Mitigation of subsoil recompaction by light traffic and on-land ploughing: I. Soil response

Mechanically loosened subsoil has been shown to be prone to recompaction. We addressed a sandy loam that had been mechanically loosened by a subsoiler to a depth of 35 cm in 1997 and again in 1998. Perennial grass/clover was grown with limited traffic intensity in 1999 and 2000. A recompaction experiment was conducted in 2001 and 2002 when the soil was grown with oat and winter wheat, respectively. Using the formerly loosened plots, on-land ploughing was compared with traditional mouldboard ploughing with the tractor wheels in the furrow. In addition, the loosened plots were either light-trafficked (<6 Mg axle load and <100 kPa inflation pressure) or heavy-trafficked (10–18 Mg axle load and 200 kPa inflation pressure), respectively. Finally, the soil loosened by non-inversion deep tillage was referenced with a conventional ploughing–harrowing tillage system that never received the subsoil treatment. The conventional treatment was also grown with the grass/clover in 1999 and 2000. On-land ploughing and light traffic was applied in 2001 and 2002 instead of traditional ploughing and traffic for the conventional treatment. Penetration resistance and bulk density was recorded in the field. Undisturbed soil cores were taken in 1998, 1999 and 2002 from the 7–14, 18–27 and 25–30 cm layer and used for measuring total porosity, pores >30 μm and air permeability at −100 hPa matric potential. The results showed that on-land ploughing mitigated recompaction of the upper part of the formerly loosened subsoil. In contrast, only small differences in recompaction between heavy and light traffic were observed. The mitigation of subsoil recompaction was needed for the loosened soil to provide an upper subsoil with similar—not better—pore characteristics than the non-loosened soil in the conventional treatment. The structural conditions in the plough pan improved for the conventional treatment from 1998 to 2002 as indicated by an almost doubling in air permeability. This was interpreted as being related to the growing of grass/clover ley in 1999 and 2000 combined with a shift from traditional tillage and traffic to on-land ploughing and light traffic when growing cereals in 2001 and 2002. Results on root growth and crop yield are reported in an adjoining paper.     

Characterization of soil physical properties and organic matter under long-term primary tillage in a humid climate

Chisel ploughing is considered to be a potential conservation tillage method to replace mouldboard ploughing for annual crops in the cool-humid climate of eastern Canada. To assess possible changes in some soil physical and biological properties due to differences in annual primary tillage, a study was conducted for 9 years in Prince Edward Island on a Tignish loam, a well-drained Podzoluvisol, to characterize several mouldboard and chisel ploughing systems (at 25 cm), under conditions of similar crop productivity. The influence of primary tillage on the degree of soil loosening, soil permeability, and both organic matter distribution throughout the soil profile and organic matter content in soil particle size fractions was determined. At the time of tillage, chisel ploughing provided a coarser soil macrostructure than mouldboard ploughing. Mouldboard ploughing increased soil loosening at the lower depth of the tillage zone compared to chisel ploughing. These transient differences between primary tillage treatments had little effect on overall soil profile permeability and hydraulic properties of the tilled/non-tilled interface at the 15–30 cm soil depth. Although soil microbial biomass, on a volume basis, was increased by 30% at the 0–10 cm soil depth under chisel ploughing, no differences were evident between tillage systems over the total tillage depth. Mouldboard ploughing increased total orgainc carbon by 43% at the 20–30 cm soil depth, and the carbon and nitrogen in the organic matter fraction ≤ 53 μm by 18–44% at the 10–30 cm soil depth, compared to chisel ploughing.     

