thermal exposure. Caroa fibers were characterized by techniques such as thermal gravimetric analysis (TGA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that the best mechanical properties were achieved for composites containing 23 to 30 % fiber. The incorporation of 23 % fiber caroa increased both the modulus of elasticity in the tensile test as the flexural strength and impact, the composite with 30 % fiber caroa showed higher tensile strength. The results show that the tensile and flexural strength of the composite decreased with time of thermal exposure. The thermal aging at 110 °C caused a decrease in tensile properties of the composites.     

Production of carbon fibers modified with ceramic powders for medical applications

Carbon fibers and precursor polyacrylonitrile (PAN) fibres that contain either silica or hydroxyapatite particles, imbedded during the spinning process, were studied in this paper. The modified PAN fibers were thermally stabilized using a multi-stage process in the temperature range between 150 to 280 °C in an oxidative environment. Subsequent carbonization leading to obtain carbon fibers was carried on at 1000 °C in an argon atmosphere. The changes of properties of composite precursor fibers taking place during stabilization and carbonization processes were investigated by the combination of Differential Scanning Calorimetry, Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy equipped with energy dispersive X-ray spectrometer and ultrasonic methods. Mechanical properties, such as tensile strength, static Young’s modulus, elongation at fracture were analyzed at each stage of thermal stabilization process. Additionally some traditional measurements like fiber diameter and mass were studied. Ceramic powders added to the spinning solution were present also in composites fibers after stabilization and carbonization process. Such modification allows to avoid the post-treatment operations, for example by coating or covering with films, which were usually necessary in order to obtain bioactive character of implants. Modification of carbon fibers using calcium phosphate or silica can lead to the development of a new materials for the manufacturing of implants which can establish direct chemical bonds with bone tissue after implantation.     

Water and dye-free coloration of wool

A water and dye-free heat treatment method was used to color wool fibers. The heat effect changed wool fibers to different colors from white in a nitrogen atmosphere. The influences of heating temperature and time on the colors of wool were investigated and the mechanical property of colored wool fibers was evaluated. The color strength of wool fibers increased as heat treatment temperature and time increased. The tensile strength retention rate of wool fiber was relatively high (≥90 %) when the heat temperature was below 200 °C. The surface morphologies of wool fibers scarcely changed during the heat treatment. The carbon content of fibers was found to reduce by heat treatment, indicating oxidization of components in the wool fibers in the process of coloration. Heat treatment may provide a water and dye-free approach to color wool and other textile fibers, albeit within a limited color range.     

Evaluation of mechanical properties of jute/glass/carbon fibers reinforced hybrid composites

A study on the tensile and flexural properties of jute-glass-carbon fibers reinforced epoxy hybrid composites in inter-ply configuration is presented in this paper. Test specimens were manufactured by hand lay-up process and their tensile and flexural properties were obtained. The effects of the hybridization, different fibers content and plies stacking sequence on the mechanical properties of the tested hybrid composites were investigated. Two-parameter Weibull distribution function was used to statistically analyze the experimental results. The failure probability graphs for the tested composites were drawn. These graphs are important tools for helping the designers to understand and choose the suitable material for the required design and development. Results showed that the hybridization process can potentially improve the tensile and flexural properties of jute reinforced composite. The flexural strength decreases when partial laminas from a carbon/epoxy laminate are replaced by glass/epoxy or jute/epoxy laminas. Also, it is realized that incorporating high strength fibers to the outer layers of the composite leads to higher flexural resistance, whilst the order of the layers doesn’t affect the tensile properties.     

Hybrid multi-scale basalt fiber-epoxy composite laminate reinforced with Electrospun polyurethane nanofibers containing carbon nanotubes

In this study, we report the fabrication and evaluation of a hybrid multi-scale basalt fiber/epoxy composite laminate reinforced with layers of electrospun carbon nanotube/polyurethane (CNT/PU) nanofibers. Electrospun polyurethane mats containing 1, 3 and 5 wt% carbon nanotubes (CNTs) were interleaved between layers of basalt fibers laminated with epoxy through vacuum-assisted resin transfer molding (VARTM) process. The strength and stiffness of composites for each configuration were tested by tensile and flexural tests, and SEM analysis was conducted to observe the morphology of the composites. The results showed increase in tensile strength (4–13 %) and tensile modulus (6–20 %), and also increase in flexural strength (6.5–17.3 %) and stiffness of the hybrid composites with the increase of CNT content in PU nanofibers. The use of surfactant to disperse CNTs in the electrospun PU reinforcement resulted to the highest increase in both tensile and flexural properties, which is attributed to the homogeneous dispersion of CNTs in the PU nanofibers and the high surface area of the nanofibers themselves. Here, the use of multi-scale reinforcement fillers with good and homogeneous dispersion for epoxy-based laminates showed increased mechanical performance of the hybrid composite laminates.     

