Fabrication and characterization of nano Al<Subscript>2</Subscript>O<Subscript>3</Subscript> filled PVA:NH<Subscript>4</Subscript>SCN electrolyte nanofibers by electrospinning

Present paper reports a method of preparing polymer composite electrolyte nanofiber mat using polyvinyl alcohol (PVA), ammonium thiocynate (NH₄SCN) salt, and aluminium oxide (Al₂O₃) nano particles based on electrospinning technique. Two-stage process of preparation of nanofibers, namely, preparation of nano particles filled PVA electrolyte gel solution followed by its electrospinning has been used. The so obtained nanofibers have been characterized by XRD, DSC, SEM, and Conductivity measurements. XRD patterns affirm the formation of nanocomposite while SEM pictures reveal formation of fibers on a nano scale format (300–800 nm). Fibers of the electrolytes are seen to be thermally stable. Ionic conductivity of electrolyte fiber is seen to improve in the presence of nano filler at room temperature with a maximum at 5.31×10⁻³ Scm⁻¹ for 4 wt% filler concentration, which is comparable to that for corresponding dried gel electrolyte films.     

A Comparative study of redox parameters and electrochemical impedance spectroscopy of polycarbazole derivatives on carbon fiber microelectrode

In this study, N-Carbazole and its derivatives (N-Vinylcarbazole, N-Ethylcarbazole, N-Vinylbenzylcarbazole, and N-Benzylcarbazole) were electrochemically polymerized on carbon fiber microelectrodes (diameter ∼7 μm) by cyclic voltammetry within a potential range from 0.0 to 1.4 V. Redox parameters, Scanning electron microscopic (SEM) images were determined and also capacitance behaviors of polymers were examined via electrochemical impedance spectroscopy (EIS). EIS measurements of polycarbazole derivatives were given comparatively. The existence of a capacitance behavior is shown by Nyquist, Bode magnitude, Bode-phase, Admittance plots relationship. Although the highest low frequency capacitance (C_LF=12901 μA cm⁻²) and maximum phase angle of 81.9 ° at a frequency of 1 Hz were obtained for N-Vinylbenzylcarbazole, the lowest anodic and cathodic potential difference (ΔE=0.04 V) and double layer capacitance (C _dl =0.11 μA cm⁻²) were indicated in 0.1 M LiClO₄/PC.     

Preparation and properties of solid polymer electrolyte based on imidazolium-based ionic liquids for structural capacitors

We prepared solid polymer electrolytes (SPEs) composed of poly(ethylene glycol) monomethyl ether acrylate (1A9OMe) and 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIm][OTF]) and 1-ethyl-3-methylimidazolium bis(trifluoromethane sulfonyl) imide ([EMIm][TFSI]) as the ionic liquid. The SPEs formed by appropriately adding ionic liquids in the 1A9OMe prior to thermal cure. The ratio of 1A9OMe and ionic liquid was 1:9, 3:7, and 5:5, respectively. The characterization of solid polymer electrolytes were investigated using Fourier transform infrared spectroscopy in the attenuated total reflectance mode (FTIR-ATR), Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and glavanostatic charge-discharge test. The highest ionic conductivity of SPEs was found to be 4.90×10^?4 S/cm in a 1A9OMe/[EMIm][OTF] of 3:7. As IL contents were increased, the specific capacitance of supercapacitor was increased. The specific capacitance of supercapacitor for ionic liquid with large ion size was lower than that for ionic liquid with smaller ion size.     

Polycarbazole modified carbon fiber microelectrode: Surface characterization and dopamine sensor

Electropolymerization of carbazole (Cz) by cyclic voltammetry (CV) onto carbon fiber microelectrodes (CFME) (diameter ∼7 μm) in dichloromethane (CH₂Cl₂) solution of 0.1 mol·dm⁻³ tetraethyl ammonium perchlorate (TEAP) results in the formation of polycarbazole (PCz) thin film coatings. CV results showed that these PCz thin films have reversible redox behavior in monomer-free electrolyte solution. The resulting thin polymer films were characterized using Fourier transform infrared attenuated total reflectance spectroscopy (FTIR-ATR) and atomic force microscopy (AFM). Results performed at optimum experimental conditions indicate that electrodes show a reversible and stable behavior over sixty eight days of testing for dopamine in 100 μmol·dm⁻³ buffer solution. A detection limit for PCz thin films as low as 0.1 μM (3S/N) was obtained for the polycarbazole (PCz) thin films formed using CV. Hence, this novel sensor can be considered as promising sensor for dopamine detection.     