Effects of alternative tillage systems on soil quality and yield of spring cereals on silty clay loam and sandy loam soils in the cool, wet climate of central Norway

Tillage trials were established on a poorly drained silty loam overlying silty clay loam and on a freely drained sandy loam overlying medium sand, in 1988 and 1989, respectively. Autumn and spring ploughing and two ploughless systems were compared for 12–13 years, with three replications at each site. The ploughless treatments comprised deep versus shallow spring harrowing until 1999, and thereafter autumn plus spring harrowing versus spring harrowing only. In 6 years, treatments with and without fungal spraying of the cereal crops were included. In other years, fungicides were not used. Perennial weeds were controlled by herbicides as necessary, on nine occasions up until 2001. Average spring barley (Hordeum vulgare L.) and spring oat (Avena sativa L.) yields were similar with spring ploughing as with autumn ploughing at both sites. In treatments without ploughing, average yields on the silty loam over clay were 93% of those obtained with ploughing, and on the sandy loam over sand they were 81%. Smaller and non-significant yield differences were found between spring harrowing versus deep spring harrowing, and between autumn plus spring harrowing versus spring harrowing only. Fungal spraying increased yields markedly at both sites (25%), but there was no significant interaction between this treatment and tillage system. Oat was compared with barley in 2 years, with oat performing better under ploughless tillage. At both sites increases in penetrometer resistance occurred in the topsoil of unploughed treatments. These were considered particularly limiting on the sandy loam. On the silty loam there was an increase in surface horizon porosity in the absence of ploughing, which was associated with an increase in topsoil organic matter content. On this soil there was also a tendency toward lower penetrometer resistance at >30 cm depth on autumn plus spring harrowed soil than on ploughed soil, indicating that the plough pan may have diminished. This was supported by observations of greater earthworm activity on unploughed soil. Soil chemical analyses revealed that mineral N and plant-available P and K accumulated in the upper horizon under ploughless tillage. The percentage yields obtained in individual years with autumn as opposed to spring ploughing, were positively correlated with air temperature during 0–4 weeks after planting on the silty loam, and with precipitation during 0–12 weeks after planting on the sandy loam. In the case of yields obtained with spring harrowing only, relative to spring ploughing, positive correlations were found with 0–4 week temperature on both soil types, suggesting that low early season temperatures may limit yields under ploughless tillage.     

Humic substances in soil and crop sciences: P. MacCarthy, C.E. Clapp, R.L. Malcolm and P.R. Bloom (Editors), American Society of Agronomy and Soil Science Society of America, Madison, WI, 1990, 281 pp., price US$ 30.00, ISBN: 0-89118-104-0

Studies were conducted to determine changes in organic matter and microbial biomass carbon in comparison with structural stability at the surface soil (0–5 cm) of a Charlottetown fine sandy loam, an Orthic Podzol, at three tillage and grassland sites situated in Prince Edward Island. The tillage experiments, established for 3–5 years, included comparisons of mouldboard ploughing, direct drilling, shallow tillage, and chisel ploughing. Two indices of soil structural stability were used: mean weight diameter (MWD) and aggregation index (AI). The latter index assigns a weight factor to aggregate size ranges based on their value for plant germination and root growth.Direct drilling and reduced tillage increased the level of soil organic carbon by 10–17%, relative to mouldboard ploughing. Organic carbon was more enriched in 1–2 mm and 4.75–9.00 mm macroaggregates, especially the former, compared with whole soil. The MWD of aggregates after wet sieving was 33% and 55%, relative to the grassland sites, for mouldboard ploughing and direct drilling, respectively. On these soils of similar mineralogy and particle size, a close linear relationship (r=0.942) was observed between organic carbon (r=0.947) and nitrogen (r=0.923). The AI was significantly correlated to both organic carbon and microbial biomass carbon using power regression. In contrast to MWD, the AI under direct drilling and reduced tillage, associated with an organic carbon level of 2.5%, approximated the AI under grass. Overall, the study showed that minimum tillage systems in humid climates can improve structural stability at the soil surface of fine sandy loams over a relatively short time frame.     