Novel fibers prepared from cellulose in NaOH/thiourea/urea aqueous solution

The regenerated cellulose fibers were prepared by wet-spinning from NaOH/thiourea/urea aqueous solvent system for the first time. The effects of coagulation and stretch conditions on the structure, morphology, and mechanical properties of the prepared fibers were investigated by wide-angle X-ray diffraction (WAXD), scanning electron microscope (SEM), and tensile tester, respectively. When the cellulose spinning dope was coagulated in 10% H₂SO₄/12.5% Na₂SO₄ aqueous solution at 15 °C, the prepared fibers had a typical crystalline structure of cellulose II and circular cross-sectional shapes with smooth surface and slightly high tensile properties to viscose fibers.     

Processing and characterization of nickel-plated PBO fiber with improved interfacial properties

A new application of conventional electroless nickel plating to improve the interfacial properties of PBO fibers was reported. The relationship between surface morphology and interfacial properties of nickel-plated PBO fiber was explored. The continuous nickel coating consisted of nickel and phosphorus elements determined by Energy dispersive spectrometer (EDS) and transmission electron microscope (TEM), exhibiting high adhesive durability. The influence of bath temperature and plating time on the crystal structure, microstructure and mechanical properties of nickel-plated PBO fibers was systematically investigated. X-ray diffractometer (XRD) results revealed that the crystal structure among nickel-plated PBO fibers did not show differences. Scanning electron microscope (SEM) and Atomic force microscope (AFM) images showed that the process parameters had a great influence on surface morphology and roughness of nickel-plated PBO fibers, which could directly affect the interfacial properties of nickel-plated PBO fibers. Single fiber pull-out testing results indicated that the interfacial shear strength (IFSS) of PBO fibers after electroless nickel plating had a significant improvement, which reached maximum at 85 °C for 20 min. Single fiber tensile strength of nickel-plated PBO fibers was slightly lower than that of untreated one. Thermo gravimetric analysis (TGA) indicated that nickel-plated PBO fiber had excellent thermal stability.     

Green composites. I. physical properties of ramie fibers for environment-friendly green composites

The surface topography, tensile properties, and thermal properties of ramie fibers were investigated as reinforcement for fully biodegradable and environmental-friendly ‘green’ composites. SEM micrographs of a longitudinal and cross-sectional view of a single ramie fiber showed a fibrillar structure and rough surface with irregular cross-section, which is considered to provide good interfacial adhesion with polymer resin in composites. An average tensile strength, Young’s modulus, and fracture strain of ramie fibers were measured to be 627 MPa, 31.8 GPa, and 2.7 %, respectively. The specific tensile properties of the ramie fiber calculated per unit density were found to be comparable to those of E-glass fibers. Ramie fibers exhibited good thermal stability after aging up to 160°C with no decrease in tensile strength or Young’s modulus. However, at temperatures higher than 160°C the tensile strength decreased significantly and its fracture behavior was also affected. The moisture content of the ramie fiber was 9.9%. These properties make ramie fibers suitable as reinforcement for ‘green’ composites. Also, the green composites can be fabricated at temperatures up to 160°C without reducing the fiber properties.     

Study on polyacrylonitrile fibers modified by blending with polyethylene glycol

A series of water absorbent porous modified polyacrylonitrile (PAN) fibers were prepared using the blends of PAN and various molecular weight of polyethylene glycol (PEG) by wet-spinning process and water bath post-treatment. The chemical structure and morphologies of the modified PAN fibers were studied. The water transportation, water retention, moisture absorption and mechanical properties of the fibers were discussed. Results show that there is no residual PEG in modified PAN fibers after drawing process in hot water bath and post-treatment. With the increase in PEG molecular weight, the fiber surface grooves become deeper, the inner pore size increases, while the mechanical properties decrease. The water absorbing and transferring capabilities of the modified PAN fibers can be improved in varying degrees due to the different pore structures left by series molecular weight of PEG removing.     

Antimicrobial fibers based on chitosan and polyvinyl-alcohol

A series of antimicrobial fibers with different weight ratio of chitosan (CS) and polyvinyl alcohol (PVA) were fabricated via a primarily industrialized trail of wet-spinning method, and the morphology and structure of the resulting fibers were studied with the aid of scanning electron micrography (SEM), infrared spectroscopy (FTIR), and X-ray diffraction (XRD). The CP60 blend fiber (60 % chitosan content) was confirmed as the best optimal sample among the blend fibers owing to strong intermolecular hydrogen bonds between PVA and chitosan and showed the maximum mechanical, antistatic, moisture absorption/desorption properties. The CP60 also exhibited good antimicrobial effects against Escherichia coli and Staphylococcus aureus as the chitosan fiber and could be recommended as the alternative material for the wound dressing and the food packing.