Fire resistance performance on restrained high strength Q460 steel beams

为了研究约束高强度Q460钢梁的抗火性能,在已有约束钢梁分析理论的基础上,引入残余应力,提出了约束钢梁的抗火性能分析方法,并采用普通强度约束钢梁试验数据对分析方法进行了验证。考虑高强度Q460钢材高温下力学性能参数,利用所提出的方法分析了约束高强度Q460钢梁的抗火性能,并与普通强度Q345钢梁进行了对比。对影响约束高强度Q460钢梁的抗火性能参数进行了分析,包括荷载比、残余应力、轴向约束刚度、转动约束刚度和受火方式等。研究表明：所提出的分析方法准确可靠,高强度Q460钢梁抗火性能与普通强度钢梁具有较大的区别,高强度Q460约束钢梁的抗火性能明显优于普通强度约束钢梁。荷载比、轴向约束刚度、转动约束刚度、受火方式对高强度Q460约束钢梁有较大影响。     

焊接加固热作用对工形截面压弯钢构件承载性能的影响

为研究焊接加固热作用及不同初始负载对工字形压弯钢柱承载性能的影响,基于考虑热影响的热结构耦合分析方法进行了热源模型热输入改进,并考虑初始几何缺陷、初始残余应力及摩擦等,完成了不同负载下焊接加固的3个工字形压弯钢柱的模拟分析。研究了焊接位移时程、腹板应力应变重分布及荷载位移关系,通过有限元分析与相应试验结果对比验证,进而获得了试验无法获得的焊接温度场、翼缘与加固板间的焊接应力应变重分布以及翼缘边缘屈服承载力等结果,并将承载力结果与规范计算结果对比,考察了现有设计方法。结果表明,焊接顺序决定焊接变形的发展过程,焊接热输入和初始负载共同决定持载焊接的位移变化范围和焊接残余变形的大小;初始负载越大,应力应变重分布往偏心受力方向发展更多,承载力越低,而初始残余应力不影响极限承载力;采用考虑热影响的有限元方法具有一定可行性和总体安全性,规范设计方法仍有可提升空间。     

掺入工业废料的改性生土材料抗压试验

为合理利用废弃材料改善生土材料力学性能,通过在素土中掺入糯米浆、废玻璃渣和橡胶,形成改性土体材料,设计5种配合比方案,制作Φ102 mm×116 mm圆柱体试块。通过对其进行轴心抗压强度试验,对比不同配比试件的试验现象、抗压强度、变形能力、荷载位移曲线,分析不同掺合料的作用机理、研究不同掺料不同掺量对抗压强度的影响规律,提出了玻璃渣和橡胶掺量的合理范围。试验结果表明,在素土中掺入糯米浆能提高素土抗压强度,掺入糯米浆、玻璃渣和橡胶,可提高抗压强度和变形能力,但其抗压强度随玻璃渣和橡胶掺量的增多增至3.12 MPa后下降。     

T形板肋对预制带肋底板混凝土叠合板弯曲疲劳性能的影响

为研究T形板肋对预制带肋底板混凝土叠合板弯曲疲劳性能的影响,对3块T形肋底板叠合板和1块整浇板进行弯曲疲劳性能对比试验,主要考察T形板肋与疲劳荷载幅值对试件疲劳破坏形态及疲劳损伤程度的影响,得到了在不同疲劳循环加载次数下的跨中动位移、混凝土应变、预应力筋应变、残余变形等,分析了在不同疲劳循环加载次数下的刚度退化情况、荷载-应变分布规律、裂缝分布规律及剩余承载力等。研究结果表明,经历200万次疲劳循环加载后,T形肋底板叠合板无明显的刚度和强度退化,增设T形板肋的叠合板能达到与整浇板相同的弯曲疲劳性能;T形肋底板叠合板正截面弯曲疲劳强度计算可采用普通预应力混凝土受弯构件正截面疲劳应力验算的4个假定,最终以此建立了其正截面弯曲疲劳强度验算方法。     