Effect of tillage intensity on weed infestation in organic farming

Conservation tillage is not yet widely accepted by organic farmers because inversion tillage is considered to be necessary for weed control. Three long-term experiments were established with combinations of reduced and conventional plough tillage and stubble tillage to determine weed infestation levels in organic farming, i.e. herbicide application being excluded. Experiment 1 (with very low stocking density of perennial weeds) showed that in presence of primary tillage by mouldboard ploughing the number of annual weeds was nearly unaffected by the mode of stubble tillage. In experiment 2, however, with Canada thistle (Cirsium arvense) being artificially established, thistle density was significantly affected by stubble tillage and by a perennial grass–clover forage crop. Experiment 3 combined two levels of stubble tillage (skimmer plough, no stubble tillage = control) with four implements of primary tillage in the order of decreasing operation depth (deep mouldboard plough, double-layer plough, shallow mouldboard plough or chisel plough). Primary tillage by chisel plough resulted in significantly highest annual weed density compared to all other treatments. The natural C. arvense infestation in experiment 3 showed highest shoot density in the “skimmer plough/chisel plough” treatment compared to the lowest infestation in the “skimmer plough/double-layer plough” treatment. The poor capacity of the chisel plough for weed control was also reflected by the soil seed bank (5500 m⁻² C. arvense seeds for chisel plough, <300 seeds for all other primary tillage). A reduced operation depth of the mouldboard plough (“shallow mouldboard plough”) seemed to have an insufficient effect in controlling C. arvense infestation as well. Stubble tillage by the skimmer plough in addition to nearly any primary tillage operation largely reduced both annual weeds and thistle shoots. Most effective in controlling C. arvense was also a biennial grass–clover mixture as part of the crop rotation.Double-layer ploughing is a compromise between soil inversion and soil loosening/cutting and can be regarded as a step towards conservation tillage. In terms of controlling annual weeds and C. arvense, the double-layer plough was not inferior to a deep mouldboard plough and seems to be suitable for weed control in organic farming. Tilling the stubble shallowly after harvest can support weed control in organic farming remarkably, particularly in reducing C. arvense. If no noxious, perennial weeds occur and primary tillage is done by soil inversion, an omission of stubble tillage can be taken into consideration.     

Impacts of long-term and recently imposed tillage practices on the vertical distribution of soil organic carbon

Although many studies suggest that no-tillage (NT) increases soil organic carbon (SOC) within the soil profile relative to mouldboard ploughing, other studies indicate that no net change occurs. The latter studies suggest that NT only stratifies the SOC, where a near-surface increase in SOC is offset by a concomitant decrease in the subsurface. We examined the SOC distribution and stocks in a cool, humid Brookston clay (Typic Argiaquoll) soil under four soil management systems with a corn–soybean rotation. The objectives of this study were to compare the profile distribution and total amount of SOC under long-term (21 years) NT and mouldboard plough (MP) tillage with the changes that occur over 8 years when 13-years continuous NT is converted to MP, and when 13-years continuous MP is converted to NT. In the top 5 cm of soil, the long-term NT management accumulated greater SOC compared with the long-term MP treatment. However, this near-surface increase was offset by lower SOC concentrations in the 10–20 cm depth, resulting in similar total amounts of SOC stored in 0–20 cm for both long-term NT and MP. The SOC stratification that existed after 13 years of NT management was eliminated with one mouldboard ploughing operation, however the total SOC content in the plough layer of the new-MP treatment remained relatively constant over the subsequent 8 years. Soil organic carbon stratification was evident in the new no-tillage treatment 3 years after the cessation of tillage. The continuous build-up of SOC in the surface of new-NT soils was associated with no change in the total amount of SOC in the plough layer relative to long-term NT. This implies that the diminution of SOC in the 10–20 cm depth was at the same rate as the accumulation of SOC in the 0–5 cm depth. Although there was no net effect of tillage on total carbon stocks in this fine-textured soil, SOC stratification required several years to build-up after adoption of NT, but only a single year to destroy under MP.     

Direct drilling and soil loosening for spring cereals on a fine sandy loam in Atlantic Canada

Changes in soil structure and properties, plant growth and diseases and agronomic aspects were determined, after 3 years, on a Charlottetown fine sandy loam, an Orthic Podzol with a perhumid soil moisture regime, subjected to three tillage systems for spring cereals. The tillage systems consisted of direct drilling, soil loosening with a “paraplow” followed by direct drilling and mouldboard ploughing.