Effects of plasticizer on the mechanical properties of kenaf/starch bio-composites

Research and development of biodegradable bio-composite can replacement the synthetic polymer materials, which is used for automobile interior materials, finishing materials of air conditioner and refrigerator. To develop both components as biodegradable bio-composite, this research used natural polymer starch as matrix and kenaf fiber as a filler. Various plasticizer(polyvinyl alcohol, polyethylene glycol, glycerol) were added and examined the mechanical properties of the kenaf/starch bio-composites according to these plasticizer. The kenaf bast which cultivated in Korea was retted with 2 % NaOH solution. The plasticizer weighting 10 % of that of matrix was added. kenaf/starch composites were molded with hot press for 30 minutes at 130 °C and 3,500 PSI molding condition. The mechanical properties such as tensile strength, elongation, and young modulus of the kenaf/starch composites were measured. Also, we measured the SEM cross-section images in order to investigate interfacial adhesion properties of fractured surfaces. The order of strength size of composites were G (12.42 MPa) > PVA (9.72 MPa) > PEG (4.73 MPa) samples respectively. The tensile strength of PEG sample is lower than the control sample (5.40 MPa).     

Preparation of the Multicomponent High Temperature Proton Exchange Membranes with Layer by Layer Self-assembly Technique

Layer by layer (LBL) self-assembly technique has been proved to be a feasible method that enables to accomplish the preparation of functional membranes with multilayered structure. In this research, the polymer of sulfonated polyetheretherketone (SPEEK) and thioglycolic acid capping of cadmium telluride (CdTe) nanocrystals as polyanion, the polymer of polyurethane (PU) as polycation have been used to prepare membrane electrolytes. These multilayered membranes showed good thermal stability and exhibited low liquid methanol permeability, which provided a possibility for the prepared membranes as proton exchange membranes (PEMs) to apply in direct methanol fuel cells (DMFCs). We have also demonstrated that the multicomponent (SPEEK/PU/CdTe/PU)₁₀₀ membranes favored to combine more phosphoric acid (PA) molecules and possessed a higher proton conductivity comparing to the bicomponent (SPEEK/PU)₂₁₀ membranes. So PA doped (SPEEK/PU/CdTe/PU)₁₀₀ membrane presented a maximum proton conductivity up to 8.6×10^-2 S/cm at 160 °C under anhydrous conditions. However, PA doped (SPEEK/PU)₂₁₀ membranes underwent a drop on proton conductivity while the temperature exceeded 120 °C.     

The quality of tomato for canning as affected by combined chloride,nitrate and osmotic potential of the nutrient solution

The quality of tomato fruit and juice (Lycopersicon esculentum L. cv. VF M82-1-8) grown in an aerohydroponic system in a greenhouse was affected by the level of Cl^– and NO ₃ ^– , and by the osrnotic potential (OP) of the nutrient solutions. The total suspended solids (degrees Brix) in the fresh juice increased from approximately 4.0 in the nonsaline solutions (OP –0.05 MPa) to approximately 5.6–5.8 in the saline solutions (OP –0.45 MPa). Juice acidity was similarly affected by the Cl^–, NO ₃ ^– and OP levels in the nutrient solutions. Less affected, the ascorbic acid content of juice, was lowest ( 8–9 mg/100 cc) in the high-NO ₃ ^– -nonsaline solution treatments, and was between 10 and 12 mg/100 cc at OP levels greater than –0.2 MPa. NO ₃ ^– in the juice was high ( 60 mg/L) under low OP conditions ( –0.05 to –0.1 MPa), especially when combined with high NO ₃ ^– levels, and lower (between 8 and 30 mg/L) in plants exposed to saline conditions (low OP). Fruit puffiness (boxiness) was reduced markedly by salinity and was not considerably affected by the NO ₃ ^– /Cl^– ratio, while fruit firmness was influenced by both factors.Contribution from the Agricultural Research Organization (ARO), The Volcani Center, Bet Dagan, Israel.     