高温下钢管约束型钢混凝土柱的受力性能

火灾下无防火保护的结构构件温度会迅速上升，从而造成钢材和混凝土的强度明显下降。为了研究火灾下钢管约束型钢混凝土柱的受力性能，考虑火灾下钢管约束型钢混凝土柱的不均匀温度分布及温度对材料力学性能的影响，提出了火灾下受轴心荷载作用的钢管约束型钢混凝土柱承载力的计算方法。利用有限元软件ABAQUS对提出的计算方法进行了验证，结果吻合较好。进而采用该计算方法对影响高温下承载力的参数进行了分析，研究表明：随着构件截面尺寸的增加以及混凝土强度和钢材强度的提高，构件的承载力逐渐增加，而钢管壁厚的改变对承载力并无太大影响。利用有限元软件ABAQUS分析了荷载比、构件尺寸、钢管壁厚等因素对构件耐火极限的影响，发现耐火极限随着荷载比和钢管壁厚的增加而减小，随着构件尺寸的增加而增大。     

早龄期混凝土蠕变模型比较

针对早龄期混凝土的蠕变松弛特性,以配比、强度以及不同加载龄期的混凝土蠕变试验数据为依据,对比研究了CEB-FIP模型、Muller模型、B3模型与笔者所建立变系数四参数Burgers模型的蠕变预测差异。研究结果表明:常用经验模型中,CEB-FIP模型具有较好的适应性,Muller模型对于高强混凝土的蠕变预测较好,基于固化理论的B3模型对于早龄期混凝土的蠕变预测值偏大,准确性较差。对比研究验证了变系数四参数Burgers模型中参数的物理意义与经验取值范围及其合理性与适用性。     

结构消(耗)能元件芯材SN490B本构关系数值模拟

采用消(耗)能元件的结构在遭受地震作用时,元件芯材首先屈服进入塑性阶段,利用其滞回变形消耗地震输入能量,保护主体结构,元件芯材本构关系的数值模拟是对采用消(耗)能元件结构进行抗震分析与设计的基础。为更真实地模拟结构消(耗)能元件芯材在单调和循环荷载下的本构响应,更准确地对采用消(耗)能元件结构进行结构弹塑性地震响应分析,对常用作消(耗)能元件芯材的日本高延性钢材SN490B的单调、循环加载本构及循环骨架曲线进行了数值模拟,包括：采用Esmaeily-Xiao二次流塑性模型模拟材料在单调荷载作用下弹性段、屈服段、强化段和二次流塑段4个阶段;采用混合强化模型模拟材料循环荷载作用下的本构响应,运用大型通用有限元软件ABAQUS结合数值模拟参数对16种不同循环加载制度下的循环加载试验进行模拟,并与试验结果进行对比;采用Ramberg-Osgood模型、无量纲化的Ramberg-Osgood模型及两段式模型模拟循环骨架曲线。研究结果表明：所采用数学模型可以较好地模拟SN490B钢材单调、循环加载本构响应及循环骨架曲线,数值模拟与试验结果拟合较好。     

基于能量守恒定律对西原模型的改进与验证

在油气钻井工程中,由岩石蠕变引起的井眼缩径或井壁坍塌时有发生,本文基于能量守恒定律分析岩石蠕变的3个阶段,阐述传统的蠕变模型难以研究岩石加速蠕变阶段的原因。为此,在西原模型的基础上串联了一个绕组元件,建立改进西原模型及相应的本构方程。根据油气开发过程中所钻遇地层部分岩心的蠕变实验数据,对建立的改进西原模型进行验证,表明该模型能够很好地反映出岩石的蠕变特性,尤其是在岩石所受荷载大于长期强度的情况下,对凸显岩石加速蠕变阶段效果明显。该改进西原模型的提出可为进一步揭示岩石蠕变的客观规律提供理论依据。     

新型土坯墙体房屋抗震性能试验研究

提出了一种新型土坯墙房屋,对新型土坯墙房屋承重墙体的受力及抗震性能进行试验研究。设计三片新型土坯墙试件,研究土坯墙体在竖向荷载和反复水平荷载作用下的破坏过程、破坏形态、滞回曲线和骨架曲线特征以及墙体水平承载力和变形能力等,同时,研究新型构造措施对土坯墙抗震性能的作用。试验表明：新型土坯墙体的破坏模式与配筋混凝土小型空心砌块相似,土坯墙体具有良好的承载力和变形能力。新型构造措施对墙体整体抗震性能作用明显,其连接构造至关重要。与计算结果比较得出,在建筑抗震概念设计原则指导下,抗震设防7度区采用新型土坯墙建造二层房屋具有可行性。     