Rate of plant growth and other crop measurements were not changed by the tillage systems, except for the depth of seeding. Direct drilling reduced the accumulation of N and K in the plant, and reduced grain N, compared with mouldboard ploughing. Soil loosening prior to direct drilling prevented the decline in N and K accumulation, and increased grain yield and N content, in comparison with mouldboard ploughing. Direct drilling caused changes in soil macro-aggregation and reduced the evaporation rate, and increased microbial biomass C and N, total organic C and N and extractable ions at the soil surface (0–5 cm), compared with mouldboard ploughing. In addition, earthworm numbers were increased under direct drilling. Root lesion and spiral nematodes were not influenced by tillage differences.

Soil loosening prior to direct drilling alleviated the significant reductions in soil macroporosity, and prevented the increase in soil bulk density, soil strength and percentage water-filled pore space (%WFPS) associated with direct drilling alone. Although soil permeability was optimum under direct drilling alone, the relative increase in %WFPS and reduction in soil aeration were associated with a concomitant increase in common root rot.     

Carbon sequestration in a long-term conventional versus conservation tillage experiment

The impact of conservation tillage practices on carbon sequestration has been of great interest in recent years. Changes in the soil organic carbon (SOC) as influenced by tillage, is more noticeable under long-term rather than short-term tillage practices. This experiment analyzed the organic carbon status of soils sampled at depth increments from 0 to 60 cm after 25 years of five tillage treatments in a silt loam soil. Zero tillage (ZT) treatment was compared to conventional tillage practices of mouldboard and chisel plow operations conducted either during the fall or spring season in a randomized complete block design with four replications. The SOC was calculated on depth and equivalent soil mass bases. Contrast analysis showed a significantly (5%) higher soil bulk density for zero versus fall and zero versus chisel tillage operations at 5–10 cm soil depth. The SOC concentration was dependent on the depth of tillage operation and followed the trend of higher SOC for zero, chisel, and mouldboard tillage at 0–5, 5–10, and 20–40 cm depth, respectively. There were more significant differences in the SOC storage when expressed on depth compared to an equivalent soil mass basis. SOC storage was significantly higher for ZT at the 0–5 cm soil depth compared to conventional tillage practices. Contrast analysis on an equivalent mass basis showed that SOC storage was significantly higher for spring tillage compared to fall tillage at 0–60 cm depth. In conclusion, ZT practices increased SOC concentration and storage compared to conventional tillage operations only for the surface layer but not for the entire soil profile.     

Effects of ploughless tillage and straw incorporation on evaporation

The effects of ploughness tillage (stubble cultivation with a disc tiller or a spring tine cultivator, or with both in combination, replacing mouldboard ploughing) on evaporation were investigated using undisturbed soil lysimeters (height = 350 mm, diameter = 300 mm) excavated after spring cultivation in May from field experiments in eastern Sweden. The evaporation process was measured on ploughed and unploughed soil lysimeters, both with or without precipitation and with or without a seedbed. The effects on evaporation of incorporating crop residues with or without precipitation into a ploughed seedbed were also measured. The results from a heavy clay and from a silty clay loam showed that both ploughless tillage and incorporated straw reduced cumulative evaporation. The water-conserving effect was greater in irrigated treatments. The positive effect on water conservation was also greater on the silty clay loam than on the heavy clay. The soil structural changes brought about by ploughless tillage in layers under the seedbed acted to reduce the rate of evaporation from soil.     