Gold recovery using inherently conducting polymer coated textiles

The ability of inherently conducting polymer (ICP) coated textiles to recover gold metal from aqueous solutions containing [AuCl₄]⁻ was investigated. Nylon-lycra, nylon, acrylic, polyester and cotton were coated with a layer of polypyrrole (PPy) doped with 1,5-naphthalenedisulfonic acid (NDSA), 2-anthraquinonesulfonic acid (AQSA) orp-toluenesulfonic acid (pTS). Textiles coated with polyaniline (PAn) doped with chloride were also used. The highest gold capacity was displayed by PPy/NDSA/nylon-lycra, which exhibited a capacity of 115 mg Au/g coated textile, or 9700 mg Au/g polymer. Varying the underlying textile substrate or the ICP coating had a major effect on the gold capacity of the composites. Several ICP coated textiles recovered more than 90% of the gold initially present in solutions containing 10 ppm [AuCl₄]⁻ and 0.1 M HCl in less than 1 min. Both PPy/NDSA/nylon-lycra and PAn/Cl/nylon-lycra recovered approximately 60% of the gold and none of the iron present in a solution containing 1 ppm [AuCl₄]⁻, 1000 ppm Fe³⁺ and 0.1 M HCl. The spontaneous and sustained recovery of gold metal from aqueous solutions containing [AuCl₄]⁻ using ICP coated textiles has good prospects as a potential future technology.     

Development of biodegradable films based on blue corn flour with potential applications in food packaging. Effects of plasticizers on mechanical,thermal, and microstructural properties of flour films

In the present study, blue corn flour films were developed. The cereal grain’s total composition (excluding the pericarp) is used to obtain the films. The plasticizing effects of two different polyols such as glycerol and sorbitol on the mechanical, thermal, and microstructural properties of flour films were researched. The results showed that films plasticized with sorbitol had better mechanical properties and less affinity for water than those plasticized with glycerol. The sorbitol-plasticized films were more rigid and did not lose their integrity when immersed in water. The ATR-FTIR spectra of blue corn flour plasticizer with sorbitol showed the presence of the additional band at 1745 cm⁻¹ characteristic of the vibrational carbonyl peak, which confirms the chemical linkages between sorbitol and a polymeric matrix. The effect of the plasticizer on the glass transition temperature (T_g) was characterized using differential scanning calorimetry (DSC). T_g decreased as the plasticizer content increased. Plasticized glycerol films showed lower T_g values than those with sorbitol. SEM observations showed that it was necessary to add plasticizer to maintain film integrity. The sorbitol-plasticized flour films revealed better adhesion between phases, and these films showed a compact structure.     

The acid doping behavior of polybenzimidazole membranes in phosphoric acid for proton exchange membrane fuel cells

The acid doping behavior of poly(2,2′-(m-phenylene)-5,5′-bibenzimidazole) (PBI) membranes in aqueous phosphoric acid was studied at room temperature. It was found that doping phosphoric acid in the membrane obeyed a multimolecular layer absorption mechanism proposed in this work. Equation, i.e., 1/[L ^T ] _B =(1 − C ₀/17.5)/2.1, was presented to describe the relationship of the acid doping level of membranes and the concentration of the doping acid in a range of 2–14 mol L⁻¹. The acid doping kinetics as well as the influence of the doped acids on the conductivity and mechanical strength of the PBI membranes was investigated.     

Preparation and properties of polypropylene nanocomposites reinforced with exfoliated graphene

We have prepared a series of polypropylene/exfoliated graphene (PP/EG) nanocomposite films via efficient meltcompounding and compression, and investigated their morphology, structures, thermal transition behavior, thermal stability, electrical and mechanical properties as a function of EG content. For the purpose, EG, which is composed of disordered graphene platelets as reinforcing nanoscale fillers, is prepared by the oxidation/exfoliation process of natural graphite flakes. SEM images and X-ray diffraction data confirm that the graphene platelets of EG are well dispersed in PP matrix for the nanocomposites with EG contents less than 1.0 wt%. It is found that thermo-oxidative degradation of PP/EG nanocomposites is noticeably retarded with the increasing of EG content. Electrical resistivity of the nanocomposite films was dramatically changed from ∼10¹⁶ to ∼10⁶ Ω·cm by forming electrical percolation threshold at an certain EG content between 1 and 3 wt%. Tensile drawing experiments demonstrate that yielding strength and initial modulus of PP/EG nanocomposite films are highly improved with the increment of EG content.     