水平荷载作用下斜坡刚性桩非线性分析

在综合分析现有水平荷载作用下桩基分析方法的基础上,建立了考虑桩侧土体受力状态的斜坡刚性桩力学模型;根据极限平衡原理,建立横向荷载作用下斜坡刚性桩弯矩和应力平衡方程;引入考虑斜坡影响的p-y曲线方法,提出了综合考虑桩侧土体极限承载力与水平抗力系数沿深度呈线性增加的侧向极限承载力与土体抗力承载力系数计算方法,同时,将该方法应用于计算实例,通过与已有有限元和理论计算方法对比分析,计算结果验证了本文方法的合理性与可行性;并利用该方法,分析了斜坡坡角、桩土接触面系数以及地基水平抗力系数对斜坡刚性桩承载特性的影响因素。分析表明:斜坡的坡角、桩土接触面系数对侧向荷载作用下斜坡刚性桩的荷载位移曲线影响明显,而桩侧土的抗力系数对侧向荷载作用下斜坡刚性桩的荷载位移曲线影响不明显。     

Fire Resistance Analysis of High Strength Q460 Steel Beams-Part II：Theory Validation

In the previous companion paper, the fire resistance of high strength steel beams made from Q460 was theoretically studied. The methods to obtain temperature distribution, critical moment, critical temperature and stability coefficient were presented. The temperature distribution and load bearing capacity was analyzed by finite element method, and the validation was evaluated by comparison of results between theoretical computation and finite element analysis as well as experimental results. The comparison was made between Q460 steel beam and mild Q235 steel beam and the difference on fire resistance was obtained. A simplified approach for fire resistance of high strength Q460 steel beams was proposed and an example was given to show the application and reference of the approach.     

FEA of the Loading Capacity of Monolithic Composite Slim Floors with Deep Decks

Steel concrete composite slim floors with the steel beam encased in concrete floor slabs have many advantages, including low structural height, high fire resistance and rapid construction times. These features make such floors a promising for use in multi storey steel buildings. We established a 3D finite element model of a monolithic composite slim floor using the ANSYS software package. We analyzed the loading capacity, deformation behavior, natural vibration frequency, the influence of reinforcement, and the concrete in the floor rib under a uniformly distributed vertical load. We calculated the effective width of mid girder and secondary beams. The following conclusions can be drawn from the analysis results: First, monolithic composite slim floors possess high loading capacity for common buildings. Second, the concrete rib and reinforcement ratio in the rib have significant effects on floor loading capacity. Third, calculation of effective primary beam width should be based on analysis of monolithic floors rather than single beams.     

Deformation Analysis of Thermo Elastic Plastic on ReinforcedConcrete Structure Subjected to Fire

To investigate the mechanical behavior of reinforced concrete structure subjected to fire, the incremental thermo elastic plastic creep constitutive equations of steel and concrete in consideration of temperature and creep deformation were obtained based on different yield rules and the elastic plastic theories. The nonlinear analysis for reinforced concrete simply supported slab was carried out with consideration the variation of the mechanical properties of steel and concrete with temperature. The effectiveness and applicability of the constitutive equations were verified with the test results from relevant literature. The nonlinear analysis was employed for one bay one storey reinforced concrete frame under fire and the variation of displacement at partial nodes was analysed. It was found that the reinforced concrete structure at a high temperature would have a significant deformation. And the displacement change curves of beam column joints of reinforced concrete frame were not monotonous trend and there were inflexion points. The vertical displacement values of beam column joints were less than those at midspan of cross beam.     

Computational Model and Influencing Factor Analysis of Reinforced Concrete Walls under Fire

The finite element software ABAQUS is used to calculate the deformation of reinforced concrete walls under fire. The calculated results agree well with previous experimental results. Based on the finite element model, the influences of such parameters as axial load level, lateral load level, height-to-thickness ratio, wall thickness, concrete compressive strength, steel reinforcement yield strength, steel reinforcement ratio and concrete protection thickness on deformation and fire resistance of walls are analyzed systematically. It is found that, under the conditions of big axial load level or wall thickness without lateral load and small height-to-thickness ratio, the reverse deflection of reinforced concrete walls in fire is apt to occur. Within the work range of parameters in common use, the fire resistance of walls decreases with the increase of axial load level, lateral load level, height-to-thickness ratio, steel reinforcement yield strength or steel reinforcement ratio, and increases with the increase of wall thickness or concrete compressive strength.     