Effects of reduced tillage and liming on microbial activity and soil properties in a weakly-structured soil

The effects of reduced tillage and lime on crop yield and soil physical and microbial properties were studied in a weakly-structured silty clay loam soil. Two autumn primary tillage practices were compared, mouldboard ploughing to 20–25 cm and cultivation to 12 cm. Seedbed preparation was carried out by several harrowing operations in the mouldboard ploughed treatment, and with a PTO-driven harrow in the same operation as sowing in the shallow cultivation treatment. The tillage treatments were applied alone or were combined with liming aimed at soil structural improvement. Lime was added as 6.5 Mg CaO ha⁻¹ before the start of the experiment and mixed into the top 12 cm of soil with a disc cultivator. A 4-year crop rotation was used: spring barley, spring oilseed rape, spring/winter wheat and oats, and all crops were compared each year. Crop residues were retained in the experiment and incorporated at cultivation. Aggregate stability was improved by the shallower tillage depth, probably as an effect of an increase in soil organic matter and a more active microbial biomass. Liming had little effect on soil structure variables but increased microbial activity to some extent. This was reflected in higher crop yields, especially when the shallow tillage depth was combined with liming. Penetration resistance in the seedbed subsoil was highest when mouldboard ploughing was carried out in plots without liming. Data were examined with principal component analyses, and the structures in the data were presented as scores and loading plots, which revealed groupings between samples and relationships between variables, respectively.     

Short-term organic matter mineralisation following different types of tillage on a Swedish clay soil

Reduced tillage is proposed as a method of C sequestration in agricultural soils. However, tillage effects on organic matter turnover are often contradictory and data are lacking on how tillage practices affect soil respiration in northern Europe. This field study (1) quantified the short-term effects of different tillage methods and timing on soil respiration and N mineralisation and (2) examined changes in aggregate size distribution due to different tillage operations and how these relate to soil respiration. The study was conducted on Swedish clay soil (Eutric Cambisol) and compared no-tillage with three forms of tillage applied in early or late autumn 2010: mouldboard ploughing to 20–22 cm and chisel ploughing to 12 or 5 cm depth. Soil respiration, soil temperature, gravimetric water content, mineral N and aggregate size distribution were measured. The results showed that respiration was significantly higher (P?<?0.001) in no-till than in tilled plots during the 2 weeks following tillage in early September. Later tillage gave a similar trend but treatments did not differ significantly. Soil tillage and temperature explained 56 % of the variation in respiration. In the early tillage treatment, soil respiration decreased with tillage depth. Mineral N status was not affected by tillage treatment or timing. Soil water content did not differ significantly between tillage practices and therefore did not explain differences in respiration. The results indicate that conventional tillage in early autumn may reduce short-term soil respiration compared with chisel ploughing and no-till in clay soils in northern Europe.     

Effects of tillage depth on organic carbon content and physical properties in five Swedish soils

The soil tillage system affects incorporation of crop residues and may influence organic matter dynamics. A study was carried out in five 15–20 year old tillage experiments on soils with a clay content ranging from 72 to 521 g kg⁻¹. The main objective was to quantify the influence of tillage depth on total content of soil organic carbon and its distribution by depth. Some soil physical properties were also determined. The experiments were part of a series of field experiments all over Sweden with the objective of producing a basis to advise farmers on optimal depths and methods of primary tillage under various conditions. Before the experimental period, all sites had been mouldboard ploughed annually for many years to a depth of 23–25 cm. Treatments included primary tillage to 24–29 cm depth by mouldboard plough (deep tillage) and to 12–15 cm by field cultivator or mouldboard plough (shallow tillage). Dry bulk density, degree of compactness and penetration resistance profiles clearly reflected the depth of primary tillage and substantially increased below that depth. Compared to deep tillage, shallow tillage increased the concentration of organic carbon in the surface layer but decreased it in deeper layers. Total quantity of soil organic carbon and carbon–nitrogen ratio were unaffected by the tillage depth. Thus, a reduction of the tillage depth from about 25 cm to half of that depth would appear to have no significant effect on the global carbon cycle.     