Structure and performance of fibers prepared from liquefied wood in phenol

The fibers from liquefied wood in phenol (WPFs) were spun by adding hexamethylenetetramine as synthetics and cured by soaking in solution containing hydrochloric acid and formaldehyde as main components. The chemical structure of WPFs remarkably changed from that of liquefied wood was identified by FT-IR spectrometer. WPFs with the average diameter of 27∼42 μm, tensile strength of 230∼356 MPa, and modulus of 15∼31 GPa were obtained using spinning speed of 0.72 μm min⁻¹, hydrochloric acid concentration of 18.5 %, heating rate of 10 °C h⁻¹, and curing time of 4 h. These WPFs showed a high thermal stability and a complex thermal decomposition process by TG(thermogravimetric) analysis. It was also found that the two obvious weight loss temperatures of WPFs were 510°C and 748°C.     

Investigation on ion conduction behaviour in Zn-ferrite based polymer nanocomposite electrolyte

Present paper deals with, improvement in ion transport property and dielectric relaxation of polyethylene oxide (PEO)-based polymer electrolytes subsequent to dispersal of nanosized Zn-ferrite filler particles. The nanocomposite polymer electrolyte (NCPE) system [93PEO:7NH₄SCN]: x% Zn-ferrite was prepared by solution cast technique through dispersal of sol gel derived Zn-ferrite nano powder in the pristine polymer electrolyte solution. The structural and morphological behavior of NCPEs have been studied by XRD, SEM, IR and DSC measurements. Electrical conductivity (both a.c. & d.c.) measurement on nanocomposite polymer electrolyte sample have been carried out using impedance spectroscopic technique. Dielectric relaxation studies were extracted by impedance data. The hopping ion transport mechanism in NCPEs has been concluded with the help of dielectric and modulus formalism.     

Spatial variability of soil saturated hydraulic conductivity in paddy field in accordance to subsurface percolation

Insufficient puddling with inappropriate implements or imprecise time/intensity may alter saturated water flow in paddy soil spatially or temporary due to change in aggregate size distribution, dry bulk density, saturated hydraulic conductivity, and percolation rate of the soil. In this study, spatial variability of saturated hydraulic conductivity (K _s), a key parameter of the saturated water flow, in Fuchu Honmachi paddy plot (100 m × 28 m) was characterized based on dielectric or ADR dry bulk density (ρ_b-ADR) with help of non-similar media concept (NSMC) and geostatistics model to meet its correlation to subsurface percolation. A 100 cc core and an ADR data were sampled from each sub-plot (7 m × 7.5 m), and then were used for measuring and predicting ρ_b and K _s. The predicted data agreed with the measured ones, in which they fitted well the x = y line with RMSE of 0.029 cm³ cm⁻³ (R ² = 0.68), 0.027 g cm⁻³ (R ² = 0.71) (ρ_b), and 0.098 cm d⁻¹ (R ² = 0.45) for θ, ρ_b, and K _s, respectively. The predicted ρ_b and K _s had similar trend in spatial variability to the measured ones particularly within the distance of 46.3–51.9 m and 26.2–27.9 m, respectively. The spatial variability of the predicted K _s coincided to that of the subsurface percolation rate, in which they had similar distance of dependence. The results indicated that the presenting method can be reasonably accepted.     

Partitioning of glutenin flour of special wheat using aqueous two-phase systems

The partitioning behavior of the glutenin proteins was evaluated in aqueous two-phase systems (ATPSs) formed by sulfate salts (lithium or sodium) and poly(ethylene glycol) (PEG) with average molar mass of 1500 g mol⁻¹ or 4000 g mol⁻¹. The partition coefficients for the glutenin proteins in each ATPS were investigated as a function of the temperature (278.2 K–318.2 K), tie line length (TLL) and electrolyte nature. In all ATPS, the majority of glutenin proteins spontaneously concentrate in the polymer-rich phase (K_p > 1). The partition coefficient is very dependent on the salt nature and the ATPS formed by PEG + lithium sulfate presents higher K_p values as compared with the ATPS formed PEG + sodium sulfate. An increase of molar mass of polymer promotes a decrease of K_p. Thermodynamic parameters of transfer (Δ_trG, Δ_trH and Δ_trS) were obtained by the application of the Van’t Hoff equation (VHE). The values obtained by VHE indicate that the transfer of glutenin proteins to the polymer-rich phase has an enthalpic origin.     