Fire Resistance Analysis of High Strength Q460 Steel Beams-Part I：Theoretical Analysis

In order to investigate the fire resistance of high strength steel beams made from Q460, the method to compute temperature distribution of high strength Q460 steel beams was derived and the temperature distribution was calculated by using finite difference method. The modified equations of temperature for components of steel beam were proposed. According to critical moment at room temperature and mechanical properties of high strength Q460 steel at elevated temperature, the critical moment and stability checking coefficient were obtained by analysis. The load bearing capacity and critical temperature as well as stability factor were studied by using equivalent stiffness method through considering the effect of temperature gradient on stiffness.     

ECC/钢筋混凝土叠合梁正截面受弯承载力试验与理论研究

为了探究ECC/高强钢筋混凝土叠合梁的正截面受弯特征，以及ECC层厚度对叠合梁整体受弯性能的影响，做了两组共5根梁试件的正截面受弯试验。发现与高强钢筋混凝土梁相比，叠合梁的承载力更高，相同荷载下的挠度值和最大裂缝宽度较小。在受弯全过程中其截面应变仍符合平截面假定，钢筋与ECC也可以实现协调变形，说明受拉区使用ECC可以使得高强钢筋的应力得到充分发挥。但ECC层厚度过大可能会使叠合梁发生脆性破坏。进一步地，在此研究的基础上，对已有ECC的本构模型进行简化，忽略其应力强化贡献，并运用叠加原理，提出一种用于计算ECC/钢筋混凝土叠合梁正截面受弯承载力的方法，将计算结果与试验结果及诸多文献结果进行比较，发现吻合度较高。     

Finite Element Analysis of Shear Behavior of Super High Strength Reinforced Concrete Beam

On the basis of testing results of shear behavior from 18 super high strength reinforced concrete restrained beams with web reinforcement, with the cube compressive strength ranging from over 100Mpa, in this paper, the nonlinear finite element analysis procedure was formulated and the analysis of the specimen tests was carried out with the parameters obtained from the experiments and improved constitutive model and failure criteria of materials. Based on the simulated shear resistance test results and practical measured data of eighteen super high strength concrete restrained beams under point load, the equation to compute the shear resistance capacity of such beams was thus obtained by regression. The analytical results agree well with those of experiments.     

Overall Stability Design of Restrained H Section Steel Columns under Axial Load in Fire

The effects of the restraint stiffness ratio, the axial load ratio and the column slenderness on the buckling temperature and failure temperature of a restrained H section steel column under axial load in fire were studied with a calibrated finite element method (FEM) model. And the calculation methods of buckling temperature and failure temperature were proposed. The effect of the restraint stiffness ratio on the buckling temperature and failure temperatures could be expressed with an exponent curve while polynomial functions was appropriate for the effects of the axial load ratio and the column slenderness. The results of the proposed method were in good agreement with those by FEM method and on the safe side.     

Hysteretic Behavior of Composite Deep Beam Infilled Steel Frame

The Quasi static tests of one steel frame and two the composite deep beams infilled steel frames were carried out. The effects of the deep beams on the load capacity, ductility, hysteretic property and energy dissipation of pure steel structure were analyzed. It is found that the hysteresis curve is a straight line with the constant of the stiffness at the beginning and without residual deformation. And the hysteresis curve of specimen was full after yielding, and the skeleton curves had a clear plastic flow phase with triple linear. The lateral drifts of the beam specimens at failure were 1/25 and 1/22. The composite deep beams enhance the initial stiffness, yield load and maximum load bearing capacity of steel frame. Therefore, seismic performance of the composite deep beams is better.     

Study on Effect of Longitudinal Reinforcement Ratio on Shear Behavior of Restrained Beams with Web Reinforcement

In this paper, five restrained beams with web and different longitudinal reinforcement ratio as well as above longitudinal reinforcement truncated were tested under static point loads. On this basis, the overall process of cracking development under shear and the effect of longitudinal reinforcement ratio on shear strength was investigated