The influence of tillage on the proportion of organic carbon and nitrogen in the microbial biomass of medium-textured soils in a humid climate

Summary Microbial biomass C and N respond rapidly to changes in tillage and soil management. The ratio of biomass C to total organic C and the ratio of mineral N flush to total N were determined in the surface layer (0–5 cm) of low-clay (8–10%), fine sandy loam, Podzolic soils subjected to a range of reduced tillage (direct drilling, chisel ploughing, shallow tillage) experiments of 3–5 years' duration. Organic matter dynamics in the tillage experiments were compared to long-term conditions in several grassland sites established on the same soil type for 10–40 years. Microbial biomass C levels in the grassland soils, reduced tillage, and mouldboard ploughing treatments were 561, 250, and 155 g g^-1 soil, respectively. In all the systems, microbial biomass C was related to organic C (r=0.86), while the mineral N flush was related to total N (r=0.84). The average proportion of organic C in the biomass of the reduced tillage soils (1.2) was higher than in the ploughed soils (0.8) but similar to that in the grassland soils (1.3). Reduced tillage increased the average ratio of mineral N flush to total soil N to 1.9, compared to 1.3 in the ploughed soils. The same ratio was 1.8 in the grassland soils. Regression analysis of microbial biomass C and percent organic C in the microbial biomass showed a steeper slope for the tillage soils than the grassland sites, indicating that reduced tillage increased the microbial biomass level per unit soil organic C. The proportion of organic matter in the microbial biomass suggests a shift in organic matter equilibrium in the reduced tillage soils towards a rapid, tillage-induced, accumulation of organic matter in the surface layer.     

Long-term experiments with different depths of mouldboard ploughing in Sweden

With the main objective to produce a basis for advice to farmers concerning optimal ploughing depth under various conditions, a series of field experiments were initiated throughout Sweden. At 19 sites on various soils (clay content 72–521 g kg⁻¹, organic matter content 21–89 g kg⁻¹) mouldboard ploughing to about 15, 22 and 28 cm depth was repeated annually for up to 17 years. The total number of location-years was 241. Traditional farming had previously been practised at the sites, including annual mouldboard ploughing to 20–25 cm depth. Spring-sown barley (Hordeum vulgare L.) and oats (Avena sativa L.) were the most frequent crops but many other crops were grown less frequently. Crop residues were generally returned to the soil; straw was chopped at harvest. Post-emergence herbicides were regularly used, generally resulting in an adequate control of annual weeds. However, the control of perennial weeds, particularly couch grass (Elymus repens L. Gould) was often inadequate. At ploughing depths of 22 and 28 cm, the mean crop yields were 2% and 3%, respectively, higher than at 15 cm. However, the results varied considerably between sites. In soils with a high silt content, the shallowest ploughing resulted in up to 10% higher yield than deeper ploughing, provided the control of perennial weeds was adequate. The main reason seemed to be improved structural stability in the surface soil because the concentration of organic matter in this layer became higher the shallower the ploughing. In clay soils with relatively stable structure, as well as in sandy soils, the deepest ploughing resulted in the highest yields, probably because of the deeper loosening. At sites where perennial weeds imposed problems, the weed control was better the deeper the ploughing, sometimes increasing the relative yield after deeper ploughing by several percent as compared with shallow ploughing. Most of this effect was obtained already at the intermediate ploughing depth. The results led to the following conclusions for Swedish agriculture. It may be profitable to plough sandy soils annually as deep as 30 cm, coarse sandy soils perhaps even deeper. In clay and clay loam soils, ploughing deeper than 20–25 cm generally cannot be recommended. In silty soils with an unstable structure, mouldboard ploughing, if any, should be shallow (≤15 cm), and perennial weeds should be controlled by other methods.     

Infiltration patterns into two soils under conventional and conservation tillage: influence of the spatial distribution of plant root structures and soil animal activity