Thermal degradation studies of poly(o-anisidine) doped with 5-sulfosalicylic acid

Thermal decomposition of the solid state of poly(o-anisidine) (POAN) base (POAN-EB) and salt [doped with 5-sulfosalicylic (SSA) acid] (SSA-doped POAN) forms has been studied by thermogravimetric analysis (TGA) and differential thermal analysis (DTA) under non-isothermal conditions. The potential (PE) and optimum molecular geometric (OMG) energies of the repeating unit (tetramer form) of investigated matrix were calculated using molecular mechanics (MM+) calculations. These calculations (PE= −3.48×10⁹ and OMG=−122.72 kJ mol⁻¹) indicate that the optimum molecular geometric structure of this matrix is highly stable. The empirical formula of the doped polymer is best represented by [POAN-2SSA.n/6H₂O] and substantiate by elemental analysis and MM+ calculations. The full polymer decomposition and degradation were found to occur in three stages during the temperature increase. The decomposition activation energy (E _d) of both POAN base (POAN-EB) and its doped (SSA-doped POAN) were calculated by employing different approximations. The heating rate of decomposition and the frequency factor (k _o ) as well as kinetic parameters were calculated for doped or base form of this matrix. A remarkable heating rate dependence of the decomposition rate of the SSA-doped POAN matrix was observed.     

Effect of nitrogen source on growth and morphogenesis of three micropropagated potato cultivars

Summary Different nitrogen sources (NO₃ ⁻, NH₄ ⁺, glutamic acid and their combinations) influenced the growth and morphogenic responses (node number, shoot length, and stem, leaf and root dry weight) of three micropropagated potato cultivars (Spunta, Kennebec, Huinkul). Addition of reduced nitrogen (NH₄ ⁺ or glutamic acid) in a nitrate medium increased shoot length and leaf number. The large increase in growth in plants fed with NO₃ ⁻, NH₄ ⁺ could be explained by higher organic nitrogen content and enhanced dry matter partition to the shoot. This suggests that reduced nitrogen source is required, at least as a supplement to NO₃ ⁻, to enhance N assimilation and growth.     

Synthesis, characterization, and protonation of poly(2-N,N-dimethylamino-4,6-bis(2-furan)-pyrimidine)

A new monomer (2-N,N-dimethylamino-4,6-bis(2-furan)-pyrimidine) was synthesized and its homopolymer was successfully prepared by using ferric trichloride as an oxidant. The structure of monomer and polymer were fully characterized by ¹H-NMR, FT-IR, UV, fluorescent spectroscopy, and X-ray diffraction. The N,N-dimethylformamide solution of the polymer showed a UV-Vis peak at 387 nm and the PL spectrum gave a peak at 517 nm. We have observed that the polymer was sensitive to inorganic acids and the protonation behavior was investigated applying inorganic acids such as HCI and H₂SO₄. The corresponding UV-Vis peaks were observed at 464 and 357 nm, respectively. X-ray diffraction data shows that polymer had a certain crystalline region. The polymer exhibited an [η] value of 0.21 dl/g at 25 °C in H₂SO₄ (w=98 %).     