The characteristics and properties of the soil macropore system may cause different infiltration behavior under different tillage practices. To evaluate the effect of a specific tillage system on infiltration and percolation with particular regard to the influence of crop structure and soil animal activity dye tracer irrigation experiments were conducted in a silty (Luvisol) as well as in a sandy loam soil (Podzolluvisol). The spatial distribution of water flow paths was experimentally examined at four square areas of 0.49 m², under conservation and conventional tillage. Natural rainstorms were simulated by irrigating the plots with 2.8×10⁻³ M methylene blue solutions. For both soils the root crowns of the agricultural crop, wormcasts and stained soil sections as well as macroscopic conduits were traced on plastic sheets. The investigated soil depths were 0, 5, 10 and 20 cm for the both soils. For the Luvisol, the 30, 40, 50, 80 and 120 cm depths were also studied.For the Luvisol, the conservation tillage plot revealed pronounced vertical connectivity and continuity of the macropore network (maximum depth of stained pores=120 cm), while at the conventional tillage plot, continuous macropores were observed to soil depths of 50 cm, but mainly restricted to the ploughed topsoil (0–30 cm soil depth).For the Podzolluvisol, at the conservation tillage site extensive mulch residues prevented water transport beneath 5 cm soil depth. In contrast, at the conventionally tilled site stained water reached a depth of 20 cm. For all investigated plots on both soil types, the location of the root crowns of agricultural crop and of wormcasts was not related to percolation patterns.The results suggest that conservation tillage on silty soils under agricultural landuse could induce an increased water retention capacity reducing the significance of fast runoff components.     

Tillage effects on plant extractable soil water in a silty clay vertisol in Southern Italy

This paper describes how the CERES-Wheat simulation model can be used to estimate tillage effects on soil water regimes of a silty clay soil in Foggia, Southern Italy. The four tillage treatments compared are traditional mouldboard ploughing, ripper subsoiling, surface disc-harrowing and minimum tillage with rotary hoeing under continuous durum wheat cropping. For each tillage treatment the CERES-Wheat model was used to calculate the water balance for several layers in the root zone.

The water balance routine of the model estimates the water content within saturation and the lower limit at any time. Inputs required by the model are some basic information about the site, weather, genetic parameters and management practices as well as some soil properties, such as albedo, bulk density, organic matter and N contents. The model was calibrated by estimating the genetic parameters for the minimum tillage treatment in the season 1984–1985. The same set of parameters was used for the subsequent validation procedure. Statistical tests proved that the match between measured and simulated soil water content values was quite good. The simulation results also showed some differences among different tillage treatments. The model predicted the lowest plant extractable soil water values and a different water content distribution along the soil profile of the ripper subsoiling in comparison with the other tillage treatments. The soil water content was lower until 20–40 cm depth and higher at 40–60 cm depth in the ripper treatment as compared with the others. In deeper layers differences became non-significant. This might be due to the cracks produced by the ripper through which rainfall infiltrated in deep layers.     

Wirkung mechanischer Belastung auf Gefüge und Ertragsleistung einer Löss‐Parabraunerde mit zwei Bearbeitungssystemen

Effect of mechanical stress on structure and productivity of a loess‐derived Luvisol with conventional and conservation tillage In Germany farmers are committed to caring for the land by a soil protection law. Yet vehicles with ever increasing axle load endanger productivity and environmental quality of arable soils. In spring of 1995 a field experiment was startet on a wet silty Luvisol to test the effect of single mechanical loading on soil and crop characteristics, when managed by mouldboard ploughing (PL) or conservation tillage (CT). CT soils are considered to be more resistant against compactive stresses and to recover from degeneration more rapidly than PL soils. Beside an unwheeled control the loading treatments were light (2 × 2.5 t; number of wheel passes times wheel load); medium (2 × 5 t) and high (6 × 5 t). In 1995 even light loading of the PL soil caused a significant yield decline by 50% in spring barley, but this happened on CT soil only with high loading. In subsequent years with winter wheat and winter barley yield decline was less distinct. Loading of PL soil reduced total root length (from 4 to 1 km m⁻²) and rooting depth (from 70—90 to 40—70 cm), but on CT soil only root length was diminished by high loading. A tillage‐traffic pan (30—35 cm) hindered subsoil rooting in PL, which was favored in CT by earthworm channels. High loading caused compaction to at least 50 cm depth. Within the pan of the PL soil, penetration resistance attained 5 MPa and bulk density 1.65 g cm⁻³. In the CT soil the zone of maximum compaction was closer to the surface (15—25 cm). In PL soil the saturated hydraulic conductivity and the O₂‐diffusion coefficient gradually decreased with loading, but in CT soil only with heavy loading. The compacted top soil was broken in subsequent years by ploughing (PL: 25 cm) or rotary implements (CT: 5—8 cm). With PL, structure in the pan layer and subsoil did not recover, and rooting depth was still limited. Some restoration, however, was indicated with CT. Here transmitting properties increased in time, which was attributed to the reconstruction of root and earthworm channels, as demonstrated by computer tomography. We conclude that in silty soils compacted layers below ploughing depth will hardly be regenerated by internal processes. CT soils are less susceptible to loading, but high stresses are harmful too. Therefore recommending CT as a measure for protecting soil from compaction would not be enough, considering the present development towards heavy field machinery.     

Changes in soil chemical characteristics with different tillage practices in a semi-arid environment

We examined the effects of various tillage intensities: no-tillage (NT), minimum tillage with chisel plow (MT), conventional tillage with mouldboard plow (CT), and zone-tillage subsoiling with a paraplow (ZT) applied in alternate years in rotation with NT, on the topsoil profile distribution (0–30 cm) of pH, soil organic carbon (SOC), organic N and available nutrients on a semi-arid soil from Central Spain. The equivalent depth approach was used to compare SOC, N and nutrient stocks in the various tillage treatments. Measurements made at the end of 5 years showed that in the 0–30 cm depth, SOC and N had increased under NT and ZT compared with MT and CT. Most dramatic changes occurred within the 0–5 cm depth where plots under NT and ZT had respectively 7.0 Mg ha⁻¹ and 6.2 Mg ha⁻¹ more SOC and 0.5 Mg ha⁻¹ and 0.3 Mg ha⁻¹ more N than under MT or CT. No-tillage and ZT plots, however, exhibited strong vertical gradients of SOC and N with concentrations decreasing from 0–5 to 20–30 cm. In the 0–20 cm layer, higher concentrations of P and K under NT and ZT than under MT or CT were also found. Soil pH under NT and ZT was 0.3 units lower than under MT or CT at a depth of 0–5 cm. This acidifying effect was restricted at the surface layer and in the 20–30 cm interval, pH values under NT and ZT were higher than in MT and CT plots. These results suggest that in the soil studied, ZT in rotation with NT maintain most advantages associated with NT, and present a definite potential for use as a partial-width rotational tillage practice.     

Interactive effect of tillage depth and mulch on soil temperature, productivity and water use pattern of rainfed barley (Hordium vulgare L.)

Soil porosity and organic matter content influence the hydrology, thermal status and productivity of agricultural soils. Shape, size and continuity of soil pores are determined by tillage practices. Thus appropriate tillage and mulch management can conserve residual soil moisture during the post rainy season. This can play a key role in enhancing productivity under the rainfed ecosystem of subhumid region in eastern India. A field study was carried out on a fine loamy soil from 1993–1994 to 1995–1996. Two tillage treatments were conventional ploughing (150 mm depth) and shallow ploughing (90 mm) depth. Each tillage practice was tested with three mulch management viz., no mulch, soil dust mulch and rice (Oryza sativa L.) straw mulch. Soil organic carbon, bulk density, moisture retentivity, soil temperature with productivity and water use pattern of barley (Hordium vulgare L.) were measured.Reduction in ploughing depth resulted in nominal increase in profile (0.0–1.2 m) moisture status, yield, and soil thermal status at 14:00 and water use efficiency (WUE). However, it decreased the magnitude of soil temperature in the morning (07:00). Straw mulch conserved 19–21 mm of moisture in the profile (1.2 m) over the unmulched condition. Both soil dust and rice straw mulching elevated soil thermal status at 07:00 as compared to unmulched condition, but this trend was reversed at 14:00. Straw mulching significantly increased grain yield and WUE over soil dust mulch and unmulched condition. Impact of straw mulch was more pronounced under shallow ploughing depth. Shallow tillage with rice straw mulching is recommended to the farmers to obtain higher level of yield and water use efficiency.