Preparation of cellulose/multi-walled carbon nanotube composite membranes with enhanced conductive property regulated by ionic liquids

Cellulose/multi-walled carbon nanotubes (MWCNTs)- composite membranes applied in electrochemical and biomedical fields were prepared using 1-ethyl-3-methylimidazolium diethyl phosphate (EmimDEP) as solvent in this study. With the increasing of MWCNTs amount, the membrane conductivity increased, and the conductivity reached 9.1 S/cm as the mass ratio of MWCNTs to cellulose being 2:1. The additions of sodium dodecyl sulfate (SDS), 1-hexadecyl-3-methylimidazolium bromide (C₁₆mimBr) and 1-butyl-3-methylimidazolium tetrafluoroborate (BmimBF₄) efficiently improved the conductivity, mechanical property, and thermal stability by promoting the dispersion of MWCNTs. When the mass ratio of C₁₆mimBr to MWCNTs changed from 0 to 0.3:1, the conductivity increased from 0.08 S/cm to 0.14 S/cm, and the tensile strength increased from 13.3 MPa to 17.0 MPa. These results indicate that the binary ionic liquids (ILs) system can regulate the properties of the composite membranes, and is a feasible approach for preparing cellulose/MWCNTs composite membranes with enhanced properties.     

Microtuberization of Potato (Solanum tuberosum L.) as Influenced by Supplementary Nutrients, Plant Growth Regulators, and In Vitro Culture Conditions

Five experiments with in vitro-grown plantlets of potato cvs ‘Superior,’ ‘Early Valley,’ ‘Golden Valley,’ and ‘Winter Valley’ were carried out to investigate in a stepwise approach the potential for enhancing microtuber production of (1) adding supplementary nutrients (SN) including KNO₃, NH₄H₂PO₄, Ca(NO₃)₂.4H₂O, and MgSO₄ in full- or half-strength Murashige and Skoog (MS) medium, (2) adding a pretested combination of plant growth regulators (PGRs), i.e., 10 mg l⁻¹ 6-benzyl aminopurine plus 200 mg l⁻¹ succinic acid 2,2-dimethylhydrazide, (3) varying the timing of the supplemental applications, and (4) varying the replenishment of the medium. Plantlets of ‘Superior’ for microtuberization were grown from two-node explants for 75 days under environmental conditions consisting of 22 ± 2 °C and a 16-h photoperiod on a solid basal medium consisting of half-strength MS (1/2 MS) medium containing 6 % sucrose and a moderate concentration of supplementary nutrients, SN-2 (KNO₃, 1.22 g l⁻¹; NH₄H₂PO₄, 1.41 g l⁻¹; Ca(NO₃)₂4H₂O, 0.23 g l⁻¹; and MgSO₄, 0.74 g l⁻¹). Thereafter, plantlets were grown for 60 days under dark conditions. Liquid media containing different combinations of MS, SN, and PGR levels plus 8 % sucrose were added as a supplement and were evaluated for their ability to increase tuberization compared to the control composition of the supplement (MS with 8 % sucrose). In the first experiment, addition of 1/2 MS liquid medium containing 8 % sucrose and SN-2 before dark incubation induced the highest total number of microtubers (on average 1.4 per plantlet), a significantly higher weight and size than the control, and the highest percentage (50 %) of large-sized (>500 mg) microtubers. In the second experiment, addition of 1/2 MS liquid medium containing 8 % sucrose, SN-2, and PGRs produced the highest number (on average 1.5 per plantlet) and total yield (on average 971 mg per plantlet) of microtubers, and significantly the highest percentage (66 %) of large-sized (>500 mg) microtubers. The size of the microtubers was higher than for the treatment without growth regulators. The optimum time for addition of supplemental medium containing 8 % sucrose, SN-2, and PGRs was shown in experiment 3 to be latest 1 week before dark incubation. This timing resulted in both the highest microtuber number (on average 1.6 per plantlet) and yield (on average 1208 mg per plantlet), and the highest percentage (64 %) of large-sized microtubers. Finally, it was found that a second supplemental treatment consisting of 50 % replacement of the liquid medium (by volume) 2 weeks after transfer to dark conditions gave rise to the highest number (on average 1.9 per plantlet), yield (on average 1346 mg per plant), and also significantly the highest percentage (25 %) of large-sized microtubers (>1000 mg) as compared to replacement of a greater or smaller proportion of the medium. Four potato cultivars, ‘Superior,’ ‘Early Valley,’ ‘Golden Valley,’ and ‘Winter Valley’ produced acceptable numbers and yield of microtubers of relatively large-sized tubers using a process that included supplemental liquid medium with 1/2 MS, 8 % sucrose, moderate concentration (SN-2) of SNs and PGRs, followed by a 50 % replacement of the same medium.